1986 TOYOTA LAND CRUISER tow

BE0N7-06
BE4671
Antenna Nut
BE5781
BE5780
BE4674
Twist
- BODY ELECTRICALANTENNA
BE-177
2550 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REPLACEMENT
1. Auto antenna models:
REMOVE ANTENNA ROD
HINT:
Do this operation with the battery negative (-) cable connected
to the battery terminal.
(a) Remove the antenna nut.
(b) Turn the radio switch ºONº position.
(c) Turn the antenna switch to ºUPº.
(d) Catch the antenna rod by hand and turn the radio switch
ºOFFº.
(e) Try again to turn the radio switch ºONº and antenna switch
ºUPº.
(f) Remove antenna rod.
HINT:
The rod will extend fully and be released form the motor anten-
na.
NOTICE:
To prevent body damage when the antenna rod is released,
hold the rod while it comes out.
2. Auto antenna models:
INSTALL ANTENNA ROD
(a) Insert the cable of the rod until it reaches the bottom.
HINT:

When inserting the cable, the teeth on the cable must face
toward the rear of the vehicle.

Insert the antenna approx. 350 mm.
(b) Turn the radio switch to ºOFFº.
HINT:

In case the cable is not wound, twist it, as shown in the
illustration.

Even if the rod has not retracted fully, install the antenna
nut and inspect the antenna rod operation. It will finally re-
tract fully.
(c) Inspect the antenna rod operation by pushing the radio
wave band select buttons.

I25270
IG1 No.1 Relay
MIR HTR Relay
RR HTR Relay
FR FOG Relay
TAIL Relay
PANEL Relay MIR HTR Fuse
RR HTR Fuse
BLK CTRL Fuse
TOWING Fuse
HEAD CLNER Fuse
FR FOG Fuse
TAIL Fuse
PANEL Fuse
TOWING TAIL Fuse
NV IR Fuse
47 1B
60 1A
50 1B
66 1B
48 1B
70 1B
71 1B
52 1B
57 1B
61 1B
72 1B
63 1A
62 1A
64 1A
59 1B
51 1A
50 1A
59 1A
49 1A
58 1A
60 1B
62 1B
58 1B
64 1B
67 1B
63 1B
69 1B
49 1B
40 1B
39 1B
45 1B
56 1B
55 1B
44 1B
43 1B
41 1B
42 1B
37 1A
36 1A
43 1A
42 1A
44 1A
35 1A
34 1A
45 1A
52 1A
41 1A
63 1AShort Pin
53
21
53
21
53
21
53
21
53
21
53
21
46 1A
46 1B
48 1A
56 1A
68 1B
55 1A
53 1B
40 1A
38 1B
47 1A
37 1B
54 1A
51 1B
61 1A
54 1B
2 1C
- BODY ELECTRICALPOWER SOURCE
BE-17
2390 Author
: Date
:
2004 LAND CRUISER (RM1071U)

- BODY ELECTRICALPOWER SOURCE
BE-19
2392 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(a) Remove the fuse from the junction block and inspect the
connector on junction block side.
Fuse Tester connectionConditionSpecified condition
TOWING 1 - GroundConstantBattery positive voltage
MIR HTR 3 - GroundConstantBattery positive voltage
RR HTR 5 - GroundConstantBattery positive voltage
HAZ-TRN 7 - GroundConstantBattery positive voltage
ALT-S 9 - GroundConstantBattery positive voltage
NV-IR 13 - GroundConstantBattery positive voltage
FR FOG 13 - GroundConstantBattery positive voltage
BRK CTRL 15 - GroundConstantBattery positive voltage
HEAD CLNER 17 - GroundIgnition switch ONBattery positive voltage
FR-IG 19 - GroundIgnition switch ONBattery positive voltage
PANEL 21 - GroundLight control switch HEAD or TAILBattery positive voltage
TOWING TAIL 23 - GroundLight control switch HEAD or TAILBattery positive voltage
TAIL 25 - GroundLight control switch HEAD or TAILBattery positive voltage
BAT 29 - GroundConstantBattery positive voltage
TEL 31 - GroundConstantBattery positive voltage
AMP 33 - GroundConstantBattery positive voltage
EFI or ECD NO.1 35 - GroundConstantBattery positive voltage
AM2 37 - GroundConstantBattery positive voltage
ETCS 39 - GroundConstantBattery positive voltage
HORN 41 - GroundConstantBattery positive voltage
HEAD LH-UPR 51 - GroundLight control switch HI or FlashBattery positive voltage
HEAD RH-UPR 49 - GroundLight control switch HI or FlashBattery positive voltage
HEAD LH-LWR 47 - GroundLight control switch HEADBattery positive voltage
HEAD RH-LWR 45 - GroundLight control switch HEADBattery positive voltage
ST1 1 - GroundConstantBattery positive voltage
AHC 1 - GroundConstantBattery positive voltage
ABS NO.1 1 - GroundConstantBattery positive voltage
ABS NO.2 1 - GroundConstantBattery positive voltage
STARTER 1 - GroundConstantBattery positive voltage
If the circuit is not as specified, inspect the circuits connected
to other parts.
(b) Remove the relay from the junction block and inspect the
connector on junction block side.
Relay Tester connectionConditionSpecified condition
AHC 1 - GroundIgnition switch ONBattery positive voltage
ABS SOL 1 - GroundIgnition switch ONBattery positive voltage
ABS MTR1 1 - GroundConstantBattery positive voltage
ABS MTR2 1 - GroundIgnition switch ONBattery positive voltage
STARTER 5 - GroundConstantContinuity
STARTER 2 - GroundIgnition switch ONBattery positive voltage
EFI or ECD 3 - GroundConstantBattery positive voltage
C/OPN SPIL VLV 5 - GroundConstantBattery positive voltage
C/OPN SPIL VLV 2 - GroundIgnition switch ONContinuity

I24921
Fuses:
1. TOWING
2. MIR HTR
3. RR HTR
4. HAZ-TEN
5. ALT-S
6. NV-IR
7. FR FOG
8. TOWING BRK
9. HEAD CLNER
10. FR-IG
11. PANEL
12. TOWING TAIL
13. TAIL
14. -
15. BAT
16. TEL
17. AMP
18. EFI or ECD NO.1
19. AM2
20. ETCS
21. HORN
22. HEAD RH-LWR
23. HEAD LH-LWR
24. HEAD RH-UPR
25. HEAD LH-UPR
26.STARTER
27. GLOW
28. ST1
29. AHC
30. ABS NO.1
31. ABS NO.2
Relays:
A. AHC
B. ABS SOL
C. ABS MTR1
D. ABS MTR2
E. STARTER
F. EFI or ECD
G. C/OPN
H. F/PUMP
I. HTR
J. IG1 NO.1
K. MIR HTR
L. RR HTR
M. FR FOG
N. TAIL
O. PANEL
P. CDS FAN
Q. MG CLT
R. W/TEMP CUT
S. HEAD
T. HEAD HI
U. HORN
A
1
B CD
E F
G
H I
J
KL
MN O
P
RST
U Q
2 3 4 5 6 7 8 9 10 11 12 13
14 15 16 17 18 19 20 21 22 23 24 25 26
2728 29 30 31
Engine Room R/B BE-12
- BODY ELECTRICALPOWER SOURCE
2385 Author
: Date
:
2004 LAND CRUISER (RM1071U)

BE2E2-01
I25791
Cowl Side J/B LH

BATT CHARGE FuseEngine Room R/B

TOWING Fuse

TOWING TAIL Fuse
Towing Converter Relay
(Located inside of the quarter trim panel LH)Trailer Socket
BE-200
- BODY ELECTRICALTRAILER TOWING
2573 Author
: Date
:
2004 LAND CRUISER (RM1071U)
TRAILER TOWING
LOCATION

BE2F2-01
I20790
Key Plate Inserted
ON
OFFWithin. 5secs.
1 Key Plate Not Inserted
23 910Within. 30secs.
Once 9 times BE-100
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
2473 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSPECTION
1. CHARACTERS OF WIRELESS DOOR LOCK
(a) The operation distance changes according to how cus-
tomers hold the transmitter or where it is used.
(b) Because of using the very weak radio wave, if there is a
strong wave or noise on the frequency being used, the op-
eration distance may become shorter.
2. WIRELESS DOOR LOCK BASIC FUNCTION
(a) Stand on the driver's side. Stay 1 m away from the ve-
hicle.
(b) Turn the transmitter toward the vehicle and press any one
of the transmission switched for 1 sec.
3. INSPECT WIRELESS DOOR LOCK DIAGNOSIS MODE
(a) Start up diagnosis mode.
HINT:
Follow the method below.
(1) Insert the ignition key into the ignition key cylinder.
(2) Remove the ignition key from the ignition key cylin-
der.
(3) Insert the key into the ignition switch.
(4) Turn the ignition switch ON once within 5 sec.
(5) Repeat turnning the ignition switch OFF " ON 9
times within 30 sec.
(6) Enter the diagnosis mode, and make sure that the
taillight lights up.
(b) Finishing the Diagnosis Mode.
During the Diagnosis mode, turn the ignition switch OFF
" ON to go back to the normal mode.
At this time make sure that the taillight lights up.

BE0CI-07
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE-99
2472 Author
: Date
:
2004 LAND CRUISER (RM1071U)
PRE-CHECK
1. CHARACTERS OF WIRELESS DOOR LOCK
(a) The operation distance changes according to how customers hold the transmitter or where it is used.
(b) Because of using the very weak radio wave, if there is a strong wave or noise on the frequency being
used, the operation distance may become shorter.
2. WIRELESS DOOR LOCK BASIC FUNCTION
(a) Stand on the driver's side. Stay 1 m away from the vehicle.
(b) Turn the transmitter toward the vehicle and press any one of the transmission switched for 1 sec.

BO1J7-03
Spare Wheel
Carrier No.1 Lid
H18902
: Specified torqueN´m (kgf´cm, ft´lbf)
Rear Bumper Step Reinforcement
Extension
Mounting
Bracket
Rear Bumper CoverExtension Mounting Bracket
Reflex Reflector
4.9 (50, 43 in.´lbf)
19 (195, 14)
4.9 (50, 43 in.´lbf)
20 (204, 15)
20 (204, 15)
20 (204, 15)
Reflex Reflector
19 (195, 14)
Rear Bumper Lower Cover
12.5 (127, 11)
12.5 (127, 11)
20 (204, 15)
w/ Tow Hitch Receiver
Tow Hitch Receiver
85 (867, 63)
HINT:
REMOVAL: Remove the Tow hitch receiver
after loosening the rear bumper cover.
INSTALLATION: Install the Tow hitch receiver
after installing the rear bumper cover temporarily.
Rear Bumper Reinforcement20 (204, 15)
20 (204, 15)
85 (867, 63)
- BODYREAR BUMPER
BO-5
2579 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REAR BUMPER
COMPONENTS