Downloaded from www.Manualslib.com manuals search engine Power Windows (OptIonal)
Power windows have an ignition interlock SO the windows cannot be operated
unless the Ignition switch is in the "RUN" poSition A master control for all
windows is provided at the driver's position. Individual switches are provided
under each
window for passenger use.
INSIDE REARVIEW MIRROR
The mirror can be adjusted up, down or sideways to obtain the best v.iew to
the front and rear. Move the mirror lever to the night position to reduce glare
from the headlights of vehicles behind you.
OUTSIDE REARVIEW MIRROR
Adjust the outside mirror so you can just see the side of your vehicle in the
portion 01 the mirror clo§!tsu.o .. the vehicle. This helps youdetermirie your
relation to objects seen in the mirr or:" .
CONVEX MIRROR
YoUr vehicle may have an optional convex outside rearview mirror. (A convex
mirror has a
cu
vehicle in the portion of the mirror closest to the vehicle. Thi s type
of mirror is designed to give a much wider view to the rear. especially of the
lane next to your vehicle . This may be most helpful when you want to change
lanes , or in some cases when you want to back up. Ho_ver, cars and other objects seen in a convex mirror will· LOOK smaller and appear farther
away than when seen
in a flat mirror. Therefore, use care when judging the
size or distance of a car or object seen in this convex mirror. Use your inside
mirror (or
glance rearward) to determine the size and distance of objects seen
in the convex mirror.
SEAT CONTROLS
ADJUSTMENT OF SEAT POSITION
Manually Operated Front Seats
The front seats may be adjusted forward or rearward by moving the control
lever at the front Of the seat to the left and exerting slight body pressure in the
direction desired.
The seat is locked in position when the lever is released .
1-3
Downloaded from www.Manualslib.com manuals search engine • To lengthen the center seai lap bett,place the latch plate at a right angle to
the belt webbing and pull on the latcn plate. The belt should then slide
easily .
...,
ADDITIONAL REAR SEAT SHOULDER BELTS Offered as an
Accessory by ,Your Dealer
• When properly worn with a lap bett, a shoulder belt can give riders added protection . It can prevent or reduce impact with the iilsidesof the vehicle
by restraining the upper 'body in a collision. This is especially true in a
frO!ltal'~';".,'k '~ " ','" ' , • , ' "
• To use t~e detach8lJ1lf~Ider'belt .. place the knob on the shoulder belt end in the "keyhole " On the lap' belt latch plate (before fastening the lap
belt.)
Tilt the knob as needed to pass it through the Slot. Pull the, knob
firmly upward to seat n at theoarrow· EI/ld of the keyhole , thet;l·fasten the lap ,belt. Do this in reverse when taking'off the shoulder bett and putting it .
away.
• The 'detachable shouidElI'bilfts,can way ,as center seat lap belts.
•
The de1achable , shoulder belt should have enough slack to put a fist's
width between your chest ,and the, bett . This can be checked by putting a clenched fist between the bett and your chest. (Place the thumb side of
your fist against your.&hest with the back of your hand facingu·p.)
, 1-9
Downloaded from www.Manualslib.com manuals search engine The GM Child Love Seat is not recommended for use in the center front
seating position of this vehicle because it may Interfere with quick access
to all front seat belt buckles in an emergency.
To make it easier
to install a GM Child Love Seat in the rear seat of this
vehicle, at least one pre- drilled hole for the top strap anchor bracket has been
provided in the filler
panel between the rear seat and the rear window . It will be
necessary to pierce the trim panel (covering the metal panel Itself) with a hole
that corresponds
to the pre-drilled hole. T 6 find the hole, enter the trunk and
examine the underside of the filler panel. See the booklet that comes with the
Child
Seat for details on locating and mounting the top strap anchor bracket.
When the child
Seat is placed in the car, use the seating position most directly
in front of the anchor bracket and secure the seat using the top strap and the
car lap belt. In using any infant or child restraint system, be sure to read and
follow all instructionsoninstatlatlon and use that come with .the restraint
system.
When not in
use, leave the Love Seat, or other infant or child restraint system,
in place
and restrained by the car's seat belt. If that is not possible, store the
restraint in the trunk to help keep it from being thrown about and injurying
people in the car during a suddlen maneuver or an accident.
Children
small enough for the GM Infant or Child love . Seats described
above, or other such infant and child restraints, should be restrained by
such means IF AT ALL POSSIBLE. Although the following measures may
lessen the chance
andlor severity of injury fn an accident or suddlen maneuver
for such
small children , they simply cannot do SO to the dlegree that specially designed child restraints can. Take care as follows ~ a child is ricing in the
vehicle without a General Motors
(or other) infant or child restraint system:
1 . Infants who cannot sit
up· by . themselves should be restrained by placing
them in
a· bassinet, preferably cQvered and padded. Place it crossways in
the vehicle (widthwise) on the rear seat.
The bassinet should be securely
restrained with the vehicle 's regular seat belts. Another method is to place
the bassinet
so that iI rests against the back of the driver 's seat. again
crossways
in the vehicle .
1-11
Downloaded from www.Manualslib.com manuals search engine The trunk lid should be closed while driving to help prevent drawing exhaust gas into the vehicle. If the trunk must remain open for some reason while
moving . or ff electricai wiring or other cable conneclionS to a trailer must pass through the sealbelweeri the trunk lid and the body, follow these precautionS :
• Close all windows.
• Adjust the heating or cooling system to force outside air into the vehicle as
described above. but set the fan to high speed .
• On vehicles with outside ' air vents in or under the instrument panel ; open
the vents
fully.
NEW VEHICLE "BREAK-IN" PERIOD
You can drive your new vehicle from its very first mile/kilometer without
following a formal "break-in" schedule. However. there are things you can do during the first few hundred miles/kilometers of driving . that will add to the
future performance and economy of your
vehicle. We recommend you limit
your speed during the first 500 miles (800 kilometers) to a maximum of 55 mph (90 km /h) ; but do not drive for long periods at anyone constant speed. either
fast or
slow. During this time. avoid full throttle starts and. if possible. avoid
hard stops especially during the first 200 miles (320 kilometers) of driving .
Always drive at moderate speed until the engine has COfl'4lletely warmed up.
If you plan to use your new vehicle for trailer towing . see additional information
under " Trailer Towing" in Section 1 of this manual.
GUARD AGAINST THEFT
y~~; '~ew Monte carlo has many features to help prevent theft of the vehicle
itself.
its equipment. and its contents. But these anti-theft features depend
upon you to work.
THE
TIME TO BE MOST ON GUARD ISWHEN LEAVING THE VEHICLE ...
• PARK IN A LIGHTED SPOT WHEN YOU CAN AND FULLY ClOSE BOTH WINDOWS AND ANY ROOF PANaS
• LOCK THE STEERING COLUMN AND TAKE THE KEYS:
•
Turn the key to "Lock " and remove the key. This locks the ignition
and both steering and shift controls.
• If you must leave a kilY with the vehicle . leave the square-head key only. Take the oval· head key with you. This will help prevent unwanted
entry into your
vehicle at a later date . or into your glove box (if locked) or trun k
• LOCK ALL DOORS .
•
KEEP ITEMS OUT OF SIGHT AND LOCKED UP WHEN POSSIBLE.
• Never leave things of va lue in plain sight on seats or floor.
• The glove box otTers a place to hide small item s and if locked, protects even better.
• Lock larger item s in the trunk.
Downloaded from www.Manualslib.com manuals search engine FUEL REQUIREMENTS
Your engine is designed to use only unleaded gasoline . Unleaded gasoline must be uSed for the emission control system to operate properly . Its use will
also reduce spark
plug fouling, exhaust .system corrosion and engine oil deterioration.
Using
leaded gaso~ne can damage the emission control system and could
result
in loss of warranty coverage. The effectiveness of the catalyst in the
catalytic converter decreases after use of as little as one tank of leaded
gasoline.
Also, your vehicle may have the "Computer Command Control" system, which includes an oxygen sensor. Leaded gasoline will damage the
sensor,
and attect emissioncont(ols. (For more information, see "Computer
Command Control
System" in "Service and Maintenance,"Section 5 of this manual. Federal regulations require that pumps delivering unleaded-gasoline
be labeled with the word UNLEADED. Only these pumps have nozzles whichftl the filler neck of your vehicle's gasoline tank.
In the United States, Federal law also requires that gasoline octane ratings be
posted on the pumps. The octane rating shown is an average of Research
octane (R) and Moto< octane (M). In most parts of the United States , you
should use unleaded gasoline with an octane rating of at least 87. However,
you may use unleaded gasoline with an Q!;tane rating as low as 85 in these
. high -altitude areas: Coloraclo , Montana, New Mexico , Utah , Wyoming,
northeastern Nevada, southern Idaho, western South Dakota, and that part of
Texas which is directly south of New Mexico .
Using unleaded gasoline with
an octane rating lower than stated above can
cause persistent, heavy
"spark knock." (" Spark knock" is a metallic rapping
noise.) " severe, this can
lead to engine darnage. " you detect heavy spark knock even ",hery using gasoline of the stated octane rating, 0<. if you hear steady spark knoo~ 'wfiil.)' Holding a' steady speed on level roads, have your
dealer correct the
problem . Failure to take steps to stop such knocking is
misuse
of the vehicle, for which Chevrolet is not responsible . However, now and then you may notice light spark knock for a short time while accelerating
or driving
up hills : This is no cause fo< concern, because you get the greatest
fuel economy
benem from the gasoline's octane rating when there is
occasional light spark knock. Using .gasoline with a higher .octane rating than
that which
allows occasional spark knock is an unnecessary expense.
Gasohol
Gasohol, a mixture of unleaded gasoline and ethanol (grain alcohol), is
available in some areas , You may use gasohol in yourvehicle ,provided it is no
more than 10% ethanoL Be sure the gasohol has octane ratings no lower than
those stated above for unleaded
gasoline . Some vehicles using gasohol could run leaner . Most drivers will not notice a difference, but some may. In such
cases your authorized dealer can make c.ertain adjustments, provided they are
not in violation of the Federal
Clean Air Act. " you. are still not satisfied with gaSOhol performance , you may prefer to uSe unleaded gasoline. •
NOTICE: ,Take care to not spiH gasohol on painted surfaces. Gasohol can cause paint damage, which may not be covered und~r the new vehicle warranty.
2·3
Downloaded from www.Manualslib.com manuals search engine OPERATION IN FOREIGN COUNTRIES
All models which have the Computer Command Control system, (see "Service
and Maintenance," Section 5), are designed
to use unleaded gasoline as
specified under
"Fuel Requirements" in this section of the manual. Therefore,
these cars are not intended for use in areas where unleaded gasoline is
not readily available,
There also is a chance the gasolines available in some countries will not meet the needs of your gasoline engine even if it is not equipped with the Computer
Command Control system; Low~octane-ratedgasolines may cause engine pre
ignition and serious engine damage, for which Chevrolet is not responsible.
In either case (with or without the Computer Command Control system), the
use of leaded gasoline will cause the emission control system to lose its
effectiveness.
It could also affect coverage· under the emission warranty. In
case of emergency, leaded gasoline may be used in your vehicle if unleaded gasoline is not available, but it should not be used exclusively. If you must use
leaded gasoline exclusively
in a vehicle designed for unleaded gasoline,
different maintenance intervals will be required. For additional information and
a copy of the maintenance schedule write to: Chevrolet Motor Division, Consumer Relations Department, Warren, Michigan 48090, (in Canada, write
to General Motors of Canada Limited, Customer Service Department, Oshawa,
Ontario
L 1J 5Z6).
When writing, please
include:
•
the Vehicle Identification Number and
• the countries in which you plan to travel.
Tires
If you plan to use your vehicle in countries where speeds over 75 mph (120
km/h) are allowed, see lIem3 on page 5-12.
IMPORTANT FACTS YOU SHOULD KNOW ABOUT FUEL
ECONOMY AND HOW
TO IMPROVE IT
How you drive, where you drive and when you drive all affect how many miles/
kilometers you can get from a galion/liter of fuel. The careful attention you give
your vehicle as far as maintenance and repairs are concerned
will also help
fuel economy.
Fuel Selection
Use only unleaded gasoline meeting the octane ratings given under "Fuel Requirements" in "Starting and Operating," Section 2 of this manual.
Unleaded gasoline must be used. for the. emission control ,system to operate
properly. Leaded gasoline will damage the Computer Command Control system
oxygen sensor and affect emission control. Using leaded gasoline can also
damage other parts of the emission control system and
CQuld result in 19s8 of
emission warranty coverage.
"Jackrabbit" Starts
You can save fuel (and prolong engine and tire life) by avoiding fast starts
away from lights and stop signs.
2-4
Downloaded from www.Manualslib.com manuals search engine • Firmly apply the parking brake. Do not use ·the transmission as asubsmute for the parking I)rake.
•
Move the automatic transmission shift lever to "P"(Park).
•
Turn the key to "Lock ."
•
Remove the key (the · buzzer is designed to remind you).
• Lock all doors .
TURN SIGNAL AND HEADLIGHT BEAM LEVER
The turn signal lever on the left side of the steering column also controls
headlight low-beam and high-beam and the optional Cruise Control. (For Cruise Control operation, see page 2-12.)
• Turn Signal -Move the lever up to the second stop to signal a right turn.
Move it down to the second stop to signal a left turn. When the turn is
completed, the signal will cancel and the lever will return to horizontal.
• Lane Change Signal -In some turns, such as changing lanes, the steering wheel is not turned far enough to cancel the turn signal . ·For convenience,
you can flash the turn signal by moving the lever part way (to the first stop)
and holding it there. The lever will return to horizontal when you release it.
TURN SIGNAL MOVE UPWARD -R.H. TURN MOVE DOWNWARD -l.H. TURN
I LANE CHANGE I MOVE UPWARD TO
HEADLIGHT BEAM CHANGER (HEADUGHTS ON)
PUtl LEVER TQWARDYOU
l$T STOP-CHANGE FROM LEFT TO 'RIGHT lANE
MOVE DOWNWARD TO 1ST STOP-CHANGE FROM RIGHT TO LEFT LANE
A green light on the instrument panel is designed to flash to tell, you that the
lront and rear turn signal lights are working . If the light stays on, but does not
flash, check for burned-out turn signal bulbs.
If the green light does not come on when you move the lever, check the fuse and indicator bulb. However, if
you ordered a traiter towing option in which extra wiring was added to attach
the
trailer lighting, a different type'of flasher was installed. In tliis case, the
green light will continue to flash even if a turn signal bulb bUrns out. Therefore ,
you must
regularly look at the front and rear turn signal lights to be sure they
are working.
• Headlight Beam Changer -With the headlights on, pull the lever toward
you until you hear a click, then release it. The lights will change from Iow
beamto high-beam or from high-beam to low-beam . When the hig~-beams
are on, a blue light will appear on the instrument panel.
CORNERING UGHTS
The front fender cornering lights operate in conjunction with the turn signals.
When the turn signal is operating in either direction, and the headlights or
parking
lights are on, the corresponding cornering light emits a steady
sideward beam to provide additional illumination .
2-7
Downloaded from www.Manualslib.com manuals search engine • Opet'ating the transmission at 'Of 'near,"st8Jlcondition" lor more than 1 0
secorlds at a time, ("Stall condition" is wfj~~ t~e engine is running at ,high
speed while the transmission is in a driving range arid the drive wtieels
aren't moving, such as when stuck in deep sand or whe(l the vehicle is
against a fixed barrier.) ,
•
Holding vehicle on an upgrede with the acCelerator pedal. (\Jse the regular
brakes to hold vehicle on an uphill grade.)
Column Shift Lever
The heavy line in the illustration indicatesihe movementol the shift lever as it
is lifted to shift into Reverse Of Low arid into or out 01 Park position . ,
~ ---. .,.-'.' . ...,..~;~.. .. .. -- -' -, .-,--. Floor ConsOliFSI\1ff~"~,,(C'·,':"
The floor shift lever may be moved freely between Neutral and Drive arid between 1 and 2. Press lightly oil the shift lever button (located on the side 01
'. ttie-shift lever) as you shift into ReviJ(se ' or from Drive into ~, Depress the
button fully when shifting into or out 01 the Park position . ExerCise ,care when
depressing button to
prev,!"'t unintenti
the
load ,arid speed criteria that satisfy requirements lor an autDmatic upshift, ~ -. - -.
POWER STEERING
II the power steering assist' system goes'''' ut beeaus .e the engine has stalled or due to a lailure , the vehicle can ,still be steered . However , much greater eitort
is needed , especially in sharp turns or at
low speeds . '
TILT STEERING WHEEL
The optional tilt steering wheel The tilt steering wheel (where equipped) can be
tilted up above
normal position to provide edditional room lor entrance' and exit
as
well'ss . selected driving ,positions bei<>w ilormalheight. The ti~ control lever is located on the left side 01 the steering.'column just behind . the turn signal
lever . To operate pull
the lever tow'¥ds you and move the steering wheel to
your desired
pos!~on then releaSe!?e lever. This permits individual seleclion 01 the most comfortable positionS lor. all driving conditions , On longer trips the
steering wheel position may be changed to help minimize tension
and latigue.
2-11
. ------ ,------