1987 NISSAN PULSAR check oil

156
FRONT SUSPENSION
SPECIFICATIONS
Type.................. Independent MacPherson strut with
coil springs and control arms
Shock absorber .................. Hydraulic, non-repairable
Hub bearing end float (maximum) ............. 0.05 mm
Ball joint axial play (maximum) ....................0.7 mm
Ball joint turning torque (used)...............0.5-4.9 Nm
Wheel alignment:
Toe in ..................................................... 0-2 mm
Camber ........................................- 0 ° 1 0 ' ± 4 5 '
Caster ..............................................1 ° 1 0 ' ± 4 5 '
King pin inclination..................... 1 3 ° 5 5 ' ± 4 5 '
TORQUE WRENCH SETTINGS
Hub bearing nut..................................... 196-235 Nm
Suspension unit to steering knuckle nut ...... 118 Nm
Suspension unit to body nuts ......................... 29 Nm
Piston rod nut .................................................. 72 Nm
Brake caliper to steering knuckle bolts ........... 52 Nm
Ball joint to steering knuckle bolt ................... 86 Nm
Control arm bracket bolts ............................... 98 Nm
Control arm pivot bolt ................................ 118 Nm
Stabiliser bar link nuts..................................... 44 Nm
Stabiliser bar bracket bolts .............................. 21 Nm
1. FRONT SUSPENSION TROUBLE
SHOOTING

FRONT END NOISE
(1) Loose upper suspension mounting or piston
rod: Tighten the mounting or piston rod nuts. (2) Loose or worn suspension unit lower ball
joint: Tighten or renew the lower ball joint.
(3) Noise in the suspension unit: Renew the
faulty suspension unit, preferably in pairs.
(4) Worn or loose steering gear: Overhaul the
steering gear assembly. (5) Worn front hub bearings: Renew the hub
bearings:
(6) Loose or defective stab ilizer bar, control arm
or mountings: Check, tighten or renew the mounting
rubbers.

Check the ball joints for wear and deterioration.
(7) Worn stabilizer bar link ball joints: Renew
the stabilizer bar links.
(8) Drive shafts worn or insufficiently lubri-
cated: Check the lubricant and the dust boots and
renew as necessary. (9) Drive shaft splines in the hub or the
differential worn or dama ged: Check and renew as
necessary.

NOTE: To check the front suspension com-
ponents for wear, raise the front of the
vehicle, support it on chassis stands and
allow both front wheel to hang free. With an
assistant pushing and pulling the front
wheels in and out at the top and then at the
bottom, check for excessive looseness at the
front hub bearings and lower control arm
inner pivot bushes. Noise or vibration in the
front end can also be caused by excessive
tire or wheel unbalance. Drive shaft joint
noise is usually more pronounced when
moving slowly with the steering on full lock.

POOR OR ERRATIC ROAD HOLDING
ABILITY

(1) Low or uneven tire pressures: Inflate the
tires to the recommended pressures.

(2) Defective suspension unit: Renew the faulty
unit, preferably in pairs.

Front Suspension 157


Check the stabilizer bar links for wear and damage.
(3) Incorrect front end alignment: Check and
adjust the alignment as necessary. (4) Defective stabilizer bar mounting rubbers or
worn link ball joints: Renew component as necessary. (5) Weak or broken front coil spring: Renew
both springs as a matching pair. (6) Broken or weak rear coil spring: Renew both
springs as matching pair. (7) Drive shaft bent or distorted: Check and
renew as necessary. (8) Tie rod end worn or damaged: Check and
renew as necessary.
(9) Control arm ball joint worn or damaged:
Check and renew as necessary.
(10) Control arm mounting bolts loose: Tighten
the control arm bolts. (11) Wheel hub bearing worn: Check and renew
as necessary. NOTE: As a quick guide to suspension unit
condition, bounce the front of the vehicle up
and down (one side at a time), the vehicle
should come to rest in a single movement. If
it bounces two or three times before stop-
ping, the suspension unit should be renewed.
If the from of the vehicle is tower on one
side than the other, remove the coil spring
and check its free length against a new
spring. If the spring is found to be unservice-
able it is good practice to install two new
springs as a matching pair. This also applies
to the springs on the rear of the vehicle.

2. DESCRIPTION
The front suspension is an independent type
comprising two Macpherson strut suspension units
mounted vertically on each side of the vehicle. The
lower end of the suspension unit is bolted to the
steering knuckle, which in turn houses the front hub
bearings. The steering knuckle pivots on the control
arm by means of a ball joint.

The control arm pivots at its inner ends on rubber
bushes.

A stabilizer bar is attached to both ends of the
control arms using ball joint links. The stabilizer bar
is attached to the front underbody by brackets and
mounting rubbers.

Each front suspension unit assembly comprises a
tubular shock absorber type suspension unit, sur-
rounded at the upper end by a coil spring. On top of
the coil spring is the upper mounting which attaches
to the underside of the inner mudguard panel. The
piston rod of the suspensi on unit is attached to the
centre of the upper mounting by a rubber mounted
bearing.

When a suspension unit is found to be defective it
is recommended that both suspension units be re-
newed as a pair.

Camber is adjusted by means of a cam on the
upper steering knuckle to suspension unit mounting
bolt.

The kingpin inclination and caster are set in
production and cannot be adjusted. Any variation in
these angles will be caused by worn or damaged
components.

3. STEERING KNUCKLE
Special Equipment Required:
To Renew Wheel Bearing — Press and press plates
and suitable tubes and mandrels
To Check Hub End Float — Dial gauge
TO REMOVE AND INSTAL
(1) Raise the front of the vehicle and support it
on chassis stands. Remove the front wheel.


Checking the control arm bolts for security.

Front Suspension 159
(4) Install the tie rod end to the steering knuckle
and tighten the castellated nut securely. Install a
new
split pin.
(5) Install the brake disc to the hub.
(6) Install the brake caliper to the steering
knuckle and tighten the retaining bolts to the specified
torque. (7) Install the hub nut and washer to the
drive
shaft and with the aid of an assistant applying the
brakes, tighten the hub nut to the specified torque. (8) Install the hub nut retainer and a new
split
pin to the drive shaft. (9) Check the hub end float as described later in
this section. (10) Install the fron t wheel and lower the vehicle
to the ground.
TO DISMANTLE

NOTE: The front wheel bearing assembly is
non-serviceable. If the wheel bearing is dis-
mantled for any reason it should be re-
newed.

(1) Remove the steering knuckle from the vehi-
cle as previously described. (2) Hold the steering knuckle assembly in a vice
with soft jaw guards. (3) Using a hammer and a suitable pipe or tube
that pushes on the inside of the hub, drive out the
wheel hub and outside inner race from the steering
knuckle assembly. (4) Using snap ring pliers, remove the snap ring
that retains the outer bearing race from the wheel side
of the steering knuckle. (5) Using a suitable press and press plates,
support the steering knuckle with the outside face
downwards. To aid in dismantling, position the inside
inner race in the bearing and press the assembly from
the steering knuckle. Discard the bearing assembly. (6) Using a bearing puller and a press, remove
the inner race from the hub assembly. If the inner race cannot be removed from the hub
in this manner, it may be necessary to grind the race

using an angle grinder and split the race using a cold
chisel.

(7) Thoroughly clean and dry the steering
knuckle and hub in a suitable solvent. (8) Inspect all the components for wear, damage
and cracks and renew if necessary.
TO ASSEMBLE

Assembly is a reversal of the dismantling proce-
dure with attention to the following points:

(1) Apply grease to the oil seal lips of the new
bearing assembly.

NOTE: Ensure that (he inside of the outer
race of the bearing is precoated with wheel
bearing grease. If necessary, pack the outer
race of the wheel bearing with wheel bearing
grease after it is installed to the steering
knuckle.

(2) Using the press and press plates, support the
steering knuckle with the outside face uppermost.
Using a suitable diameter steel tube that contacts on
the outer race only, press the outer race full into the
steering knuckle.
(3) Install the snap ring to the groove in the
steering knuckle.
(4) Install the inner races to the steering
knuckle
and support the inner race on the press using a
suitable tube or mandrel. (5) Using the press and a suitable tube press the
hub assembly into the steerin g knuckle. When using
the press ensure that the pressing force does not
exceed 29 kN. (6) With the press exerting a force of 44.1 kN
rotate the steering knuckle from side to side several
turns to ensure that the wh eel bearings are operating
smoothly.
(7) Install the steering knuckle to the vehicle
as
previously described.
TO CHECK HUB END FLOAT

(1) Raise the front of the vehicle and support it
on chassis stands. Remove the front wheel.
(2) Mount the dial gauge on the steering knuckle
so that the dial gauge plunger is against the wheel hub.
(3) Zero the dial gauge and attempt to move the
hub in and out. Total hub e nd float should not exceed
0.05 mm. (4) Renew the wheel bearing as previously de-
scribed if necessary.
4. SUSPENSION UNIT

Special Equipment Required:
To Dismantle — Spring compressor
TO REMOVE AND DISMANTLE
(1) Raise the front of the vehicle and support it
on chassis stands. Remove the front wheels.
Dismantled view of the steering knuckle and hub
components.

160 Front Suspension

(2) Disconnect the flexible brake hoses from the
suspension unit bracket.
(3) Using quick drying paint, place mating
marks on the camber adjustin g cam head bolt and the
suspension unit lower mounti ng as an aid to installa-
tion. (4) Remove the bolts and nuts retaining the
suspension unit lower mounting to the steering
knuckle. (5) Open the bonnet and remove the nuts
retaining the suspension unit upper mounting to the
inner mudguard panel and remove the suspension
unit assembly from the vehicle. Use care when
removing not to damage the drive shaft boot.

(6) Remove the dust cover and loosen the piston
rod nut but do not remove it at this stage. (7) Install a spring compressor to the
suspension
unit assembly. Compress the coil spring and remove
the piston rod nut. (8) Remove the washer, upper mounting assem-
bly, the thrust washer, spring seat, insulator, coil
spring, bump rubber and dust cover from the suspen-
sion unit. (9) Check the operation of the suspension unit.
With the suspension unit in a vertical position, move
the piston rod up and down a number of times. A

Dismantled view of the front suspension unit.
uniform resistance should be felt with no abnormal
slack spots or noise evident. If the suspension unit is
defective, it should be renewed.

NOTE: It is recommended that the suspen-
sion unit on the opposite side be renewed at
the same time.

(10) Check the upper mounting assembly for
damage and fatigue. Check the thrust washer for wear.
Check all rubber components, the spring seat and
insulator for wear, damage and deterioration. Renew
worn or damaged components. (11) Check the coil spring for fatigue by compar-
ison with a new spring. Al so check the spring for
cracks and damage. If the coil spring is defective, it is
recommended that the springs on both sides be
renewed.
TO ASSEMBLE AND INSTAL

Assembly and installation is a reversal of the
removal and dismantling procedure with attention to
the following points:
View of the front suspension unit with the spring
compressor installed.

Front Suspension 161


View of the suspension unit and knuckle assembly removed as a unit to show the cam head bolt.
(1) With the piston rod fully extended, install the
coil springs. Ensure that the spring compressor is
tightened sufficiently.

NOTE: The flat coiled end of the spring
should face the top and the lower end of the
spring should be located correctly.

(2) Install the dust cover, bump rubber, insulator,
spring seat, thrust washer and mounting assembly
ensuring that the arrow on the spring seat will face the
outside of the vehicle when the suspension unit
assembly is installed.
(3) Install the piston rod nut and tighten the nut
securely.
(4) Remove the coil spring compressor from the
suspension unit assembly and tighten the piston rod
nut to the specified torque. (5) Install the suspension unit assembly to the
vehicle, holding it in position by loosely installing the
upper mounting retaining nuts. (6) Install the suspension unit assembly lower
mounting to the steering knuckle, align the mating
marks on the cam head bolt and tighten the nuts and
bolts to the specified torque.
NOTE: If the cam head bolt is not installed

in its original position, a wheel alignment
must be performed.

(7) Tighten the upper retaining nuts to the
specified torque.
(8) Install the brake hoses to the suspension unit.
Lower the vehicle to the ground.
(9) Check the front wheel alignment and adjust
as necessary. Refer to the Suspension and Steering
Angles heading in this section.
5. CONTROL ARM
Special Equipment Required:
To Renew Ball Joint and Control Arm Bushes —
Press, suitable t ubes and mandrels
To Test Ball Joint — Small torque wrench or
preload gauge, spring scale

TO REMOVE AND INSTAL
(1) Loosen the front wheel nuts, raise the front
of the vehicle and support it on chassis stands.
Remove the front wheel.

(2) Remove the split pin from the ball joint
retaining nut and remove the nut.
(3) Disconnect the ball joint from the control
arm using a suitable puller, or alternatively place a
suitable dolly against one si de of the control arm eye
and strike the opposite side with a hammer until the
ball joint stud is free from the control arm eye. (4) Remove the nut retaining the stabilizer link
to the control arm.

(5) Remove the nut and through bolt from the
front control arm bush. (6) Remove the bolts from the rear control arm
bush bracket and withdraw the control arm from the
vehicle. (7) Inspect the control arm for cracks, damage
and distortion and renew if necessary. (8) Inspect the ball joint and bushes for damage,
deterioration and excessive wear. If necessary renew
BALLJOINT
View of the control arm and associated components.

162 Front Suspension
the ball joint or bushes as described later in this
section.

Installation is a reversal of the removal procedure
with attention to the following points:

(1) When installing the control arm bush
bracket, ensure that the protrusion on the bracket is
towards the inside of the vehicle.
(2) Do not fully tighten the control arm bush
bolts and through bolt nut until the curb weight of the
vehicle is on the suspension.
NOTE: Curb weight is with the vehicle
unladen except for a full tank of fuel and
normal amounts of oil and water and with
the spare lyre, jack and hand tools in their
normal positions.

(3) Tighten the ball joint nut to the specified
torque and retain with a new split pin.

TO CHECK AND RENEW BALL JOINT
(1) Remove the control arm from the vehicle as
previously described.

(2) Install the ball joint nut and turn the ball
joint at least ten revolutions to ensure that the ball
joint is correctly seated. (3) Using a spring scale with the hook placed
over the split pin hole, check the ball joint swinging
torque. A new ball joint should measure 15.7-80.4 N
and a used ball joint should measure 7.8-80.4 N.
Renew the ball joint if necessary. (4) Using a small torque wrench or preload
gauge, measure the force requi red to rotate the ball
joint. A new ball joint should measure between
1.0-4.9 Nm and a used ball joint should measure
between 0.5-4.9 Nm. Renew the ball joint if neces-
sary.

(5) To renew the ball joint, remove the snap ring
from the stud end of the ball joint using snap ring
pliers. (6) Support the control arm in a press, ball joint
stud uppermost, with a suitable tube that is large
enough for the ball joint to pass through. (7) Press the ball joint out from the control arm.
(8) Press a new ball joint into the control arm
using a suitable tube that pushes on the outer circum-
ference of the joint only.
(9) Install the snap ring and install the
control
arm to the vehicle as previously described.

TO RENEW CONTROL ARM BUSHES
(1) Remove the control arm from the vehicle as
previously described. Mark the position of the rear
control arm bush. (2) To remove the rear control arm bush use a
bearing puller and a press. When installing the bush
use a suitable tube that pushes on the inner edge of the
bush only. NOTE: Ensure that the bush is installed
with the flat portion in its original location.

(3)
To remove the front control arm bush use a
suitable tube that pushes on the outer circumference
of the bush and a split tu be supporting the control
arm. (4) After the bush has been pressed out approx-
imately half way, cut the protruding part of the bush
using a hacksaw. Cutting the bush in this way will
allow removal.
(5) Support the control arm and push the new
bush in from the outside using a suitable tube that
pushes on the outer circumference only. (6) Install the control ar m to the vehicle as
previously described.
6. STABILISER BAR
TO REMOVE AND INSTAL
(1) Raise the front of the vehicle and support it
on chassis stands.

(2) Remove the bolts at the flexible joint retain-
ing the front engine pipe to the exhaust pipe located
below the stabilizer bar. (3) Remove the bolt from the exhaust pipe
mounting below the stabilizer bar. Disconnect the
exhaust pipe at the flexible joint and allow the front of
the pipe to hang down. (4) Remove the stabilizer bar bracket retaining
bolts and remove the stabilizer bar brackets from the
vehicle. (5) Remove the stabilizer bar lower link nuts
from each control arm. When removing the lower nuts
it may be necessary to hold the upper nuts with a
spanner.
(6) Maneuver the stabilizer bar from the
vehicle.
Installation is a reversal of the removal procedure
with attention to the following points:

(1) Ensure that the stabilizer bar mounting rub-
bers are in a serviceable condition and secure in the
mounting brackets.

Dismantled view of one end of the stabilizer bar.

164
REAR SUSPENSION
SPECIFICATIONS
Type........................... Independent MacPherson strut
Shock absorber.................... Oil filled, non-repairable
Maximum hub bearing end float ................. 0.05 mm
Rear wheel alignment:
Toe out ........................................3 mm ± 2 mm
Camber ............................................. - 1 ° ± 4 5 '
TORQUE WRENCH SETTINGS
Hub retaining nut ......................................... 255 Nm
Suspension unit retaining nuts ....................... 29 Nm
Upper mounting retaining nut ........................ 72 Nm
Suspension unit to knuckle nuts .................. 118 Nm
Control arms to knuckle nut ........................ 118 Nm
Control arms to crossmember nut ............... 118 Nm
Stabiliser bar mounting bracket bolts .......... 108 Nm
Stabiliser bar retaining nut.............................. 83 Nm
Backing plate bolts........................................... 45 Nm
1. REAR SUSPENSION TROUBLE SHOOTING
REAR END NOISE
( 1 ) Defective suspension unit or mounting: Re-
new the faulty components.

(2) Loose or worn control arm bushes or pivot
bolts: Check and tighten or renew the worn compo-
nents. (3) Broken coil spring: Renew the coil spring,
preferably in matching pairs. (4) Worn rear hub bearing: Check and renew the
hub bearing as necessary. (5) Loose or worn stabilizer bar bushes: Check
and tighten or renew the worn components.
NOTE: As a quick guide to suspension unit
condition, bounce the vehicle up and down
(one side at a time) and observe if the vehicle
comes to rest in a single movement If the
vehicle bounces two or three times before
coming to rest the susp ension unit is suspect.
If suspect, remove the suspension unit and
check for fractures and leaks. If the
suspension unit is found to be unserviceable,
it is good practice to install two new
suspension units as a matching pair.

To check the control arm bushes or pivot
bolts, insert a lever between the suspect unit
and its mounting and lever the unit back
and forth checking for excessive movement.

Check the coil springs visually for breaks.
If the spring is found to be unserviceable, it
is good practice to install two new coil
springs as a matching pair.

Rear hub bearing noise can be diagnosed
by raising and supporting the rear of the
vehicle, spinning one wheel at a time and
listening for a rumbling noise.

POOR OR ERRATIC ROAD HOLDING ABILITY
(1) Low or uneven tire pressure: Inflate to the
recommended pressures.
(2) Incorrect rear wheel alignment: Check and
adjust the rear wheel alignment as necessary.
(3) Defective suspension unit: Renew the faulty
suspension unit, preferably in pairs. (4) Loose or broken stabilizer bar: Check and
tighten or renew the faulty components.
Check the stabilizer bar bushes and mounting rubbers
for wear and deterioration.

Rear Suspension 165


Checking the rear control arm outer pivot bolt for security.
(5) Loose or worn control arm bushes or pivot
bolts: Check and tighten or renew the worn compo-
nents.

NOTE: Check the service ability of the sus-
pension units, control arm bushes and pivot
bolts as previously described.

If incorrect rear wheel alignment is sus-
pected, it is recommended that the vehicle be
taken to a wheel alignment specialist or a
Nissan dealer to be checked and if necessary
adjusted.

Visually inspect the stabilizer bar for
damage.

2. DESCRIPTION
The independent type rear suspension consists of
a suspension unit, a knuckle assembly which incorpo-
rates the stub axle, inboard control arms and a
stabilizer bar.

The suspension unit consists of a sealed, oil filled
shock absorber, enclosed at the upper end by a coil
spring on which an upper mounting assembly is
located and attached to the body.

The shock absorber piston rod is attached to the
centre of the suspension unit upper mounting assem-
bly.

The lower end of the suspension unit is attached
to the knuckle assembly to which the brake caliper
and/or the brake backing plate is mounted.

The control arms are attached to the knuckle
assembly at the outer end, and the crossmember at the
inner end.

The stabilizer bar is attached to the knuckle
assembly and mounted to the underbody. As well as
reducing body roll when cornering it also secures the
knuckle assembly, preventing fore and aft movement.

Adjustment of the toe out is provided by a
graduated cam mounted on the rear control arm inner
pivot bolt. Each graduation on the cam is equivalent
to 2 mm adjustment.

Camber is set in production and cannot be
adjusted. If the camber is not within Specifications,
inspect the suspension components and renew the
damaged or worn components as necessary.


Installed view of the rear suspension.