1981 CHEVROLET MONTE CARLO maintenance schedule

Downloaded from www.Manualslib.com manuals search engine JACKING
CAUTION
To help avoid personal injury:
• Follow air jacking and stowage instructions.
• Use jack only for lifting this vehicle during wheel change.
• Never get . beneath the vehicle, start or run engine while vehicle is supported by jack.
• Always securely restol" sp!.re tire (orflattire) and all jac king equipment.
Wheel Nut Torque .
CAUTION: As soon as possible atter installing a wheel -AND at the intervals stated
In Section 'S of the Maintenanc," Schedule folder --have a technician tighten wheel nuts with a torque wrench to the specifications shown in "Specifications," Section 7 of this manual.
Wheel nuts should be tightened alternately and evenly to the correct torque.
Never use oil or grease on studs Of nuts.. Jrnproperty tightened wheel nuts could eventually aUow the whee! to come off while the veNeta Is moving, -po$$rbty causing
personal injury , damage and/or klss of c_ontrol. (Also see the "Replacement Fasteners" Caution In "Service and Maintenance ," Section 5 01 this m8nu81 regarding the danger of mixing metric and custom,sry fasteners. And, see the "Replacement Fasteners " Caution
under "Tires" in the same seclion regarding the importance of obtaining good metal-to­
metsl contact.)
Stowage ·of. Tire . and .!aC;.k,. . .
CAUTION: Always securely restow the spare tire assembfy (or nat tire), all jacking equipm ent, any tire inflator, and any covers or doors, using the means provided. This will help keep such things from being thrown about-and injuring people In the vehicta d.Ufing a sudden maneuver or an accident.
Before stowing
the tire, be sure:to clean the tire well 01 anything that would keep the tlr. from resting on the bOttom of the well. To stow the jack, place its lever in the "UP" position and. move the handle back and forth until the column is ·secure in the receiver (see Illustration). If these steps are not taken, the tire or lack may push against the trunk lid so thai the trunk lid cannot seal tightly. This _ may allOw carbon monoxide from the '. exhaust system -to get _inside tiMt c • . ttvougtl the trunk. (See "Engine -Exhaust Gas Caution (CaroonMonoxkle) " al the beginning of "Starting and Operating,'; Section 2 of this manual .)
Extended Vehicle Storage
If you plan to store your vehicle over an extended periOd of time, certain steps
should be taken to give it maximum protection.
It is recommended that you
write the Chevrolet Motor Division , General Motors Corporation, Consumer
Relations Dept., Warren , Michigan
48090, for detailed instructions on how to
prepare your vehicle for storage .
3-7

Downloaded from www.Manualslib.com manuals search engine SECTION 5
SERVICE AND MAINTENANCE
CAUTION: As with any mletdne, take car. when making any check, doing any maintenance, or making any repair, to avoid being Injured. Note that some of the materials in this vehicle may be hazardous if used, serviced , or handled improperly. Improper or incomplete servl'c. could alao lead to the vehicle ItMn not working properly which may resuH in personal Injury, or damage to the vehicle or its equipment. n you holy. any question about carrying out some service, hoIv. the service done by a skilled technician.
REPLACEMENT FASTENERS
During vehicle maintenance , any fasteners used to replace older ones must
h ,ave the same measurements and strength as those removed, whether metric or customary. (The numbers on the heads of metric bolts and on the surface s
of metric nuts show their strength . Customary
bolts use radial lines to show
thi s,
while most customa ry nuts do not have strength markings.) Fasteners
taken from the vehicle should be saved for re-use in the same spot when
possible . Where a fastener cannot be used again, take care to choo se a
repla cement that matches the old one. For information and help , see your dealer. .
CAUTION: This vehicle has some parts dimensioned in the metric system as well .. in the customary system. Some fasteners are metric and are very close in dimensnion to well· known customary fasteners in the inch system. Mismatched or incorrect fasteners
can result tnda~tp ~ vehic" or possibly personal Injury.
MAINTENANCE SCHEDULE AND WARRANTY
FOLDERS
For owner convenience, a separate folder has been provided with your vehicle which contains a complete maintenance schedule. It also briefly describes the
safety I emission control, lubrication and general service your vehicle requires.
The Maintenance Schedule folder is supplemented by this section of the
Owner 's
Manual.
Two Warranty Folders are also furnished with your Vehicle. These provide
detailed information on the :
• t981 Chevrolet New Vehicle Lim ited Warranty
• 1981 Chevrolet Perforation From Corrosion Limited Warranty
• 1981 Emissions Control Systems Warranties, including:
•
Emission Components Defect Warranty
• Emission Pertormance Warranty
• 1981 Chevrolet Powertrain Lirnited Warranty -Power Protection Plus
Read all four publications for a full understanding of your vehicle 's
maintenance needs.
You can get a replacement Maintenance Schedule from your dealer or send
the
VIN (or serial numbe r) of your vehicle to Consumer Relations, Chevrolet
Cent ral Office, Chevrolet Motor Division, Warren, Michigan 48090.
5-1

Downloaded from www.Manualslib.com manuals search engine FUEL CAP
The fuel cap is.behind the. rear license plate.
NOTICE: tt you need: to repWce the fuel cap, use only a cap with these same features as specifie your dealer.
The fuel tank filler cap has a "screw-on ratcheting type" feature .
• _ To remove -rotate cap counterclockwise to clear the inside of the filler
neck. This will allow any residual pressure to escape .
_ To install -reverse this procedure and tighten cap securely until a
"ratcheting ". clicking sound is heard indicating cap is on properly.
CATALYTIC CONVERTER
.Ttle .cal;!ly:tic converter is an emission control device added to the exhaust system,' to reduce exhaust gas pollutants. The converter contains
a ceramic material coated with noble metal catalysts. To prevent contamination
of the catalysts , unleaded gasol;"" must be used . Unleaded gasoline also
reduces spark plug louling. exhaust system corrosion and engine oil
deterioration.
The catalytiC converter requires the use of unleaded gasoline. Using leaded gasoline wilt cause --the converter to lose its effectiveness as an
emission control device. Leaded gasoline will also damage the Computer
Command Control, system oxygen sensor, which could affect emission control,
fuel economy . and drivability.
~,~.,y..'~,","~ ... :..., To help 'prevent damage:
1. Keep your engine properly maintained . Engine malfunctions involving the electrical, carburetion or ignition systems may result in unusually high
catalytic con verter and exhaust . sy~tem temperatures which, under
extreme malfunctioning conditions·, may ignite interior floor:"'covering
materials above the converter. Do not keep driving your vehicle if you
detect engine misfire, noticeable loss of performance ,or other unusual operating conditions. Instead. have it serviced promptly.
A properly maintained
engine will help avoid malfunctions that could damage
the converter.
~ will also help provide good emission control and fuel economy.
See the Maintenance Schedule , folder for information on inspecling and
maintaining the engine. exhaust system. and other components. .
2. Do not drive through or Idle or park your vehicle over combustible
materials, such as grass or leaves_ They could touch the hot exhaust
system and ignite.
3. Do not push or tow this vehiCle to start it. This may result in unusually
high catalytic converter and exhaust system temperatures which under
extreme conditions may ignite interior floor -covering material above the
converter.
Pushing or towing to start can also damage · the catalytic
converter itself.
Disregarding these
instructions could damage the cataly:tic converter. the
vehicle, or nearby property.
5-2

Downloaded from www.Manualslib.com manuals search engine COOL
WARM
Add just enough DEXRO~ II fluid to fill the transmission to the proper level. It
takes only 0.5 liter (one pint) to raise the level from "Add" to "Full" with a hot
transmission.
Automatic Transmission Drain Intervals
Change the transmission fluid and change the filter (or clean the screen) as
outlined
in Section A of the Maintenance Schedule folder.
ENGINE COOLING SYSTEM
Your vehicle has a coolant recovery system. Coolant in the system expands
with heat and overflows into the recovery tank. When the system cools down,
coolant is drawn back into the radiator.
The cooling system was
filled at the factory wrth a quality coolant that meets
GM
Spec~ication 1S99-M . The cooling ·system is designed to use coolant (a
mixture of water and ethylene glycol antifreeze) rather than plain water. The
coolant solution should be used year round.
It has many advantages, such as:
~ provides freezing protection down to -3rC (-34"F) "''''''<~. !'"","."" ' • provides boiling protection up to 12S"C (262"F),
• protects against rust and corrosio~in th~ cooling system,
• maintains the proper engine temperature for efficient operation and
emission control, and
• allows proper operation of the coolant temperature light or gage :
See Section A of the Maintenance Schedule folder to find out when the coolant
must
be ·replaced.
Cooling System Care
Check the c60ling system at regular intervals, such as during fuel stops . You usually do not need to remove the radiator cap to check the coolant level. Lift
the engine hood and look at the "see through" coolant recovery tank. When
the engine is
cold, the coolant level should be at the "Full Cold" mark on the
tank . When the engine has fully warmed . up, the level should be above the
"Full Cold" mark on the tank . If the coolantl6vel is low, remove the cap on the
coolant recovery tank. Add to the recovery tank enough of a 50/50 mixture of
water and a good quality ethylene glycol antifreeze to bring the
level up to the
proper mark. Put the cap back on the recovery tank.
Certain conditions, such
as air trapped in the system, may affect the coolant
level in the radiator. You should check"the coolant level in the radiator at the
time you change the engine
oil and when the engine Is cold. Follow.taps I, S,
9, and 10 under "Coolant Repfacement" for the correct way to remove the
radiator cap and add coolant.
5-6

Downloaded from www.Manualslib.com manuals search engine If you have to add coolant more than four times a year (either to the recovery
tank or to the radiator), see your dealer for a cooling system check.
NOTICE: If you use the proper quality antifreeze, there is no· need to add extra inhihitorsor additiveswtlich claim to improve-the system. They may be harmful to the proper operation of the system.
Cooling' System Service
The cooling system should be serviced at the intervals specified in Section A of
the Maintenance Schedule folder as follows:
1. Wash the radiator cap and filler neck with clean water. See step 1 of "Coolant Replacement" for the proper way to remove the radiator cap.
2. Check the coolant level in the radiator and have it tested for freeze
protection.
Add ethylene glycol antifreeze, if needed, to maintain freeze
protection at-3JOC (~$4°f).
3. Have the cooling system and radiator cap tested for a pressure capacity of 105. kPa (15psi). (The pressure cantle anywhere from 95 kPa, or 14 psi,
to 120
kPa, or 18 psi.) If a replacement cap is needed, use an AC cap, or
an equivalent cap, designed fof coolant recovery systems and specffied for
your model.
4. Tighten all radiator hose clamps ang heater hose clamps and inspect all
hoses. Replace the hOSes if they are swollen, "checked" or otherwise worn.
NOTICE: Take care when tightening the hose clamps at the radiator. Overtightening could bend or collapse the radiator fittings.
5. Clean the front of the radiator core and air conditioning condenser to
remove dirt and other objects. Also clean the auxiliary engine oil andlor
transmission fluid cooler if the vehicle has them.
Coolant Replacernent
At the intervals specffied in Section A of the Maintenance Schedule folder, flush
9r1d refill the cooling system as follows:
1. Remove the radiator cap when the engine is cool:
•
Turn the cap slowly to the left until it reaches a "stop." Do not press
down while turning the
cap.
• Wait until any remaining pressure (indicated by a hissing sound) is
relieved, then press down on the cap and continue turning it to the left.
CAUTION: To help avoid the dangarm being burned. donotrem_ove the radiator cap While the engine' and radiator are. still. hot. Scaldingftukland steam ean be blown out under ~re It the cap is taken off too SOOf1.
2. When the cap is removed, run the engine until the upper rad.iator hose is
hot.
(ThiS shows that th~ thermostat is open and the coolant is flowing
through the system.)
3. Stop the engine. Open Ihe,actialor drain valVE! to drain the coolant. Drainage may be speeded by removing the drain plugs in the block, ff so
equipped.
5-7

Downloaded from www.Manualslib.com manuals search engine Rear Axle, Standard
See Section A of the Maintenance Schedule folder to find out how often the
lubricant level should be checked. If you pull a trailer, the lubricant must be changed as recommended in the Maintenance.Schedule folder.
Add lubricant, if needed, to fill to the level of the filler plug hole on the
passenger's side of the
differential case. Use SAE BOW GL-S or SAE BOW·90
GL-S gear lubricant. (For those vehicles driven in Canada, use SAE BOW GL-S gear lubricant.) You can also use special gear lubricant Part No. GM 10S2271
or 10S2272. You can buy these products from your dealer.
Rear Axle--!-imited-Slip Differential
See Section A of the Maintenance Schedule folder to find out when the lubricant should be drained and refilled.
Refill to the level of the filler plug hole with special gear lubricant part No. GM
1052271 or 10S2272. You can buy these products from your authorized dealer.
Power Steering System
Check the fluid level in the power steering pump as recommended in the
Maintenance Schedule folder.
Add GM Power Steering Fluid (Part Number GM 1 OSOOI7) as needed:
"HOT"
"COLO"
"ADD"'"
• If the fluid is warmed up (about 66'C or IS0'F --hot to the touch), the
fluid level should be between the "Hot" and "Cold" marks on the filler cap
indicator.
• If cool (about 21 'C or 70'F), the fluid level should be between the "Add" and "Cold" marks.
This
fluid does not need periodic changing.
Air Cleaner Element
When replacement afair cleaner filter.;element is necessary. an AC air filter element is recommended.
See your Maintenance Schedule for change intervals. Operation of vehicle in
dusty areas will',necessitate more.frequentreplacernent.' Your dealer. can be of
assistance in determining the properreplacement.frequency for the conditions under which you operate your vehicle.
S-9

Downloaded from www.Manualslib.com manuals search engine CAUTION': It" the alr 'l;lMner i, ren;oveci during repair or maintenance, bel"'re to put H bl,ck on'eQr~ctly. It the air cleilner Is 'not correctly Inltalled. there could bea fire in the engine compertment (It there ~Id h..,.,en to be a backfire) , or other engitie mallunc1lon .
Front Suspension and Steering Linkage
Lubric;lte fi tngsatlhEj ' intery;>1 showninthe Maintenance Schedule with water
resistant
EP Chassis lUb(icantwhich meets GM SpecifICation 6031M.
NOTICE: ,Ball ' joints, should "not be . lubrieak.d unlesS, their temperature il -12"C (10"f},or higher,During ,coldweather, theyahould" .. ~"al,)c)~ to,warm up al nece ... ry ,before being lubricated or damttge to the baH jOint-Could occur. . , ' '.' "
.. ,. fIRnl 'N. c~~~arings
Clean and repack front wheel bearings with a high melting point wheel bearing
lubricant . at the interval shown in the Maintenance Schecule. Use wheel
' bearing lubricant GM Part No. 10 5~ 344 or equivalent.
NonCE: ," Long fiber " or "vbeou.'-' type"iubricenf ~kI nol be used, Do not mix wheel ~irinQ"lUbricant., Be sure to thoroughly c5aan bearings and hubl of all old lubricant before repacking.
Tapered roller,bearings uaed'h'Hhis 'veh icle have' .. sUghtly looSe teel when properly adjusted, They must never ~ over tightened (preJoaded) or sev .... bearing damage may resuit. Con.utt your,Authorized Deektr or Servi<:e.r.enual tor peper detailed adjustment procedures and specifications. . '~". :...,"" .... ~"";~f>"'~"'-"'''''',','',' ,::, Hood tlltchesand.Hood Hinge
At the interva l shown in the Maintenan ce Schedule lubricate hood latch
assembly
and hood hinge assembly as follows :
1. Wipe off any accumul"ti~!).ofqirt Qfoontaminationon latch Pi1!'ts.
2. Apply Lubriplate . or equivalent to latch pilot bolts and latch locking
plate .
3. Apply light engine oil to all pivot paints in release mechanism, as well
as primary and Secbndary latch mechanisms.
4. Lubricate hood hinges .
5~ Make hood hinge and latch mechanism functional check to assure the assembly is working COfTectiy.
Freedom Battery
Your new vehicle has a Delco FREEOOM battery. It neecs . no periodic
maintenance .
Its top is permanently sealec (except for two small vent holes) and has no filler capS. You will never have to add water.
The hydrometer (test indicator) in the top of the battery provides information for
testing purposes only.
For full power needs at replacement time, a Delco battery wijh the same catalog number as shown on the original battery's labe l is recommended ..
CAUTIQN: ",' FOllOW the precautions listed in the' Jump Starting ' 'Caution (see ' Ihe "In Case of EmergenCy " settlon of this manual) when workmg On or 08. a bMtery. Personal Injury {particularly to eyea} or 'property damage may result from battery e~ battery acid, or electrical (short circuit) burns.
5-10

Downloaded from www.Manualslib.com manuals search engine STANDARD EXTRA B C o
TIRE-LOAD AND INFLATION PRESSURES
TIRE lOAO RAlliGE
-{METRIC SIZE TIRE) " -{METRIC SIZE T!RE) -(ALPKA-NUMIiRIC SJZETIRE) -(ALPHA-NUMERIC SIZE TIRE) -(ALPHA-NUMERIC SIZE TIRE)
MAXIMUM COLO INHATtoN "'E$SURE
2
40 kPI 280 kPa 220 kPa 2M! kPt 27S kP.
t 35 psi J (41 psi) (32 psi) (36 psi) (40 p.JiI
TIRE LOAD RANGE IS MOLDED Off TIRE. !SEE I UUSTRATIOff ON PAGE ,So11 fOR lOCATION ON THE TIRE S IDEWALl! .
4. Always use a tire pressure gage when checking inflation pressures (we
suggest
you purchase a quality pocket-type gage). Simply looking at the
tires to check inftation pressures is not enough , especially with radia l tires .
Underinflated radial tires may
look like correctly inflated radial tires. H the.
inflation pressure on a tire is often low , have your d9aler correct the cause.
) , I" , "
,
~ , ~ , , , , ) ,
,
,
'"
,
~
'"
,
0:: ~ , , ~ :0 , ,
PROPERLY INFlATED IMPROPERLV INRATED
l ___ ~_~)
y IlADIAL TIRE
5. Be sure to put the tire inflation valve caps back on, if so equipped. This
will help keep dirt · and moisture from getting into the valve core which
could cause a leak.
6. If an air loss occurs while driving, do not drive on the flat tire more than is
needed to stop safely. Driving even a short distance
ona flat tire can
damage a tire and wheel beyond repair.
Inspection and Rotation
Front and rear tires perlorm different jobs and can wear differently depending
on the types of roads driven , your driving habits, etc .
For longer tire
life, you should inspect and rotate your tires as recommended in
Section A of the Maintenance Schedule folder. Many car and tire dealers will perform a free tire inspection to look for uneven or abnormal tire wear (usually
caused
by wrong inflation pressures, lack of regular rotation, improper wheel
alignment, out
of balance tires, or poor driving habits).
After rotation , adjust the front
and. rear tire pressures (see the Tire Placard)
and be sure to check wheel nut tightness . (Wheel nuts should also be
tightened at certain intervals; see the Wheel Nut Torque Caution in "In Case of
Emergency" section,
page 3·7, for further information.)
5-13