1987 MAZDA 626 torque

1 B INSPECTION AND REPAIR
5. Measure the oil clearance of the camshaft and
camshaft caps.
(1) Remove any oil or dirt from the journals and
bearing surface.
(2) Set the camshaft onto the cylinder head.
(3) Position plasti-gauge on top of the journals in
the axial direction.
76G01B-060
(4) Place the camshaft caps according the cap
number and arrow, and tighten them in the or-
der shown in the figure.
Tightening torque:
18—26 N-m (1.8—2.7 m-kg, 13—20 ft-lb)
76G01B-061
(5) Loosen the camshaft cap bolts in the order
shown in the figure.
76G01B-062
(6) Measure the oil clearance at each cap.
Oil clearance:
0.035—0.085 mm (0.0014—0.0033 in)
Maximum: 0.15 mm (0.0059 in)
(7) If the oil clearance exceeds the maximum, re-
place the camshaft and/ or the cylinder head.
76G01B-063
1B—40

1 B ASSEMBLY (CYLINDER BLOCK)
ASSEMBLY
1. Clean all parts before reinstallation.
2. Apply new engine oil to all sliding and rotating parts.
3. Replace plain bearings if they are peeling, burned, or otherwise damaged.
4. Tighten all bolts and nuts to the specified torques.
Caution
Do not reuse gaskets or oil seals.
CYLINDER BLOCK—I
Torque Specifications
69G01A-139
1B—48

ASSEMBLY (CYLINDER BLOCK) 1 B
76G01B-070
76G01B-071
Connecting Rod
1. Align the identification mark to the cap of large end
of connecting rod and F mark on the piston as
shown in the figure.
2. Apply a coat of engine oil to the circumference of
each piston pin and to the small end of each con-
necting rod.
3. Set a clip into the clip groove in one side of the
piston.
4. Insert the piston pin into the piston and connect-
ing rod from the opposite side of the piston with
the SST .
5. Tap the piston pin in until it touchs the clip. Install
the other clip into the groove in the piston.
6. Check the oscillation torque of the connecting rod.
(Refer to page 1B—33.)
Piston Ring
1. Install the three-piece oil rings on the pistons.
(1) Apply engine oil to the oil ring spacer and rails.
(2) Install the oil ring spacer so that the opening
faces upward.
(3) Install the upper rail and lower rail.
Note
a) The upper rail and lower rail are the same.
b)Each rail can be installed with either face
upward.
69G01A-144
1B—49

ASSEMBLY (CYLINDER BLOCK) 1 B
Oil clearance inspection
(1) Remove any foreign material and oil from the
journals and bearings.
(2) Install the upper main bearings in the cylinder
block.
(3) Set the crankshaft into the cylinder block.
(4) Position the plasti-gauge on top of the journals
in the axial direction.
86U01X-122
(5) Install the main bearing caps along with the
lower main bearings according to the cap num-
ber and mark.
(6) Tighten the caps in two or three steps in the
order in the figure.
Tightening torque:
82—88 Nm (8.4—9.0 m-kg, 61—65 ft-lb)
Caution
Do not rotate the crankshaft when measuring
the oil clearances.
86U01X-123
(7) Remove the main bearing caps, and measure
the plasti-gauge at each journal at the widest
point for the smallest clearance, and at the nar-
rowest point for the largest clearance.
If the oil clearance exceeds specification, grind
the crankshaft and use undersize main bear-
ings. (Refer to page 1B—45.)
Oil clearance
No. 1, 2, 4, 5:
0.025—0.043 mm (0.0010—0.0017 in)
No. 3:
0.031—0.049 mm (0.0012—0.0019 in)
Maximum: 0.08 mm (0.0031 in)
Apply a liberal amount of engine oil to the main
bearings and main journals.
Install the crankshaft and the main bearing caps
according to the cap number and ^ mark.
86U01X-125
1B—51

ASSEMBLY (CYLINDER BLOCK) 1 B
Connecting Rod Cap
1. Check the connecting rod bearing clearances us-
ing the same procedure as used for the main bear-
ing oil clearance.
Connecting rod cap tightening torque:
69—73 Nm (7.0—7.4 m-kg, 51—54 ft-lb)
Oil clearance:
0.027—0.067 mm (0.0011—0.0026 in)
Maximum: 0.10 mm (0.0039 in)
76G01B-076
Caution
Align the alignment marks on the cap and on
the connecting rod when installing the con-
necting rod cap.
2. If the oil clearance exceeds specification grind the
crankshaft and use undersize bearings. (Refer to
page 1B—46.)
76G01B-077
3. Check the side clearance of each connecting rod
without the cap installed.
Side clearance:
0.110—0.262 mm (0.004—0.0103 in)
Maximum: 0.30 mm (0.012 in)
If the clearance exceeds the maximum, replace the
connecting rod.
69G01B-139
4. Apply a liberal amount of engine oil to the crank-
pin journal and connecting rod bearing.
5. Install the connecting rod cap with the alignment
marks aligned.
Tightening torque:
69—73 Nm (7.0—7.4 m-kg, 51—54 ft-lb)
76G01B-078
1B—53

1 B ASSEMBLY (CYLINDER BLOCK)
CYLINDER BLOCK—II
Torque Specifications
19—25 N m (1.9—2.6 m-kg, 14-19 ft-lb)
7—12 N'm (70—120 cm-kg, 61—104 in-lb)
69G01A-166
Rear Cover
1. Apply engine oil to the rear cover, oil seal and oil
seal lip.
2. Press the oil seal into the rear cover.
4BG01A-158
1B—54

ASSEMBLY (CYLINDER BLOCK) 1 B
3. Install the rear cover and a new gasket.
Tightening torque:
8—12 N-m (80—120 cm-kg, 69—104 in-lb)
86U01X-131
4. Cut away the portion of the gasket that projects out
from the rear cover assembly toward the oil pan
side.
Caution
Do not scratch the rear cover assembly.
86U01X-132
End Plate
Install the end plate.
Tightening torque:
19—30 Nm (1.9—3.1 m-kg, 14—22 ft-lb)
4BG01A-160
Oil Pump
1. Apply engine oil to a new oil pump oil seal and the
oil pump body.
2. Press the oil seal into the oil pump body.
79G01C-085
1B—55

1 B ASSEMBLY (CYLINDER BLOCK)
3. Apply engine oil to the oil seal lip.
4. Remove any dirt or other material from the con-
tact surfaces.
5. Apply a continuos bead of silicon sealant to the
contact surface of the oil pump.
Caution
Do not allow any sealant to get into the oil
hole.
86U01X-133
6. Install a new O-ring into the pump body.
7. Install the oil pump.
Tightening torque

(A):
19—25
N
m
(1.9—2.6 m-kg, 14—19 ft-lb)
(§): 37—52
N
m
(3.8—5.3 m-kg, 27—38 ft-lb)
8. Remove any sealant which has been squeezed
out.
76G01A-137
Oil Jet
Install the oil jet as shown in the figure.
Tightening torque: 12—18 Nm
(1.2—1.8 m-kg, 104—156 in-lb)
Caution
The shapes of the No.1, 3 cylinders jet valves
and No.2, 4 jet valves are different.
76G01B-079
Oil Strainer
Install the oil strainer and a new gasket.
Tightening torque:
8—12 Nm (80—120 cm-kg, 69—104 in-lb)
86U01X-136
1B—56