1987 NISSAN PULSAR ECU

228 Body


Installed view of the front door lock striker plate.
engages the striker plate, loosen the retaining screws
and move the striker plate up or down to eliminate
the lift or drop.

Installation is a reversal of the removal procedure
with attention to the following points:

Ensure that the seal is in a serviceable
condition and correctly installed to prevent the entry
of dust and water. Tighten all the screws securely.
3. REAR DOORS

INTERIOR HANDLES AND TRIM PANEL
To Remove and Install
On models with manual windows, carefully
prise out the armrest trim plugs and remove the
retaining screws. Withdraw the armrest from the
vehicle. On models with power windows, proceed as
follows:
Carefully prise out the armrest trim plugs
and remove the retaining screws. Hold the armrest away from the door trim
panel as much as possible and lever the window
switches out from the armrest, front end first.
Lift the switches and disconnect the wiring
connector. Remove the hidden screw, working through
the switch aperture. Withdraw the armrest from the
vehicle. (3) Remove the screw retaining the remote con-


EXTERNAL MIRROR
To Remove and Install

On models with manual mirrors, remove the
screw retaining the adjuster arm handle and withdraw
the handle. Carefully prise out the cover trim plate and
remove the retaining screws securing the mirror body
to the door. On models with power mirrors, disconnect
the mirror wiring connector. Withdraw the external mirror and seal from
the door.

Rear door with the trim panel and plastic sealing sheet
removed.
SNIPPER BUTTON
REMOTE CONTROL

Dismantled view of the power door mirror.

232 Body
leaving the ends of the string protruding from the
tailgate. Untie the string.

NOTE: The string will be used to pull the
wiring through the tailgate on installation.
If the wiring is pulled from the tailgate
without the string attached, installation will
be very difficult.

With the aid of an assistant supporting the
tailgate, prise out the ball joint stud snap locks from
each upper strut ball joint using a small screwdriver.
Remove the bolts retaining the hinges to the
tailgate and carefully withdraw the tailgate from the
vehicle.
To Install and Adjust
With the aid of an assistant, install the
tailgate in position on the hinges according to the
marks made on removal and install the retaining bolts.

Install the tailgate support struts and retain
the ball joints with the snap locks. Pull the tailgate wiring through using the
piece of string. Connect the wiring and install
the
tailgate trim panel. Close the tailgate and check the vertical and
lateral alignment of the tailgate in relation to the
body. If adjustment is required, loosen the tailgate
hinge retaining bolts one hi nge at a time and adjust
the tailgate as required. If vertical adjustment is required, it will be
necessary to remove or install washers under the
tailgate hinges. If required, adjust the striker plate using the
procedure that follows.
STRIKER PLATE
To Remove, Install and Adjust
Using a flat bladed screwdriver, prise out the
trim plugs and remove the trim plate from above the
striker.

Using a soft lead pencil, scribe a line around
the striker plate.

Remove the striker plate retaining bolts and
partially remove the striker plate. Disconnect the remote tailgate release cable
from the striker plate and remove the striker plate
from the vehicle. Inspect the striker plate for wear and renew
it if necessary. Installation is a reversal of the removal procedure
with attention to the following points:

Install the striker plate ensuring that it is in
the position marked on dismantling and that the
remote tailgate release cable is connected. Tighten the
retaining bolts. Close the tailgate ensuring that the striker
has actuated the locking mechanism. Check the alignment of the tailgate in its
opening and adjust the locking action by moving the
striker plate in the requir ed direction. Tighten the
retaining bolts securely.
LOCK AND LOCK CYLINDER
To Remove and Install
Prise out the tailgate trim panel retaining
clips and carefully maneuver the tailgate interior
trim panel from the tailgate.

Disconnect the actuati ng rod from the lock
cylinder assembly. Disconnect the interior lamp switch wiring
connector.


Installed view of the striker plate assembly. Hatchback
models. Dismantled view of the Hatchback lock and lock cylin-
der.

Body 233
Remove the lock assembly retaining bolts
and withdraw the lock assembly, insulator and link
from the tailgate.
Using a suitable screwdriver, remove the
lock cylinder retaining clip and withdraw the lock
cylinder from the vehicle. Installation is a reversal of the removal procedure
with attention to the following points:

Ensure that the positioning of the lock is
correct in relation to the striker plate.
Ensure that the interior lamp switch wiring
connector is connected.
6. LUGGAGE COMPARTMENT LID
AND LOCK — SEDAN
LUGGAGE COMPARTMENT LID
To Remove
Raise the luggage compartment lid and place
protective covers over the surrounding paintwork.
Using a soft lead pencil, mark around the
luggage compartment lid hi nges to aid assembly.
With the aid of an assistant supporting the
lid, remove the hinge retaining bolts and withdraw the
luggage compartment lid from the vehicle.
To Install and Adjust

With the aid of an assistant, install the
luggage compartment lid in position on the hinges
according to the marks made on removal. Install the
retaining bolts. Close the lid and check the vertical and
lateral alignment of the l i d in relation to the body.
If adjustment is necessary, loosen the l i d
hinge retaining bolts on one hinge at a time and adjust
the lid as required.
If vertical adjustment is required, loosen the
lid hinge retaining bolts and increase or decrease the
number of washers under the bolts. If required, adjust the striker plate using the
procedure that follows.
STRIKER PLATE

To Remove, Install and Adjust
Fold back the trim material from inside the
luggage compartment.
Using a soft lead pencil, scribe a line around
the outside of each striker plate retaining bolt washer. Remove the striker plate bolts and washers
and the screw retaining the remote release cable
bracket.

Installed view of the luggage compartment lid striker
with the trim material folded back.
(4) Slide the striker assembly towards the right
hand side of the vehicle and disconnect the remote
release cable. Withdraw the striker plate from the
vehicle.

Installation is a reversal of the removal procedure
with attention to the following points:

(1) Install the remote release cable to the striker
plate and install the striker plate retaining bolts and
washers to the lines made on dismantling.

Tighten the retaining bolts to just over finger
tight.

Close the lid ensuring that the striker has
actuated the locking mechanism. Check the alignment of the luggage compart-
ment lid in its opening an d adjust the locking action
by moving the striker plate. Tighten the retaining
bolts securely.
When the striker plate is adjusted correctly
pull the remote release ca ble towards the right hand
side of the vehicle until the cable end has 0.5-1.5 mm
clearance and tighten the re taining screws. Check the
operation of the remote release cable and readjust if
necessary.
Installed view of the luggage compartment lid hinge.

236 Body

top of the dashboard rearwards and maneuver the
dashboard through the front door opening.

Installation is a reversal of the removal procedure
with attention to the following points:

With the aid of an assistant, ensure that the
outer edges of the dashboard engage properly with the
door pillar brackets.
Hold the dashboard in position and loosely
install all retaining bolts. Align the dashboard
and
tighten all screws and bolts securely.
10. SEAT BELTS

The front and outer rear seats are equipped with
lap/sash inertia reel seat belts, which are designed to
lock with any sudden change in vehicle motion.

The centre rear seat is equipped with a manually
adjustable lap seat belt.

Child restraint anchorages are located on the
parcel shelf behind the rear seat on Sedan models and
at the rear of the lugg age compartment floor on
Hatchback models. These anchorages must be used if
a child's seat or capsule is installed to the vehicle. The
anchorages should not be used for adult scat bells or
harnesses.

The seat belts should be periodically inspected as
described below. Any seat belt assembly that is worn
or damaged, or has been subjected to abnormal
loadings in a collision, should be renewed as a
complete assembly.

Only mild soap and water should be used to clean
the webbing. Contamination wi th polish, oil, bleaches
and other chemicals should be avoided.

TO INSPECT
(1) Check the seat belt webbing for fraying, cuts,
burns or other damage. On inertia reel belts, slowly
pull the belt from the reel to allow the entire length to
be examined. If the webbing is damaged or worn,
renew the seat belt assembly.


Check the seat belt webbing for fraying, cuts, burns or
other damage.
Ensure that the belts are not twisted.
Check all retaining nuts and bolts for secu-
rity.
Inspect the belt buckles for correct and
secure engagement. If the buckles are damaged or do
not function correctly, renew the seat belt assembly. On inertia reel seat belts, check the retractor
mechanism as follows:
Pull the belt slowly from the reel and check
for smooth operation. Release the belt and ensure that
it retracts fully.
Pull the belt rapidly from the reel. The reel
should lock.
Drive the vehicle at walking pace and at-
tempt to withdraw the belt slowly while braking
sharply. The reel should lock. If the retractor mechanism does not function
correctly, renew the seat belt assembly.

11. SEATS
FRONT SEAT
To Remove and Install
Adjust the seat to the most forward position.
Remove the mounting bolts from the rear of
the seat.
Adjust the seat to allow access to the mount-
ing bolts at the front of the seat. Remove the mounting bolts and withdraw
the seat from the vehicle.
Installed view of the fron t seat belt with the door pillar
trim removed showing the mounting points.

Body 237


Installed view of the front seat mounting bolts.
Installation is a reversal of the removal procedure
with attention to the following points:

Lubricate the seat slides with multi-purpose
grease prior to installation of the seat.
Install all mounting bolts by hand prior to
tightening the mounting bolts securely.
REAR SEAT CUSHION

To Remove and Install
Firmly bump the lower front of the seat
cushion rearwards and up lo release the retaining clips
from the vehicle floor panel.
With the retaining clips released, lift the
front of the seat cushion and release the rear mounting
wires. (3) Lift the rear seat cushion out of the vehicle.
Installation is a reversal of the removal procedure

with attention to the following points:
Position the centre seat belts on top of the
rear seat cushion prior to in stallation of the cushion.
Ensure that the clips at the forward edge of
the seat cushion are proper ly engaged in the floor
panel.
REAR SEAT BACKREST

To Remove and Install
Fold the rear seat backrest forward.
Remove the outer seat backrest hinge bolts.
Pull each backrest to wards the door and off
the centre hinge pins. Remove the rear seat backrest from the
vehicle. Installation is a reversal of the removal procedure.

12. VEHICLE CLEANING
CLEANING THE EXTERIOR
In order to remove dirt and road grime and thus
preserve paint finish, vehicles in continuous use
should be washed at least once a week.

Before washing the paintwork, it is good policy to
first hose all dirt from the underbody and clean out
the drain holes in the doors and sill panels.

Hose the vehicle to remove as much grit as
possible and wash using a clean chamois or sponge,
ensuring that the chamois or sponge is free from dirt
or grit which could scratch the paint surface.

Avoid washing the vehicle in bright sunlight with
high temperature as this will give the paintwork a
streaky watermarked finish.

If necessary, wash the vehicle using a reputable
brand Wash and Wax liquid. The Wash and Wax
liquid will restore the paint luster and leave the
paintwork with a protective coating of wax.

After a period it may become necessary to polish
the vehicle in order to remove built up foreign matter
and give the paintwork maximum protection from
industrial fall-out and salt from sea air etc. Before
polishing the paintwork, always wash the surface to
remove as much road grime as possible. When
polishing follow the polishing instructions which come
with the polish.

NOTE: Grease, oil or tar on the paint
surface can be removed with a little kerosene
or white spirits. To prevent staining, wash
and polish the affected area as soon as the
grease, oil or tar is removed.

CLEANING VINYL TRIM
To maintain the vinyl interior trim in good
condition it should be regularly vacuumed to remove
loose dirt and then wiped with a dry or damp cloth.

If the trim is soiled or stained, the following
cleaning procedure is recommended:

Using warm water, cheese cloth and a mild
soap, thoroughly wash the affected areas.
Repeat the operation using damp cheese
cloth only.
To complete the cleaning operation wipe the
trim over with a dry piece of cheese cloth.
NOTE: If the interior trim is badly soiled or
stained, wash with a reputable brand of
upholstery cleaner care fully following the
makers instructions.

CLEANING CLOTH TRIM
Loose dirt and dust on cloth trim should be
removed with a vacuum cleaner or a very soft brush.
Do not use a whisk brush or any other type of coarse
brush or damage to the cloth could result. If the fabric
is soiled the following cl eaning procedure is recom-
mended.

Sponge the fabric ligh tly with warm water
containing a little detergen t and household ammonia.
After sponging, rub the fabric lightly. If
soiling is still apparent, re peat the sponging operation.
Use a clean dry cloth to soak up excess fluid.