1980 SKODA 105S engine oil

Turn
the flonge
on the centering
orbor so thot
the longer, cylindricol port
foces the clutch,
push it ogoinst the friction plote
hub, ond olign
the ends of the levers to touch the flonge.
A deviotion from the ploneness
of 0.1 mm
is
permissible. Use feeler gouges for checking
this deviotion.
lf it is not possible
to odiust the out-trovel of
the clutch releose levers to o volue given
by the
length of the flonge cylindricol port
due to
excessive weor
of the friction plote, odiust to
the next higher volue.
Clinch nuts on the
odiusting nuts bocked off up to the end of the
threod ore o worning of o weor limit which pre-
cludes ony further odiustment
of the clutch.
4. After hoving reossembled
the engine with
o new or odiusted clutch,
check ond, if necess-
ory, odiust the cleoronce between the releose
levers ond the throw-out beoring -
see Chop-
ter 15.4.
3.3 CLUTCH DISMANTLING
Owing to its simplicity,
it is not necessory
to
describe in detoil the dismontling
of the clutch,
but some speciol feotures
deserve ottention.
1. lf the friction plote
ond clutch cover ore
intended to be re-used, mork their relotive
positions using centre punch
morks to preserve
the originol bolonce of the ossembly.
2. To dismontle
the clutch, it is
necessory to
compress the clutch cover to relieve the stress
of the releose lever bolts. For this purpose
use
the MP 2-101
ossembly plote
shown in Fig.3.4/1.
After screwing off the releose lever nuts ond
compressing the clutch cover,
the clutch is
reody for dismontling.
3.4 CLUTCH REASSEMBLY
1. Locote
the clutch pressure
plote
on the
MP 2-101
ossembly plote
ond fit springs
on the
cylindricol bosses. Before fitting
the springs, it
is odvisoble to check them for
complionce with
the volues specified
in the following Toble.
Toble of Clutch Springs
Lood
Length of spring in mm
lin -rrr"ltp1
Mounted length
31.55'10+36
(s2t3.6)
Length of compressed spring 29.5
I 580 (59) 2.
Instoll retoining plotes
on the clutch
springs ond fit the clutch cover with releose
lever springs in position.
Assemble the clutch
cover with the pressure plote,
observing the
morks indicoting their relotive positions.
When
ossembling new pot'ts,
their positions
ore of no
consequence.
3. Slip o 4.5 mm high pod
over the ossembly
plote bolts (the
plote
con be used
for Skodo
1000 MB ond Skodo 100 cors os well,
ond by
using pods
of different heights, the plote
con be
odopted for different
types of clutches), fit the
yoke of the
iig on
the plote
bolt ond compress
it by screwing down the nut till the bottom port
rests on the pod.
When compressing the clutch
cover toke core thot the projections
of the
pressure plote
ore correctly centered in
the
cover slots to prevent
o distortion of the clutch
cover.
4. Slip the bottom ends of the releose levers
under the springs instolled in the cover ond fit
them with their longitudinol
slots on the sup-
ports. Slip odiusting woshers on the bolts of the
pressure plote ond screw down the nuts with
their cylindricol port
focing the woshers. Then
odjust the height of the releose levers with
these nuts so thot their ends touch the shoulder
of the yoke
bottom port.
The difference of the
lever height should not exceed 0.'l mm. This
odiustment olso sets the recommended
distonce
of the levers from the pressure
plote
beoring
surfoce.
Use clinch nuts for locking the odiusting nuts
in position,
put
supporting clips under the re-
leose f ever ends os shown in Fig.3.111 ond3.212,
ond slocken the nuts of the ossembly plote.
The
clips ore useful when fitting the clutch to the
f lywheel since it is not necessory to overcome
the tension of the clutch springs.
To Check Adiustment ond Bolance
The described od justment
of the releose levers
in the
iig is
the most occurote, the ossembly Fig.3
Dim
plote be
simulotin
For on<
porogropl
The cl
with the
friction ;
ports of '
clutch on
To bol
centering
pressure
the chips
lf thesr
boloncing ing holes
in o circk
4mmofr
between
fostening
3.5 FR|C
lf the f
it is odvi
8.5 mm th
When r
the frictio
ond only r
complicot
After hr
the plote
if necessc
recheckinl
quired.
70 Fig.3.4l1
-
IAP 2lol
Assembly Plote with Clutch

r
t
i
5. Prc
scri bed
rods onc
4th spee
fork rod,
irr the b
6. lnsl
guide bu
cover inr heods. S
tob wos
edges of
F it thr
stri ki ng
weoker s
ing forks 7. Tigl
the forks fork rod
the strik
function
Reverse-:
Fig
-1 - Rever
2-1st-o
3-3rd- o
4 -
Rever
8. Inst
press-f ittr
verse-spe
inside th
through t
Turn tl'
end foces
lock it in
hole. Tigl
Pinion Ar
9. Instc
ing ond,
r
_-_-- -
. i\:r,,,
\. 43
Fig. A.1l'l -
Power Pock
1 -
engine with mounting, 2 -
georbox/f inol
drive with
mounting, 3 -
reor oxle (holf-oxles),
4 -
rodius orms
retighten it using the recommended torque
(Chopter 1.8) ond screw down the clinch nut.
lf necessory, top up engine oil, f ill the cooling
system witlr on qntifreeze,
bleed the broke sys-
tem, ond
odiust the hond broke.
For the fosten-
ing of broke hoses (routing)
see Chopter 9.7.
4.2 ASSEMBLING
GEARBOX
Generolly, the reossembly
p'rocedure
depends
on the extent, to wlrich the unit hos been token
oport. For betterunderstonding,
we sholl des-
cribe the procedure
ond peculieorities
of reos-
sembly of o completely
disossembled unit.
Gear Chonge Mechonism
. 1.
Clomp the right-hond holf of the housing
(when viewed from the flonge securing
it to
the engine) in the MP 9-101 stond
com-
plemented with the MP 3-101 georbox
rock, ond
check the housing for completeness.
2. Instoll
circlips on the striking fork rods
of
the reverse
ond 1st ond 2nd speed. The ring
with the lower
nose is to be fitted
on the 1st--
ond 2nd-speed rods.
3. lnsert the reverse speed
striking fork rod
into the housing
so thot the inserted
end pro-
trudes slightly from its guide,
slip on it the
striking fork with the longer
side of its heod
first,- ond push
the striking fork rod through
the fork
ond the end of the guide
os for os=it
will go. 4. Fit tlre
MP 3-109 jig
into the free holes for
striking fork rods (both pins
of the
iig), ond
proceeding through the hole in its side ond
using o stick or o length of wire, push
the lock
pin into the housing
os for os it will go.
Proceed
in the some monner for
inserting the next pin
(use one pirr
of the
iig). Shift
it
iust so thot
the centre lrole remoins free for inserting
the
striking rod.
Puslr the lock pin
into the end
guide of the strikirrg
fork rods olso os for os it
will go. The
iig is not required
for
the instol-
lqtion of this pin.
Fig.4.2l1- Clomping Georbox Housing in Stond
Using MP 3-101 Rock
Fig.4.212 -
Locking Striking Fork Rods in
Position bv Meons of Lock
Pins ond Bolls
78 Fig.4.2l3
-
Instolling Lock Pins Using
MP 3-109 Jig

1 1.8-11.10
11.8 HEATER
CONNECTING LINE
The line is o
combinotion of steel pipes
ond
rubber hoses. All connections must be tightened
with clips of
the strip
type (see
Fig. 11.411) or
the wire type (bleed
hose). Toke
core not to
overtighten the clips of the lotter type os there
is o risk of domoging the rubber.
The hose from the pipe
of the thermostot
body on the engine is routed to the heoter
through the f loor tunnel, the return bronch
possing ogoin through the tunnel to the pipe
of
the pump.
Arronge the hoses olong the sides
of
the floor tunnel so
thot they do not touch other
ports in the tunnel.
For detoiled informotion obout the routing of
the hoses refer to
Chopter 12.7.
11.9 otl COOLER
The oil cooler is stondord
equipment of
Skodo
120 LS models. lts construction resembles thot
of the rodiotor. lt is
instolled in the
engine
comportment (boy)
ond ottoched to the right-
-hond engine guord.
Speciol pressure
hoses
connect it with the engine. lts connecting
diogrom is shown in
Fig. 11.911.
As regords oil coolers for subtropicol ond
tropicol regions, refer to
Chopters 16.1
ond '16.2.
Fi9.11.9/1 -
Oil Cooler-to-engine Connecting
Diogrom
1 -
Outlet from engine-right-hond cooler socket,
2 -
Oil cooler, 3 -
Inlet into engine -
left-hond
cooler socket Removol ond
Refitting
Disconnect the hoses fronr the engine ond,
occording to circumstonces ond the purpose
of
the removol, detoch the oil cooler from
the
engine guord
or remove the engine guord
together with the cooler ond brocket. Empty the
oil contoined in the hoses ond the oil cooler
into o suitoble vessel. When refitting the oil
cooler into the cor,
proceed in occordonce with the circumstonces
of the removol. Secure the bolts conecting the
oil cooler with the engine guord
ond the brocket
(the brocket being locoted between the cooler
ond the guord)
with spring
woshers. Bolt down
the guord
over ploin
woshers ond use o spring
wosher for the bolted connection of the brocket
with the bodywork.
Use seoling
woshers when connecting hoses
to the engine ond the oil cooler, ond put
o seoling wosher olso under the bolt. Close the
bolt of the engine port
ot the flonge with the
pressure switch. Fosten the hoses so thot they
ore not stressed in their bends. The
hose from
the timing geor
cover should be routed horizon-
tolly ond the hose ot
the engine inlet so thot
it includes o downword ongle of obout 15 de-
grees with the horizontol plone. Top up
oil in
the engine.
11.10 COOLING SYSTEM DEFECTS,
TESTING, REPAIRS, AND
CLEANING
Defects ond Testing o) lf there is o marked loss of coolont, check
oll connections for leokoge. The
loss of coolont
con olso be coused by o leokoge of the rodiotor
(or heoter). lf the leokoge point
is not visible,
pressure-test the system without removing it
from the cor. Admit seoled-off oir ot o pressure
of 0.12 MPo
(1.2 kglcmz) into the filler neck ond look for
ploces where the coolont is seeping or dripping
out. Inspect not only the rodiotor but olso the
lreoter. An excessive loss of the coolont con be olso
coused by engine overheoting. In thot cose,
look for the couse of engine overheoting.
b) Points to check if the engine
is overheoting
- coolont level
- operotion of thermostots ond rodiotor fon
- condition of rodiotor (whether
clogged out-
side with dirt, or whether cooted inside with
scole)
c) Points to check if the engine does not worm
up properly:
- operotion of thermostots
DX
tfSJ
156

r 2.1-t 2.3
I
I I
I
Dissssembly
ond
Reossembly of Pedols
This is usuolly not necessory. The pedols
con
be disossembled ofter removing the oxiol screw
in the pedol
pin
ond slipping off the return
spring. Do not remove the switches if it is not
obsolutely necessory -
see odiustment. On re-
ossembly, lubricote
the pedol
bush with lubri-
coting greose
of the some brond os used for the
steering linkoge -
see Chopter 7.5, por.3.
Pedol Free Trovel
Adiustment
Adjust the free
trovel of pedols
ossembled
with moster cylinders so thot the pedol piston
rod hos o
cleoronce of 0.5
to 1mm
when beoring
ogoinst the piston
heods of the
moster cylin-
ders. The free trovel of the pedol pod
should be
from 3 to 5 mm. lt
con be odiusted by rototing
the eccentric pin
on the pedol
brocket -
see
Fi9.12.111.
For the odjustment of the broke pedol
with
broke booster ond/or levelling of the broke
pedol with the
clutch pedol,
see Chopter 9.6 -
Ad justment.
Adiustment of Switches The switches con be
moved in
the ellipticol
holes of the brocket ofter loosening the fosten-
ing copscrews with ploin
woshers under their
heods. A pocking piece
should be slipped
under
the switch of the broke pedol
trovel worning
light ond the powl
of the switch pin
should be
held down under the fostening copscrew.
Ad just
the stop-light switch
so thot it
switches on the stop lights ot o pedol
trovel
of 10 to 15 mm meosured on the centre of the
pedol pod.
Adiust the pedol
trovel signolling switch so
thot the pushed-in
side push-button
pin
is
re,ecsed ot o pedol
trovel of 100 to 110 mm
mecsured on
the centre of the pedol
pod.
Press
the push
button into
the switch ofter hoving
completed the
odiustment.
12.2 ACCELERATOR PEDAL AND CABLE
The occelerotor pedol
forms o unit with its
self-lubricoting beoring ond the lever.
lt is
bolted to the f
loor tunnel. A coble possing
through the tunnel is ottoched to the pedol
lever ond the reloy
lever on the engine by
meons of clomps- The coble is protected
by
o Bowden tubing.
Pedol Removing ond Refitting
1. Loosen the clomp holding the coble on the
engine-mounted reloy lever. 2.
Remove the copscrews holding
down the
becrring with the pedol,
depress lightly the
pedol, ond lift it out of the f loor
tunnel together
with the beoring. 3. Disconnect the pedol
from the coble ofter
ioosening the clomp.
Removol ond Refitting of Bowden Tubing
ond Cqble
The Bowden tubing is
fostened to
the brocket
irr the floor tunnel by
meons of circlips. After
their removol, pull
the Bowden tubing inside
the cor. On ref
itting the tubing, lubricote it with
o low-viscosity oil (of
the SAE 20
closs). lt hos
been lubricoted with greose
in the foctory.
Fit
the clonrps so thot their longer ports (from
the
screw to their end) ore on the side of the
I evers.
Accelerotor Coble Adiustment
Adjust the coble so
thot it is not
excessively
tensioned or too slock. Loosen the clomps on
the engine side of the coble, move slightly
the
clomp toword the reloy lever,
ond tighten the
screws of the clomp.
12.3 GEAR SHIFT LEVER
AND LINKAGE
The geor shift mechonism consists of two
units: the geor
lever with its housing ond oc-
cessories, ond the geor
shifter rod
ond the
shifter lirrk with joint
(ot the georbox)
for
domping the vibrotion of the power
pock
tronsnritted to the geor
lever.
Removing Geor Lever
Housing ond Link
1. Lift owoy the mot from the floor tunnel in
the front ond reor comportment. lf seporote,
remove the individuol floor mots ofter hoving
prised out their clips with o screwdriver or
o similor tool. lf o one-piece floor
covering is
used, remove the door sill strips
on one side,
tip the seot, ond bend over the
floor covering.
2. Remove the geor
lever housing copscrews
ond prise
out the lid (next
to the clip) between
the seots. Proceed through the
operture to dls-
connect the bolted connection of the link with
the housing shifter rod.
3. Lift
owoy the housing with the lever
through the operture. Swivel the lever so thot
the shifter rod
does not protrude
over the
housing beoring thus obstructiong the removol.
4. Usuolly it is not necessory to remove the
geor shift link from
the cor. lf
obsolutely necess-
ory, the link con be
disconnected only ofter
162

nolly
emerges into spoce under the floor toword
the georbox.
lt is ottoched to the speedometer
by meons of o union nut ond to the georbox
by
o sleeve ond o screw.
It is lubricoted
with oil from the georbox
which creeps olong it due to copillory elev-
otion" Lubricote it with engine oil of o lower
viscosity dripped into its sheoth only if the
lubricotion by creeping is inodequote. When refitting
it in position, put
it into the
cor from the front, connect its
both ends, ond
then orronge it so thot it does not form ony
shorp bends ond is
not too tout. The speedo-
meter con be disconnected ofter removing
the
instrument ponel,
ond removed by pulling
it in
forword direction.
For the speedometer drive shoft possoge
under the ffoor refer to Chopter 12.7.
166

'i
iiiI 14. Fuse box
Centrol connection of conductors -
do not
seporote them from the bunch!
15. Direction indicotor switches, dip switch,
and horn switch
eight-pole terminol
boord
six-pole terminol boord
16. Porking light switch ond high beom feeder four-pole terminol boord
17. Switch box femole connectors 5.5 with symbols "15",
"30", ond '50"
to be
connected to symbols
"15u, "30', ond '50"
on the switch box
18. Instrument ponel
ten-pole terminol boord
six-pole terminol boord
eorthing coble with lug
'19. Heoter switch
four-pole terminol boord
20. Switch of disobility lights
six-pole terminol boord
21. Door switch, right-hond
green -
femole connector 5.5
22. Dome light,
right-hond
green -
femole connector 5.5
red -
femole connector 5.5
23. Stop switches
forked (yellow) -
femole connectors 5.5 .
red -
femole connector 5.5
white -
femole connector 5.5upper ond lower
switch
upper switch lower switch
24.Fuel gouge block -
femole connector 5.5
yellow -
femole connector 5.5
blue -
femole connector 5.5
to be connected to the respective pins
(blodes) of the some colour of the fuel gouge
25. Storter motor, reversing
lomp switch
conductors with lugs stater motor moin
terminol boord
storter motor
control switch
green -
femole connectors 5.5 heodlomp switch
26. Oil pressure
gouge,
thermometer, corburettor
iet seporotor
green -
femole connector 5.5 yellow
-
femole connector 5.5
green - telethermometer
primory element
femole connector 7.
corburettor
iet seporotor
27. lgnition coil, voltoge regulotor, olternotor,
tochometer
conductor with femole connector ond
bronching lug
femole connector-regulotor terminol 15/54
lug -
ignition coil terminol 15
blue -
femole connector 5.5,
symbol "R"
. regulotor terminol "R"
yellow -
femole connector 5.5,
symbol "M"
regulotor terminol "M"
blue -
connector "R"
. olternotor terminol "R"
yellow -
connector "M".
olternotor terminol "M"
lug terminol "+B"
conductor with
lug ignition coilterminol "1"
(tochometer operotion
)
28. Toil lomp cluster, right.hond
yellow -
femole connector 5.5 toil light
block -
femole connector 5.5 direction indicotors
red -
femole connector 5.5 stop light
green -
femole connector 5.5 reversing lomp
29. Licence plote light
conductors with femole connectors 5.5
30. Toil lomp cluster, left.hond
se point
28.
b) Connection
of free conductors
1. Storoge bottery
bottery coble positive
(*)
terminol -
storter motor
bottery eorthing strip negotive (-)
terminal -
bodywork (eorthing conductor)
2. Engine engine eorthing strip (fostening
lug) -
engine cross beorer (eorthing conductor)
3. Distributor speciol coble from distributor to
ignition
coil; end with interference suppressing
terminol to distributor
coble from distributor to ignition coil
terminol "1"
cylindricol
(pin)
connector
pressure gouge172

junction
with the olternoto,r occording to
Chop-
ier 13.3 ond mointoining
o constont voltoge of
tlre power
supply set within the
entire ronge
of
service speeds.
Tlre voltoge regulotor
is instolled orr the body
cross beorer, to
the right of the engine ond
beside the ignition coil.
To focilitote hondling
of its leods' especiolly
the occess to their
connections, it
is recom-
rrrended to remove the regulotor fostening
screws. For disconnecting procedures,
see
Chopter 13.3 "Alternotor
lnstollotion ond Gen-
erol lnstructions".
DK 1565
Fig.13.411- Internol
Wiring Diogrom of
Alternotol with
Voltoge Regulotor ond
Outer
Connections
Altenrotor: B, R, M -
olternotor outlets
f -
olternotor phose
windings
m -
olternotor field winding
D1,2,3, 4, 5, 6 -
moin diodes
D7, 8,9 -
olternotor ouxiliory diodes
D10 -
olternotor choking diode
Voltoge regulotor:
R, M, 15/54 -
regulotor outlets
reg -
regulotor tension winding
Rk -
boloncing resistor
Ro -
protective resistor
Rr -
odiustoble resistor
Kr -
regulotor contocts
Outer connections: K -
worning lomp (1.5
W)
S -
switch (switch
box)
B -
bottery
Checking Voltoge Regulotor
on Cor
The regulotor operotion con be offected by
loosened connections ond on imperfect eorth- ing.
lf the wsrning lomp does not go
o.ut when
driving, i. e., if it glows
ot increosed engine
speed brightly or dimly,
or if it does not stort
glowing ofter stopping
the engine ond
o new
iurning of the ignition key in
the switch box,
the voitoge regulotor
is probobly
foulty. Another
symptom of o regulotor
foilure is
o poor
chorg-
irrg of tlre bottery or its
overchorging.. lf there
is nothing wrong with the regulotor, check the
reguloted voltoge over the regulotor which
slrould reod 13.2 volts ot the
minimum ond 14.8
volts ot the moximunr. This check
in the
cor
is only tentotive ond only
o check on
the test
bench'con be considered os definite ond
bind'
i ng.
Electricol Adiustment
The voltoge regulotot- should be tested
ond
odjusted only on o test bench
in o connection
slrown in Fig. 13.412.
At o lood of some
2
onrperes, the checked
voltoge should correspond to
volues specified
in the column "Checking".
lf the checked volt-
oge is within the specified ronge, do
not odiust
the regulotor. Othenwise odiust it to the volues
specified in the column "Adiustment".
lf woter
evoporotes obnormolly from the bottery, odiust
the voltoge regulotor to the bosic volues of
"Adiustment" utilizing the lower section of
the
toleronce zone.
Fig.13.al2 -
Wiring Diogrom of
Regulotor Tested
ond Adiusted on
o
G -
olternotor
REG -
voltoge regulotor
A -
ommeter
V -
voltmeter
S -
switch
R -
lood resistor
B -
bottery DK
1566
Voltoge Test Bench
178

I
I
t
b
c ll
e
c
tl
d n
tN'
>
\'
J I
(Il
qt3
Fig. 13.5i3 -
Vocuum Control Course -
opplicoble to both
regulotor models
copscrew fostening the distributor brocket to
the support on the engine (do
not loosen the
brocket clomping bolt).
Refit the distributor on the engine by
re-
versing this procedure. The
coupling on
tlre
shoft is osymmetricol ond it hos to engoge into
the heod of the drive shoft in the engine. To
seot properly
o new distributor
or o distributor,
the brocket of which hos
been loosened, refer
to Chopter 2.3, por.25
to 27.
Distributor Disossembly ond Reossembly
This should be done in speciolizedworkshops,
especiolly with regord
to the checking of the
mechonicol condition or o repoir
of the dis-
tributor. lt is recommended
to use o suitoble
holder for doing the moiority of the required
iobs in
o verticol position.
When reossembling
the distributor, lubricote
the sliding points
oc-
cording to Chopter 15.3
but bewore of over-
lubricotion.
Remove olso the copscrew
on the bottom of
the distributor housing ond drip some low-pour
point oil into the hole to increose the oil reserve
of the shoft
sel-lubricoting beoring -
see Chop-
ter 15.2 "Speciol
Oils".
Disossembly 1. Remove the distributor cop ond the breoker
orm.
2. Remove the coupling from the shoft (note
the relotive position
of the eccentric dogs ond
the breoker
orm).
3. Remove
the circlip from
the pivot
ond litt
owoy the breoker orm.
4. Remove
the subossembly
of the terminol
"1" (current supply to distributor).
5. Screw off the copocitor. 6. Screw
off
the retoining springs.
7. Lilt owoy the vocuum chomber (do
19t
open it, o chonge of the curve is on.improboble
d'efect; do not chonge the screw-in depth
of the
pull-rod).
' 8. Lift owoy the contoct breoker
bose plote
with pocking piece from
the housing.
g. Litt owoy the shoft with the
centrifugol
governor. -
10. lf necessory, disossemble further
the sub'
ossembly of the shoft with the centrif
ugol
governor (odvonce mechonism) ond
com.
l?;h.',0, ReossemblY
1. Reossemble the centrifugol governor
(the
weights must be free
to rotote on the pins).
2. lnstoll the reossembled shoft
with the res'
pective woshers into
the distributor housing.
3. Fit the contoct breoker bose plote
with the
f ixed contoct holder ond pocking
piece into the
housing. 4. Fit the pull-rod on
the pin
ond lock it in
position, screw down the vocuum chiomber with
the copocitor. Check the
ignition odvonce po-
sition for the first cYlinder.
5. Screw down
the retoining springs
with
shims (the
spring with
the dog opposite to
the
terminol "1"i;
the bose plote must
rotote freely
in the distributor housing.
6. Reosemble the terminol "1".
7. Fit the breoker orm
on
the pivot
ond lock
it in position. Adiust the contoct breoker point
gop (lift) ond check the
contoct
Pressure'
"
if. 'Stip
woshers on
the shoft in
the originol
sequence, slip on the coupling ond
lock
it in
position^ 9. Fit the lubricoting felt
into the hole of
the
com ond instoll the breoker orm.
10. Fit the distributor cop
in position.
11. Check the distributor operotion.
Checking A def inite indicotion of the condition of
the
distributor (during on operotionol check
os
well
os ofter o
repoir) con be obtoined by testing
the distributor on
o test stond with
o circulor
spork gop.
After o preliminory
odiustment of
the
contoc-t breoker point gop,
the stond is
used for
check i ng:
1. The contoct point
contoct ongle.
2. The spork ongulor distribution (with o
tol-
eronce of -+45
ongle minutes within
the entire
operotionol ronge).
3. The rongJ ond course of the
centrifugol
ond vocuum control. 4. The
operotion ot
moximum speed (length
of spork on spork goP -
4 mm) for o
brief period
(obout 2 minutes).
180
t
5
2tD zsa !l!
F llti
rc