1987 MAZDA 626 cooling

3B RADIATOR
Note
a) Position the hose clamp in the original location on the hose.
b) Squeeze the clamp lightly with large pliers to ensure a good fit. 86U03X-010
RADIATOR
REMOVAL AND INSTALLATION
1. Drain the engine coolant.
2. Remove in the sequence shown in the figure.
3. Install in the reverse order of removal.
1. Coolant reservoir hose
2. Fast idle solenoid
3. Coolant level sensor connector
4. Cooling fan connector
76G03B-005
5. Upper and lower radiator hose
6. Cooling fan and radiator assembly
7. Cooling fan
INSPECTION
Check the following points. Repair or replace if
necessary.
1. Cracks, damage, or water leakage
2. Bent fins (Repair with a screwdriver)
3. Distorted or bent radiator inlet
86U03X-012
3B-6

3B COOLING FAN
COOLING FAN
SYSTEM CIRCUIT
I
IG1 IG Relay Main fuse
©
Main fan motor
V-f motor
IG1
Water thermo switch OFF: over 91°C (208 °F)
Water thermo switch ON:
below 84°C
(183°F)
76G03B-015
CIRCUIT INSPECTION
1. Turn the ignition switch ON.
2. Disconnect the water thermo switch connector, and
check that the fan begins to operate.
3. If the fan doesn't operate, check the fuse, fan re-
lay, fan motor, thermo switch, and wiring harness.
76G03B-016
3B—10

COOLING FAN 3B
FAN MOTOR
Removal and Installation
1. Remove in the sequence shown in the figure.
2. Install in the reverse order of removal. 86U03X-021
ft—11 N-m (80-110 cm-kg, 69—95 (n-lb)
2.6—5.2 N-m (27—53 cm-kg, 23—46 In-lb)
76G03B-013
1. Cooling fan assembly (Refer to page 3B—6) 3. Fan
2. Cowling 4. Fan motor
Inspection
1. Connect an ammeter and battery to the fan motor
connectors.
2. Check that the fan motor operates smoothly at the
specified current or less.
Current
8.0—11.0 Amperes
3. Replace the fan motor if necessary.
76G03B-014
3B-11

3B COOLING FAN
WATER THERMO SWITCH
1. Remove the cooling fan water thermo switch.
Note
Make sure that the ignition switch is OFF. If
not, the fan will operate when the connector
is removed.
76G03B-017
76G03B-018
2. Place the water thermo switch in water.
3. Heat the water gradually, and check for continui-
ty of the switch with an ohmmeter. Replace if
necessary.
Temperature Continuity
Above
91
°C (208°F) No
Below 84°C (183°F) Yes
4. Install the water thermo switch and a new O-ring.
Tightening torque:
6—9 N-m (60—90 cm-kg, 52—78 in-lb)
Caution
Do not use sealing tape.
3B-12

Fuel filter Solenoid valve *1 Solenoid valve *1
(No.2 purge control) (No.1 purge control)
Separator Three way
Injector
,Distributor
Fuel pump
In-take filter
Air flow sensor
Water thermo sensor
Knock sensor
switches
Intake air thermo sensor
— Water thermo switch *1 __ j—Ig. switch (ST) j_J,—lg. switch (ON) -A/C switch 'A/C magnet clutch P/S switch —Head light switch —Rear defroster switch —Cooling fun switch —Blower switch —Neutral and clutch
O) <
{/> H m
g >
o 3D >
^Throttle sensor *1
Air valve
Solenoid valve
(ISC)
EGR control valve *1
EGR modulator valve *1
0 1 CO
a *1...Unleaded fuel only
*2...Leaded fuel only
Oxygen
sensor *1
One-way check valve
Shutter valve actuator Catalytic
converter *1 Solenoid valve (VIC)
O c
m
o

ISC SYSTEM 4C
76G04C-081
76G04C-082
Cooling fan switch
Rear defroster switch
Head light switch
Blower motor switch
ISC "valve
76G04C-083
(ISC valve)
6. Connect the ISC valve connector.
Note
a) Make sure that the initial idle speed is set
to specification.
b) All accessory must be OFF.
7. Again disconnect the ISC valve connector (engine
at normal operating temperature).
8. Check that the engine speed decreases.
9. Reconnect the ISC valve connector.
10 Remove the jumper wire from the test connector
and make sure that the idle speed is within specifi-
cations.
(Load Test)
11. Apply power steering, electrical, and air conditioner
loads and check that the idle speed is controlled
to within specifications.
Load Idle speed
P/S 750 ± 50
E/L 800 ± 50
A/C 800 ± 50
E/L and A/C 800 ± 50
BAC Valve
Air valve
1. Remove the BAC valve from the throttle body.
2. Blow air through the valve from port A and check
that air comes out of port B when the BAC valve
is cold..
3. If not correct, replace the BAC valve.
Note
Refer to "Installation" on this page for the
BAC valve installation.
86U04A-063
4C—47

4D SUPERCHARGING SYSTEM (RF-CX)
INTERCOOLER
Removal and Installation
1. Remove in the sequence shown in the figure.
2. Install in the reverse order of removal.
3. Check for air leakage.
76G04D-037
5. Front bumper (Refer to Section 14.)
6. Cooling fan
7. Air pipe
8. Intercooler
Inspection
Check the intercooler for cracks or damage. Replace
if necessary.
8—11 N-m (80—110 cm-kg, 69—95 In-lb)
1. Battery
2. Battery carrier
3. Front grille (Refer to Section 14.)
4. Headlight (Refer to Section 14.)
76G04D-038
4D—16

TROUBLESHOOTING (G4A-EL) 7B
7. Perform the stall test for the following ranges in the same manner.
(1) D range (4) L range
(2) D range (Hold) (5) L range (Hold)
(3) S range (Hold)
Caution
Be sure to allow sufficient cooling time between each stall test.
Engine stall speed: D.S.L range 2170—2270 rpm
R range 2130—2230 rpm
Note
The stall test can be performed with the EC-AT Tester in place of a tachometer.
Drum stall speed indication: 0 rpm
76G0/B-029
Evaluation
Condition Possible cause
Above specification
In all ranges Insufficient line
pressure
Worn oil pump
Above specification
In all ranges Insufficient line
pressure Oil leakage from oil pump, control valve, and/or transmission case
Stuck pressure regulator valve
Above specification
In forward ranges Forward clutch slipping One-way clutch 1 slipping
Above specification
In D range One-way clutch 2 slipping
Above specification
In S (Hold) and L (Hold) ranges Coasting clutch slipping
Above specification In D (Hold) and S (Hold) ranges 2-4 brake band slipping Above specification
In R, L and L (Hold) ranges Low and reverse brake slipping
Above specification
In R range
Low and reverse brake slipping Reverse cluch slipping Perform road test to determine whether problem is low and reverse brake or reverse clutch
a) Engine brake applied in 1st ...Reverse clutch
b) Engine brake not applied in 1st ...Low and reverse brake
Within specification All shift control elements within transmission are func-
tioning normally.
Below specification
Engine out of tune
Below specification One-way clutch slipping within torque converter
86U07B-036
7B-29