1987 NISSAN PULSAR battery

218 Electrical System
Connect a jumper lead from the negative
terminal of a 12 volt battery to the earth wire. Connect a jumper lead from the positive
terminal of a 12 volt battery and connect each of the
trailer lamp wires in turn to the positive battery terminal jumper lead, noting the color of the wire
and the lamp circuit operated.

(3) After installation, connect the trailer plug to
the socket on the vehicle and check for correct lamp
operation.


Vehicle and trailer wired to conform to Australian Standard AS2513. Sockets and plug shown are as viewed
from the terminal side of the component. Refer to the text for the correct terminal applications when using a
5 or 6 pin socket and plug.

COLOUR CODE
B - Black
G - Green
L - Blue
N - Brown
R - Red
W - Whlte
Y -Yellow

1 To vehicle wiring 7.Trailer reverse lamp

harness 8.Trailer L H turn signal
2. 7 pin socket — Bosch. lamp

Hella. Utilux 9.6 pin socket - Utilux
3 7 pin plug - Bosch, 10.5 pin socket - Bosch

Hella, Utilux Hella
4. Trailer R H turn signal 11.7 pin socket - Brylite

lamp 12.Trailer electric brakes
5. Trailer tail lamp
6. Trailer stop lamp

Electrical System 219


Wiring diagram (WDI) for the starting, charging and engine management systems.
COLOUR CODE
The first letter of the code
represents the main wire color,
the other letters represent the
trace colors.

B - BLACK
L - BLUE
G - GREEN
R - RED
Y - YELLOW
W - WHITE
N - BROWN
O - ORANGE
K - PINK
S - GREY V - VIOLET
P - PURPLE X - LIGHT GREEN
Z - LIGHT BLUE
M - DARK GREEN
T - DARK BLUE
A - LIGHT BROWN
E - SLATE
D - TAN

KEY 1. Battery
2. Fusible links
3. To BATT WD4
4. Alternator
5. Starter motor
6. To No 27 WD2
7. Ignition switch
8. To No.10 WD4
9. To ECU BIO
10. Inhibitor relav
11. Neutral safety
switch
12. Fuse No.8 Ignition
13. Ignition coil
14. Distributor
15. To ECU A1
16. Fuel pump relay
17. Fuel pump
18. ALDL connector - Terminal G
19. Oil pressure switch
20. To No. 19 WD2
21. To No. 4 WD2
22. Reverse lamp switch
23. Fuse No. 9 Ignition
24. L H reverse lamp
25. R H reverse lamp
26. EGI relay
27. ECU C16 and B1
28. ECU A6
29. To ECU D16
30. To ECU D15
31. Injectors
32. Ignition relay
33. To No. 1 WD2
34. To tachometer
35. Condensor
36. Bypass circuit (manual transaxle)

Body 235
lever and remove the screws underneath. Withdraw
the rear console.

On manual transaxle models, unscrew the
gear lever knob and prise out the gear lever rubber
boot. On automatic transaxle models, prise out the
panel around the selector lever and maneuver the
panel over the lever. Remove the screws retaining the front of the
console to the floor panel and withdraw the console
from the vehicle. Installation is a reversal of the removal procedure.

9, DASHBOARD
TO REMOVE AND INSTAL
Disconnect the negative battery terminal.
Remove the centre console as previously
described in this section. Remove the steering wheel as described in
the Steering section. Remove the upper and lower steering col-
umn shrouds and remove the combination switch.
Refer to the Electrical System section if necessary. Remove the retaining screws and withdraw
the lower trim panel from underneath the steering
column. Remove the screws from underneath the
bonnet lock handle and slide the bonnet lock handle
downwards out of the dashboard. Remove the screws retaining the centre fas-
cia panel, two upper and two lower, withdraw the
fascia panel slightly and disconnect the wiring to the
cigarette lighter.

Dismantled view of the centre console assembly. Au-
tomatic transaxle model.
Remove the radio/cassette bracket retaining
screws. Disconnect the aerial and the wiring and
withdraw the radio/cassette from the centre bracket. Remove the heater control knobs and re-
move the heater fascia panel screws. Carefully remove
the heater fascia panel leaving the heater controls in
place.
Loosen the bolt retaining the large wiring
connector at the lower right hand side of the dash-
board. As the bolt is loosened it will force the
connector apart. Using a screwdriver, carefully prise out the
demister ducts from th e top of the dashboard.
Using a suitable socket, remove the bolts
from underneath the demister ducts. Remove the bolts from the outer lower edges
and the lower part of th e centre bracket assembly.
NOTE: Refer to the illustration for the
location of the dashboard retaining bolts.

(14) With the aid of an assistant lift the dash-
board straight up at the door pillar brackets. Tilt the


View of the dashboard removed from the vehicle. The arrows indicate the location of the retaining bolts.