1973 OPEL GT-R automatic transmission

AUTOMATIC TRANSMISSION 7C-111
OIL PUMP /’ASSEMBLY
ASPklNG
I(ETAINERSNAP RING
PLIERS
h7C146
Figure 7C.15537. Turn oil pump and reverse clutch assembly so
that oil pump face is facing up.
38. Install oil pump gears using the location mark
made before disassembly.
39. Check the end clearance of both gears to the oil
pump face. Clearance should be between
.0005 to
.0035. See Figure 7C-156.Disassembly, Inspection and Reassembly of Second
Clutch
1. Remove ring gear retaining ring from second
clutch drum. See Figure X-157.
GEAR
Figure
7C-1572. Remove ring gear. See Figure
7C-158.
SECOND CLUTCH DRUM
:-157Figure
7C-15641. Replace the oil pump assembly if the end clear-
ance is not within specifications.Figure 76.158
3. Remove second clutch spacer plate retaining ring.
4. Remove second clutch spacer plate. See Figure7c- 159.

AUTOMATIC TRANSMISSION 7C-113
12. Inspect the piston return springs. Evidence of
extreme heat or burning in the area of the clutch may
have caused the springs to take a heat set and would
justify replacement of the springs.
Figure 7C-16313. Inspect second clutch hub bushing for scoring or
wear.14. If necessary, remove second clutch hub bushing
using remover and installer J-23130-6 with driver
handle J-8092. See Figure 7C-164.
P-J-6092
SECOND CLUTCH
DRUM
iJ:23130-6Figure
7C-16415. Clean in solvent to remove any foreign matter.
Install new second clutch hub bushing using tool
J-23 130-6 and driver handle J-8092. Bushing must be
driven in until tool bottoms on bench. See Figure 7C-
164.16. To install second clutch piston into second clutch
drum, use installer tool J-23080 so as not to damage
lip seal. See Figure 7C-165. Use liberal amount of
transmission fluid for ease of installation and to pre-
vent seal damage.
SECOND CLUTCHDRUM
J-23,060Figure
7C-16517. Remove second clutch piston and seal installer
J-23080.18. Install 22 springs and retaining seat on second
clutch piston.
19. Using spring compressor tool J-2590-12 with
adapter J-21420-1 on retaining seat, compress sec-
ond clutch piston return springs. Care should be
taken so that retainer does not catch in snap ring
groove and damage retainer.
20. Install snap ring with snap ring pliers such as
J-
8059.21. Install bronze thrust washer so that the tang seats
in the slot of the second clutch hub. Secure with
petroleum jelly (unmedicated).
22. Inspect condition of composition and steel plates.
Do not diagnose a composition drive plate by co/or.
A. Dry composition plates with compressed air and
inspect the composition surface for:
1. Pitting and flaking
2. Wear
3. Glazing

AUTOMATIC TRANSMISSION 7C-115INPUT SPRAG RACE
8 RETAINER ASSEMBLY/
GEAR
CLUTCH HUBFigure
7C-1693. Push sprag assembly and retaining rings from
sprag race and retainer. See Figure
7C-170.Figure
7C.17 I7. Remove snap ring using snap ring pliers such as
J- 8059. See Figure 7C-172.SPRAG RACE
-AND RETAINER
,, SPRAG ASSEMBLY
\Figure
7C-1704. Remove third clutch plates from third clutch
drum. See Figure
7C-171. The plates should be kept
in the same sequence as they were installed in the
clutch.
5. Remove input shaft thrust washer and needle
thrust bearing. See Figure
7C-171.6. Using compressor tool J-23075 on third clutch
piston retaining seat, compress third clutch piston
return springs using arbor press.Figure 7C.172
8. Remove the retaining seat and 12 return springs.
9. Remove third clutch piston from third clutch
drum. See Figure
7C-174.
10. Inspect third clutch piston return springs. have
caused the springs to take a heat set and would jus-
tify replacement of the springs.
11. Inspect check ball in third clutch piston. If ball
is missing or falls out upon inspection or piston is

AUTOMATIC TRANSMISSION 7C-117WIRE CRIMPED
INTO COPPERTUBING
Figure 7C-178
19. Inspect condition of the third clutch composition
and steel plates. Do not diagnose a composition
drive plate by color,A. Dry composition plates with compressed air and
inspect the composition surface for:
1. Pitting and flaking
2. Wear
3. Glazing
4. Cracking
5. Charring
6. Chips or metal particles imbedded in lining
If a composition drive plate exhibits any of the above
conditions, replacement is required.
B. Wipe steel plates dry and check for heat discolora-
tion. If the surface is smooth and an even color smear
is indicated, the plates should be reused. If severe
heat spot discoloration or surface
scutXng is in-
dicated, the plates must be replaced.
20. Install third clutch plates into third clutch drum
beginning with a steel plate, composition plate, steel
plate, composition plate, etc. Use a liberal amount of
transmission fluid.
21. Inspect thrust washer and needle thrust bearing
for damage. Replace if necessary.
22. Install thrust washer and bearing onto input
shaft. Secure with petroleum jelly (unmedicated).23. Inspect sprag assembly for wear, damage orsprags that freely fall out of cage. Inspect input sun
gear for chipped or nicked teeth or abnormal wear.
Replace part if necessary.
24. Install sprag onto third clutch hub with groove
on sprag cage outer diameter toward input sun gear.
See Figure
7C-179.Figure 7C-179
25. Install sprag race and retainer assembly over
sprag assembly. Holding input sun gear with left
hand, sprag race and retainer assembly should “lock
up” when turned with right hand in a clockwise
direction and should rotate freely when turned coun-
terclockwise. See Figure
7C-180.Figure 7C-180

AUTOMATIC TRANSMISSION 7C-121
Fig 7C-192Figure 7C-194
6. Inspect cushion spring, adjusting bolt, and piston
sleeve for damage. Inspect piston for damage and
piston ring for side wear, replace if necessary.
7. Reassemble servo piston, reversing disassembly
procedure.Disassembly, Inspection and Reassembly of Valve
Body1. Remove the manual valve and manual valve link
from the valve body.
2. Turn the valve body so that the transfer plate is
facing upward and remove the two bolts holding the
transfer plate to the valve body. See Figure
7C-196.3. Remove transfer plate and gasket.
Figure 7C-193
3. Depress servo piston sleeve and remove piston
sleeve retaining ring.
4. Push sleeve through piston and remove cushion
spring and spring retainer.
5. Remove servo piston ring4. Using small C-clamp on valve body, compress
accumulator piston.
5. Remove the accumulator piston retaining ring
with screw driver. See Figure
7C-198.6. Carefully loosen C-clamp as accumulator piston is
under spring tension.

7. Remove accumulator piston, oil ring, and spring.
See Figure 7C-200.ACCUMULATOR PISTON
Figure 7C-200AUTOMATIC TRANSMISSION 7C-123
8. Inspect accumulator oil ring for damage or edge
wear and piston for damage. Replace if necessary.
For steps 9 through 21 refer to Figure 7C-201.9. Remove 1-2 Shift control valve retaining pin, l-2
shift control valve sleeve, control valve, 1-2 shift
valve spring and valve. It may be necessary to
remove burrs in valve body bore made by retaining
pin prior to removal of the sleeves and valves.
10. Remove the 2-3 Shift control valve retaining pin
and sleeve. Also, remove the 2-3 shift control valve,
spring seat, spring and 2-3 shift valve.
11. Remove the 3-2
,control valve retaining pin and
plug. Remoye 3-2 control valve spring and control
valve.12. Remove the detent pressure regulator valve re-
taining pin, spring, and detent pressure regulator
valve.13. Remove the high speed downshift timing valve
retaining pin and spring and remove valve.
1.RETAINING PIN
2.1-2 SHIFT CONTROL VALVE SLEEVE
3.1-2 SHIFT CONTROL VALVE
4. l-2 SHIFT CONTROL VALVE SPRING5.1-2 SHIFT VALVE
6.RETAINING PIN
7.2-3 SHIFT CONTROL VALVE SLEEVE
8.2-3 SHIFT CONTROL VALVE9.2-3 SHIFT CONTROL VALVE SPRING
IO. 2-3 SHIFT CONTROL VALVE SPRING SEAT
11.2-3 SHIFT VALVE
12.1-2 ACCUMULATOR VALVE SPRING13.1-2 ACCUMULATOR VALVE
14.RETAINING PIN
15.1-2 ACCUMULATOR VALVE PLUG16.RETAlNlNG PIN
17.3-2 CONTROL VALVE PLUG18.3-2 CONTROL VALVE SPRING
d 28 29 31 32 33uu44ucBBt?a~~19. 3-2 CONTROL VALVE
20. REVERSE CONTROL VALVE
21. MANUAL LOW CONTROL VALVE
22. MANUAL LOW CONTROL VALVE SPRING
23. RETAINING PIN
24. RETAINING PIN
25. DETENT PRESSURE REGULATOR VALVE SPRING
26. DETENT PRESSURE REGULATOR VALVE
27. MANUAL VALVE
28. LOW SPEED DOWNSHIFT TIMING
VALVE SPRING
29. LOW SPEED DOWNSHIFT TIMING VALVE
30. RETAINING PIN
31. TIMING AND CONTROL VALVE PLUG
32. HIGH SPEED DOWNSHIFT TIMING VALVE
33. HIGH SPEED DOWNSHIFT TIMING
VALVE SPRING
34. RETAINING PIN
7c-201Figure 7C-201 Valve Body
- Exploded View

AUTOMATIC TRANSMISSION 7C-1251. CASE VENT4.3RD CLUTCH7.SUCTION
2. CONVERTER OUT5MODULATOR8.LINE/3.2ND CLUTCH
6. BOOST9.REVERSEFigure 7C-202 Case Front View Oil Passage
Identification
7.
!nspect reaction sun gear drum bushing sleeve
inside case at rear for scoring. If necessary, replace
sleeve before installing rear case bushing.
8. Remove sleeve by grinding. Care must be used in
order that aluminum case is not damaged when
grinding sleeve.
9. Install new sleeve using installer tool J-23130-7
and driver handle J-8092.
10. Install new case bushing using remover and in-
staller tool J-23130-3 and driver handle J-8092.
Bushing should be installed flush with case at rear.
See Figure
7C-203.Figure 7C-2031. Drain Converter. If clutch disc material or
foreign matter has been found while draining con-
verter,
replace entire converter assembly as it can not be
cleaned properly.
2. Air check converter for leaks using converter
checking tool J-21369. Install tool and tighten. Ap-
ply 80 psi air pressure to tool. See Figure
7C-204.Figure 7C-204
3. Submerge in water and check for leaks.
4. Check converter hub surfaces for scoring or wear.
Installation of Selector Lever and Shaft1. Install new selector lever shaft oil seal in case.
Insert selector lever shaft through case from outside.
Care should be exercised so that oil seal is not da-
maged. See Figure
7C-206.2. Insert spring pin in case to secure selector lever
shaft.3. Guide selector lever over shaft and secure with
lock nut.
4. Insert parking
paw1 actuator rod from front of the
case and through hole in case at rear. See Figure 7C-
207.5. Install parking
paw1 actuator rod retaining ring.
Installation of Low Band1. Turn transmission case so that front of case is
upward.

AUTOMATIC TRANSMISSION ?C-127
INPUT SHAFT
Figure 7C-208
1. Place needle thrust bearing race on rear of
case around the case bushing. Secure with petroleum
jelly (unmedicated).
2. Place needle thrust bearing on race. See Figure 7C-
209. Secure with petroleum jelly (unmedicated).
Figure 7C-2093. Insert reaction sun gear and drum into band with
reaction sun gear facing upward.
4. Place needle bearing on first then race on front
face of reaction sun gear. See Figure
7C-210. Secure
with petroleum jelly (unmedicated).Figure
7C-2 10
Installation of Output Shaft and Planetary Carrier
1. Install input sun gear to planetary carrier washer
and bearing into carrier. Secure with petroleum jelly
(unmedicated).
2. Insert output shaft and planetary carrier assembly
from front of case to spline with reaction sun gear.
See Figure
7C-211.Figure
7C-2 1 1Installation of 2nd and 3rd Clutch Assemblies Into
Case
1. With second clutch assembly on bench, align sec-
ond clutch drive plates in second clutch drum.