1973 OPEL MANTA service

3A- 161973 OPEL SERVICE MANUAL
INNER RUBBERSTUD.1 /2”\E
/
PLASTIC COVER
DAMPENING RING
RETAINERRUBBER DAMPENING RING-
-zSELF-LOCKING NUT
UPPER RUBBER
GROMMET RETAINERLOWER
RUBIGROMMET RETAINER
WHEEL HOUSE
SHOCK ABSORBER
SHOCK ABSORBERSA-25Figure
3A-25 Shock Absorber Upper Attachment
7. Remove lower ball joint stud nuts. Slightly lower
jack so that the spring and lower control arm assem-
bly is removed from the front cross member and
steering knuckle.
8. Lower jack, spring compressor, and front spring
and control arm assembly. Remove lower control
arm to spring nuts.
9. Relieve tension on spring compressor and remove
control arm attaching bolts and control arms.
Removal (Opel 1900 - Manta)1. Prior to raising car, install upper control arm
hooks J-23697.
2. Raise car and stipport with stands. Hoist should
be left in the raised position to maintain pressure on
lower control arm.
3. Remove front wheel.
4. Detach both stabilizer supports from cross mem-
ber to body support.5. Remove shock absorber.
6. At lower control arm ball joint, remove castle nut
cotter pin and remove nut.
7. With suitable drift, detach lower control arm ball
joint from steering knuckle.
8. Loosen nut that retains lower control to front
cross member.
9. Slowly lower hoist to release spring tension.
10. Swing lower control arm downwards and remove
front spring.
Installation (GT)
CAUTION:
Fasteners are important attachingparts in
that they could at&t
the performance of vital com-
ponents and systems, and/or could result in major
repair expense. They must be replaced with one of
the same part number or with an equivalent part if
replacement becomes necessary. Do not use a
re-
placement part oflesser quality or substitute design.

3A- 161973 OPEL SERVICE MANUAL
SPECIFICATIONS
Torque Specifications
Use a reliable torque wrench to tighten all parts listed to insure proper
tightness without straining or distorting parts. These specifications are for
clean and lightly-lubricated threads only; dry or dirty threads produce in-
creased friction which prevents accurate maasurement of tightness.
LocationFront Suspension Crossmember to Front Frame
Clamp, Steering Mast to Steering Mast Flange
(GT)
........................................................................................
Clamp, Steering Mast to Steering Mast Flange(1900
-Manta)..................................................................
Clamp,UpperUniversalJoint(GT)..................................Clamp, Lower Universal Joint (GT)
..................................
WheelNuts............................................................................Lower Control Arm Shaft to Lower Control Arm
..........Lower Control Arm Ball Joint to Steering Knuckle
......Upper Control Arm Ball Joint to Steering Knuckle
(GT)........................................................................................Upper Control Arm Ball Joint to Steering Knuckle
(1 900 Manta)
..................................................................Upper Control Arm Ball Joint to Upper Control Arm
ShockAbsorbertoLowerControlArm..........................Steering Arm to Steering Knuckle (1900
- Manta)......
Brake Backing Plate or Brake Disc Shield andSteering Arm to Steering Knuckle
(GTJ
Hex Head Bolt M 10......Hex Head Bolt M 8
......
Brake Backing Plate to Steering Knuckle(1900 Manta)
..................................................................
Brake Caliper to Steering Knuckle.................................
Lower Control Arm to Front Spring Eye (GT)................
Brake Disc to Front Wheel Hub........................................Upper Control Arm to Crossmember (1900
- MantajLower Control Arm to Crossmember (1900
- Manta)
Steering Gear Housing to Front Suspension
Crossmember (GT)
............................................................
Steering Gear Housing to Front SuspensionCrossmember (1900
- Manta)........................................Stabilizer Bar to Lower Control Arm
(Opel 1900
- Manta)........................................................Tie Rod Clamp Bolts
(GTJ....................................................
CastleNut,TieRodtoSteeringArm..............................Upper Control Arm Shaft to Shock Absorber Support
and Upper Control Arm (GT)
..........................................
CrossMember to
BodySupport Attachment................
FrontSuspensionAssemblytoFrame............................Front End Alignment Specifications
Torque
Lb.Ft.36
1522
14
22
6540
5429
ii30
5847
18
58
72
1836
40
43
1830
87
:i33
58
47ModelCaster’
Camber”1900‘3
l/2-6 l/2GT
3+1-:%+*Permissible deviation from left to right wheel
- Max. 1’.
Toe-In”Min.-Max.
l/8-3/ 16
l/32-1/8Outer Wheel
When Inner
Wheel at 20
19
l/418
l/2

STEERING LINKAGE38.19STEERING LINKAGE
CONTENTS
Subject
DESCRIPTION AND OPERATION:
Description
andOperationofTieRods. . . . . . . . . . . . . . . . . . . . . .DIAGNOSIS: (Not Applicable)
MAINTENANCE AND ADJUSTMENTS: (Not
Applicable)
MAJOR REPAIR:
RemovalandInstallationofTieRods. . . . . . . . . . . . . . . . . . . . . . . .Disassembly
andReassemblyofTieRods. . . . . . . . . . . . . . . .SPECIFICATIONS:
Tightening Specifications ..,.............................................Page No.
38-193B-1938-21jB-21
DESCRIPTION AND OPERATION2. Using remover J-21687, pull outer tie rod ball
studs out of steering arms. See Figure
3B-2.DESCRIPTION AND OPERATION OF TIE RODS
Tie rods on the GT are connected to both rack ends
by means of a ball joint. Two rubber bellows between
ball joint and steering gear housing protect rack and
ball joints against dirt, dust and mud. The ball joints
of the tie rods do not require service.
Tie rods on the Opel l&O and Manta are connected
to both rack ends by means of a axial joint. Two
rubber bellows between the axial joint and steering
gear housing protect the rack and axial joints against
dirt, dust, and mud. The ball joint of the tie rod ends
on the Opel 1900 and Manta are maintenance free
and must not be disassembled.
MAJOR REPAIRREMOVAL AND INSTALLATION OF TIE RODS
38-2
RemovalFigure
38-2 Removing Ball Stud
In order to avoid the possibility of dirt entering the
steering gear assembly via the rack, it is recom-
mended that rods and area immediately surrounding
the gear assembly be wiped free of loose dirt prior to
removal.3. Remove clamp securing one end of rubber bellows
to tie rods and slip bellows off tie rods to expose nut
or lock plates. See Figure
3B-3.1. Remove cotter pins securing nuts on tie rod ends
and remove nuts. Discard cotter pins.4. On the GT, bend up round edges of lock plate
from tie rod ball studs and unscrew ball studs From
rack. See Figure
3B-4.

3C-22 1973 OPEL SERVICE MANUAL.
FRONT END ALIGNMENT
CONTENTS
SubjectPage No.
DESCRIPTION AND OPERATION:
FrontWheelAlignment
. . . . . . . . . . . . . . . . . . . . . . ..“...........................DIAGNOSIS: (Not Applicable)
MAINTENANCE AND ADJUSTMENTS:
Inspection Before Checking Front Wheel Alignment
AdjustingCaster
. . . . . . . . ...’ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Adjusting Camber
. . . . . . . . . . . . . . . . . . . . . . . . . . * . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Adjusting Toe-In
. . . . . . . . . . . . . . * . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .King Pin Inclination
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MAJOR REPAIR: (Not Applicable)
SPECIFICATIONS:3C-223C-223C-233C-253C-253C-26
Wheel Alignment Specifications
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3C-26
DESCRIPTION AND OPERATIONFRONT WHEEL ALIGNMENT
Wheel alignment is the mechanics of adjusting the
position of the front wheels in order to attain the
least steering effort with a minimal amount of tire
wear.handling, but require only reasonable accuracy to
provide normal tire life. With the type of front sus-
pension used, the toe-in adjustment is much more
important than caster and camber are as far as tire
wear is concerned.
Correct alignment of the chassis is essential to proper
alignment of front and rear wheels. Briefly, the es-
sentials are that the frame must be square in plain
view within specified limits, that the top and bottom
surfaces of the front cross member must be parallel
fore and aft, and that the upper and lower control
arm must be at correct location in respect to shafts
and the front cross member. All bushings, ball joints
and bolts must be of proper torque and in usable
condition.Caster and camber adjustments need not be consid-
ered unless visual inspection shows these settings to
be out, or unless the car gives poor handling on the
road. In the majority of cases, services consisting of
inflating tires to specified pressure and interchanging
tires at recommended intervals, balancing all wheels
and tires, adjusting steering gear and setting toe-in
correctly will provide more improvement in car han-
dling and tire wear than will other front end align-
ment adjustments.
Wheel and tire balance has an important effect on
steering and tire wear. If wheels and tires are out of
balance, “shimmy” or “tramp” may develop or tires
may wear unevenly and give the erroneous impres-
sion that the wheels are not in proper alignment. For
this reason, the wheel and tire assemblies should be
known to be in proper balance before assuming that
wheels are out of alignment.The correct use of accurate front end alignment
equipment is essential to determine whether front
suspension parts have been damaged by shock or
accident, and to obtain correct alignment settings
after new parts have been installed.
MAINTENANCE AND ADJUSTMENTS
Inspection Before Checking Front Wheel AlignmentClose limits on caster, front wheel camber, andBefore making any adjustment affecting caster, cam-
theoretical king pin inclination are beneficial to carber, toe-in, theoretical king pin inclination, or
steer-

3C-24 1973 OPEL SERVICE MANUAL
NOTE:
FRONT OF CAR
4Figure
3C-3 Upper Control Arm Shaft and Bushingsx.3
Figure
3C-4 Supporting Vehicle at Both Lower
Control Arms(B) (rear) between upper control arm and shock ab-
sorber support. See Figure
3C-5.5. One
.24” thick washer each is installed in produc-
tion on each car side. Consequently, only two adjust-
ments are possible by adding washers of different
thickness.
6. One
.12” in front and one .36” in the rear (caster
increase of 1 degree) or one
.36” in front and one. 12”
in the rear (caster decrease of 1 degree). Never addFRONT OF CAR
3G5
Figure
3C-5 Caster Adjustment Washer Location -Opel 1900 - Manta
several washers in one place. The washers B installed
in production have a larger outer diameter than the
washer A. For service, the Parts and Accessories
Department supplies only larger washers with an
outer diameter of 1.57”.
7. Insert control arm shaft from front towards the
rear into upper control arm and shock absorber
SUP-port. Observe that the crown of both plate washers
shows inwards. See Figure
3C-5.8. Torque hex nut of control arm shaft to 40 ft.lbs.
Always use new self-locking nut.
9. Torque wheel nuts to 75
ft.lbs.10. Recheck caster setting.

3C-26 1973 OPEL SERVICE MANUAL
1. Loosen lock nut of left and right tie rod and
slacken back nut.
2. Remove hose clamp for rubber bellows attach-
ment from respective axial joint and adjust toe-in by
turning axial joint. When doing this, observe that the
rubber bellows, having a tight seat on thejoint, is not
twisted. If necessary, lubricate seat of bellows and
hold back bellows when turning. See Figure 3C-7.Figure
3C-7 Adjusting Toe-In Opel 1900 Manta
3. Toe-in should be l/S”
- 3/16”.
4. Torque lock nut of left and right tie rod to 47
ft.lbs.5. Attach respective rubber bellows with hose clamp,
making sure that clamp bolt points towards the
front. The rubber bellows must not be twisted, i.e.,
SpecificationsFRONT END ALIGNMENTthe individual grooves of bellows must be in vertical
position.
6. After adjustment, turn steering several times to the
left and right to determine if a proper attachment of
both rubber bellows to the steering gear housing is
warranted.
CHECKING THEORETICAL KING PIN
INCLINATION
When checking theoretical king pin inclination, car
must be on a level surface, both transversely and fore
and aft, must have trim heights within limits, and
must be at curb load.
With camber known to be within specitied limits,
theoretical king pin inclination should check to 8.5
degrees for Opel 1900
- Manta, and 6 degrees for GT.
If camber is incorrect beyond limits of adjustment
and theoretical king pin inclination is correct, or
nearly so, a bent steering knuckle is indicated.
There is no adjustment for theoretical king pin incli-
nation as this factor depends on the accuracy of the
fronts suspension parts. Distorted parts should be re-
placed with new parts.
The practice of heating and bending front suspension
parts to correct errors must be avoided as this may
produce soft spots in the metal in which fatigue and
breakage may develop in service.
MODELCASTER
’CAMBER ’TOE-INOUTER WHEEL
MIN.. MAX.WHEN INNER
WHEEL AT 20
’1900‘3
l/2-61/2-1?1/2I/% - 3/1619 l/4GT3+1
1+1/2l/32 - l/818 l/2* Permissable deviation from left to right wheel
- maximum 1”.

3D. 281973 OPEL SERVICE MANUALr
LFLEXIBLE
COUPLING
SHAFT.
NEEDLE BEARING
L
LPINION BUSHING
O-RING SEAL
Figure
3D-2 Steering Gear Assembly - End View
3D-2RACK GUIDE
rBUSHINGFigure
3D-3 Steering Gear Assembly Front View
until a resistance is felt. By threading in adjusting
screw when steering gear is set to highpoint, the
MAJOR REPAIRsintered bronze she0
l’s pushed against the rack SO
that the rack is blocked.
REMOVAL AND INSTALLATION OF STEERING
3. Back off adjusting screw
l/8 to l/4 of a turn.GEAR ASSEMBLY AND TIE RODS
4. Tighten lock nut to a torque of 43 lbs.ft.
Removal. GT5. Fill area under pinion shaft rubber boot with steer-
ing gear lubricant and slide boot into position.1. Remove rubber knee protector pad.

3D- 301973 OPEL SERVICE MANUALFigure 3D-8 - Removing Clamp Bolt3. Remove cotter pin located on left and right tie rod
end and unscrew nut.
4. Using Tool J-21687, press tie rod ends out of
steering arms.
5. Disconnect steering gear housing from front sus-
pension cross member and remove steering gear
together with tie rods.
Installation . GTCAUTION: Fasteners are important attaching parts in
that they could affect the performance of vital com-
ponents and systems, and/or could result in major
repair expense. They must be replaced
with one of
the same part number or with an equivalent part if
replacement becomes necessary. Do not
use a re-
placement part of lesser quality or substitute design.
Torque values must be used as specified during reas-
sembly to assure proper retention of these parts.
1. Position steering gear on front suspension cross
member and torque attaching bolts to 18
lb.ft.2. Position tie rod ball studs in steering arms; install
nuts and torque to 29 lb.ft. Lock in position with new
cotter pins.
3. Fully turn steering wheel so that flat or cutout
surface on lower portion of steering shaft is parallel
to flexible coupling bolt hole.
4. Install the lower end of steering shaft to the flexi-
ble coupling and adjust dimension between steering
wheel hub and direction signal switch housing cover
to
l/8 and 3/32 inch. Maintain adjustment by tight-
ening flexible coupling bolt and nut to 15 lb.ft. Lock
the bolt and nut in position with lock-plate tabs.5. Reinstall stop bolt into steering column.
6. Full turn steering wheel both right and left. If any
resistance is noticeable, it will be necessary to remove
the sleering column and correct the cause.
D. Installation (Opel 1900. Manta)CAUTION: Fasteners are important attachingparts in
that they could affect the performance of vital com-
ponents and systems, and/or could result in
maJbrrepair expense. They must be replaced with one of
the same part number or with an equivalent part if
replacement becomes necessary. Do not use a re-
placement part oflesser
quaky or substitute design.
Torque values must be used as specified during reas-
sembly to assure proper retention of these parts.
1. Prior to installation, set steering gear to high
point. The steering wheel spokes point downwards in
an oblique angle. The elongated cutout of the lower
steering mast must coincide with the clamp bolt hole
of the pinion flange.
2. Position steering gear on front suspension cross
member and torque attaching bolts to 29 lb.ft.
3. Position tie rod studs in steering arms. Install nuts
and torque to 29
Ib.ft. Lock in position with new
cotter pin.
4. Install the lower end of the steering shaft to flexi-
ble coupling and torque clamp bolt to 22
lb.ft.5. Attach guard plate to both side members and
lower deflector panel.
DISASSEMBLY AND ASSEMBLY OF
STEERING GEAR ASSEMBLY WITH TIE RODS
Disassembly - GT1. Carefully clamp gear assembly in soft jaw vise and
slip clamps and rubber bellows off gear housing to
expose area where ball joint screws into rack.
2. Bend up round edges of lockplates from tie rod
ball studs and disconnect tie rod ball studs from rack.
See Figure
3D-9). It is important that rack be held
secure with open end wrench to prevent damage to
rack teeth.
3. Loosen adjusting screw lock nut; remove adjusting
screw from steering gear housing, and take out thrust
spring and sintered bronze shell. See Figure
3D-11.4. Rotate gear assembly in vise so that pinion shaft
portion of assembly is held by vise, and remove pin-
ion nut, flat washer, and special washer.