1984 NISSAN 300ZX window

BODY
I
SECTION BF
CONTENTS
GENERAL SERVICING . . ............ .... ..... BF- 2
BODY END AND DOOR .. ...... .......... BF- 6
INSTRUMENT
........ ........ ..... . . BF-49
SEAT
... .. ........ .. ..... . BF-50
SEAT BELT
. .... ... ......... . . BF-57
TRIM AND MOLDING
.. ... .. . . BF-58
WINDSHIELD AND WINDOWS
...... ... .............. BF-63
T-BAR ROOF
........ ...... .. ......... BF-68
MIRROR
...... ... ... .. .... .. . . BF-69
REAR COMBINATION LAMP
........ .............. BF-70
BODY ALIGNMENT
.... ..... ... ... BF-71

BODYENDANDDOOR
Front Door (Cont'd)
POWER WINDOWIWI RING DrAGRAM
(White)
HARNESS POWER WINOOW SUB SWITCH IAssistI --Ass161 MAIN HARNESS LIY-
BATTERY (Via fusible link1
POWER WINDOW
MOTOR IAssirtl
LIY
POWER WINDOW
MOTOR IDriverI
(Driver) LN -
IGNITION SWITCH
ON or START
IGNITION RELAY
w CIRCUIT BREAKER
lured together with power seat1
To engine room harness (Ground)
HARNESS DOOR HARNESS
SBF408B
power door lock actuator POWER DOOR LOCK/WIRING DIAGRAM
FUSE BLOCK
u
I
I L
To engme room - harness IGroundl
.
Power door lock switch
MAIN DOOR HARNESS HARNESS -Driver
SBF409B
BF-I 1

t IGNITION SWITCH I ON or START
IGNITION RELAY 35M
Big;
(For power window and
CIRCUIT
BREAKER
power seat)
To engine room harness L (Ground1
!
t B
,,-CIRCUIT BREAKER
M [ I
r CIRCUIT BREAKER SEAT SWITCH ~~ (Seat Ilfter. sllde. reclining and
thigh support1
Seat cushion ground
- CIRCUIT BREAKER
in harness
LD m ll W (D W m
SEAT BACK SWITCH
RTR AIR PUMP MOTOR
Seat cushion ground
IRiI
CIRCUIT BREAKER Seat curhian ground -

TRIM AND MOLDING
Exterioi
@ Sill molding
Front and rear ends of molding are fixed with double-faced
.When affixing the portion, heat body panel and moldlng
to adhesive tape
30 to 40'C I86 to 104'FI with a heat gun, and then innall gt
8 Drip molding
Body panel
SBF400B
0 Windshield upper & side molding
Molding fastener
(Set It when windshield glass IS installed I
Double-faced
adherive tape
[When
in-
tener, heat
body Panel
and fastener Otalllng far-
SBF401B
:ont'd)
@ Windshield lower molding
SBF402B
@ Side window molding
Refer to Side Window
@ Back door weatherstrip
Attach the weatherstrip by aligning each white
marking with the center of each back door
hinge
rsodv panel
Weatherstrip
When mstalltng.
carefully avoid
rolling and
-1 LAttach securely
Trim
SBF403B
0 Rear panel outer finisher
(Fwed wth double faced adhesive tape) SBF404B
BF-61

WINDSHIELD AND WINDOWS
Windshield
REMOVAL
After removing moldings. remove
glass
I Cutting sealant /I
CAUTION Be careful not to scratch glass when
removing
INSTAL LATl ON
Use genuine Nissan Sealant kit or equivalent Follow instructions furnished
with it
After installation, the vehicle should remain stationary for about 24 hours
Do not use sealant which is more than 12 months past its production date
Do not leave cartridge unattended with its cap open
Keep Primers and sealant in a cool, dry place Ideally, sealant should be stored
in a refrigerator
WARNING
Keep heat or open flames away as Clean banding surface thoroughly -1 Primers are flammable
I Glass side
Body stde
,m SEF4136
i-- Bod; side Glass'side
-- 4 nstall molding fastener When inrtalling it. heat body panel and
fastener to approx 30 to 40'C (86 to
Side Molding Fastener
SBF414B
I - .
Apply primer E
S E F038 B
Allow Primers to dry for 10 to 15
minutes before proceeding to the next
CAUTION
step
T Install dam rubber
8 mrn 10 31 in) 5EF415B
I
Apply primer A
&&$P& 11111
SEFO39B I
CAUTION.
Do not apply Primer A to windshield
I opening flanges
@
BF-63

WINDSHIELD AND WINDOWS
Windshield (Cont'd)
Relative humidity
90 50
Temperature OC (OF)
I v
lnstall spacers to panel wlth double-faced tape
surfaces until sealant has properly
25 vulcanized
Vehde center
3oo 111 Unit rnm (in1 SBF416E
Apply sealant evenly
Approximately
8 10 311
L Glass L Approximately
11 1043) Untt rnm (in1 SBF417B
I CAUTION
Windshield glass should be installed
within 15 minutes of applying sealnt
sealant starts
to harden 15 minutes
after
it is applied
Set glass in position and
. press glass lightly and evenly
1
Set moldings
k-J
Check for water leakage
Install molding
25 (77) I 16 I 29 1 61
BF-64

WINDSHIELD AND WINDOWS
Back Door Window
Attach the lower moldmg to the glass before installmg the glass.
Attach the glass stopper (glass upper portion) and the slde molding grommet to the panel before install-
ing the
glass
The remaining procedure for removal and lnstallatlon IS the same as that for the windshield.
//[ Upper molding
Glarr - ,
Lower molding
I 1 5 mrn 10.059 In1
Back door Panel
'L GI~~S stopper IAt hing center)
SSF419B
BF-65

WINDSHIELD AND WINDOWS
Side Window
When innalling glass. assemble molding to glass.
fhen insla11 glass with butyl seal and nuts
lnrlde of center pillar (After removing rear upper frlm. loosen I1 1
i 7nn
Do not add too much as 11 will ooze out
[Refer to GENERAL
SERVICING
1
Inride of rear pol
Glarr
Sealant Do not add loo much as 11 wtll ooze out
Molding
SBF418B Umt mm Id
BF-66