1973 OPEL GT-R wheel

3A- 41973 OPEL SERVICE MANUAL
The two cross-members to body supports are at-
tached to the horizontal part of the cross-member
with two bolts. The oufererbolt serves simultaneously
as support for the lower control arm. As the bolt is
inserted from the front, the cross-member to body
support can be removed without the lower control
arm. The inner bolt attaches simultaneously to the
steering.
The stabilizer is U-shaped and supported in rubber
bushings in the two cross-members to body supports.
The complete front suspension is attached to the
underbody in four places.
The engine damper blocks are bolted to the inside of
the inclined parts of the cross-member.
The front wheel bearings are roller bearings.
All front suspension joints are maintenance-free.
MAINTENANCE AND ADJUSTMENTSFRONT WHEEL BEARING ADJUSTMENT
1. If wheel has not previously been removed from the
car, remove grease cap, cotter pin, and spindle nut.
Discard cotter pin.
2. Torque spindle nut to 18
lb.ft. while rotating
wheel. This will allow the bearings to settle.
3. Back offspindle nut
l/4 turn. If slot and cotter pin
hole are staggered, further back off nut
l/l2 turn,
but do not tighten, until next slot in nut is in align-
ment with hole in spindle. Install new cotter pin. A
properly adjusted wheel bearing has a small amount
of end play and a loose nut when adjusted in the
above manner.
MAJOR REPAIRREMOVAL AND INSTALLATION OF FRONT
SUSPENSION
(COMPLETE ASSEMBLY)
Removal GT1. Prior to raising front end of car, apply parking
brake and block rear wheels.
2. Raise front end of car with a jack. It is recom-
mended that a wood block be placed between thejack and the front cross member to prevent damage
to the cross member.
3. Support front end of car by placing floor standsunde:r jacking brackets.
4. Support engine-transmission assembly in upper-
most position with jack stand at rear of engine, or an
alternate method would be to use Engine Holding
Fixture, Tool J-23375. See Figure 3A-5.
Install tool by removing upper kngine mount nut and
installing fixture. Replace nut and tighten. The en-
gine will now be supported by the tool between the
frame rails.
Figure
3A-5 Engine Holding Fixture Installed
5. Loosen steering mast at the lower universal joint
and take out clamp bolt. Loosen clamp at the upper
universal joint and lift steering mast upwards until it
is free at the lower universal joint. See Figure
3A-6.6. Disconnect brake lines at brake hose.
7. Disconnect shock absorber at upper mounting. It
is necessary to remove air cleaner. See Figure
3A-24.8. Disconnect engine mounts at cross member.
9. Remove front suspension cross member attaching
nuts and lower the cross member.
Removal Opel 1900 - Manta1. Prior to raising front end of car, apply parking
brake and block rear wheels.

FRONT SUSPENSION3A- 5
Figure 3A-6 GT Steering Mast Joint
2. Install Hooks J-23697 before jacking up car to
assure proper loading of suspension bushings and
mounts. See Figure
3A-7.3. Raise front of vehicle and support with stands.
4. Remove front wheels.
5. Remove guard plate. See Figure
3A-8,6. Remove brake line retainers on both sides. The
brake system remains closed. Unscrew brake calipersand suspend them in wheel house.Figure
3A-9 Removing Guard Plate
7. Suspend engine with a suitable engine lifter, simi-
lar to the one shown in Figure
3A-9.8. Unscrew lower steering mast clamp bolt out of
pinion flange. See Figure
3A- 10.
9. Unscrew front left and right engine mount from
damper block.
10. On top and in the rear, unscrew front suspensionFigure
3A-7 Installing Hooks J-23697Figure 3A-9 Suitable Engine Liftel

3A- 6 1973 OPEL SERVICE MANUAL
Figure 3A-10 Steering Mast Clamp Bolt
assembly at the cross member to body support from
frame and let it down onto jack. See Figure
3A-11.
Figure 3A-1 1
Installation
GT
CAUTION: Fasteners are important attachingparts in
that they could affect the performance of vitaI com-
ponents and systems, and/or
coo/d result in major
repair expense. They must be replaced with one of the same part number or with an equivalent part if
replacement becomes necessary. Do not use a re-
placement part or lesser quality or substitute design. Torque
values
must be used as speciiied during reas-
sembly to assure proper retention of these parts.
I. Support front suspension and cross member on
jack and raise into position.
2. Attach cross member to front frame rail. Torque
to 36
lb.ft.
3. Install engine mounting nut? Remove engine sup-
port.
4. Install shock absorber mounting bolts and install
air cleaner.
5. Connect brakes hoses and bleed brakes as outlined
in Group 5.
6. Install radiator mounting bolt in support cross
member.
7. Push steering column downwards until a
l/8”
clearance is obtained between steering wheel hub and
switch cover.
8. With steering wheel in centered position and front
wheels straight ahead, tighten the clamp bolt at the
lower universal joint to 22
fbs.fi. and the clamp at
the upper universal joint to 14
lbs.ft. See Figure
3A-6.
9. Inr;tall mast guide sleeve stop bolt. Always install
new lock plate. See Figure
3A-7.
10. Remove front support stands and lower vehicle.
Installation Opel 1900 - Manta
1. With jack, lift up front suspension assembly so
that the individual attaching points coincide. At the
same time, insert lower steering mast into pinion
flange. See Figure
3A-12.
2. In the rear bolt cross member to body support.
Torque to 58
ft.lbs. When doing this with a suitable
tool, counterhold damper bushing which is installed
in a certain position, to prevent it from turning. For
this purpose, detach heat
deflectqr plate on right
vehicle side.
3. Torque front suspension assembly to frame attach-
ment to 47
ft.lbs.
4. Torque lower steering mast to pinion flange at-
tachment clamp bolt to 22
ft.lbs.
5. Reinstall both brake calipers. Torque to 72 ft.lbs.
Install brake line retainer.
6. On both sides install upper control arm ball joint.
Torque bolts to 29
ft.lbs.

FRONT SUSPENSION3A- 7
Figure 3A-12 Front Suspension Attaching Points
Always use new self-locking nuts.
7. Reinstall guard plate.
8. Crosswise torque wheel nuts to 65 ft.lbs.UPPER BALL JOINT REMOVAL AND
INSTALLATION
RemovalI. Place jack under spring eye and raise car. Remove
wheel from car.
2. Remove cotter pin and castle nut from upper ball
joint stud. Discard cotter pin.
3. Press ball stud from steering knuckle using puller
J-21687, and remove two (2) bolts attaching ball
joint to upper control arm. See Figure 3A-13.
4. If dust cap on upper ball joint is torn or missing,
the ball joint should be replaced.
Installation
CAUTION:
Fasteners are important attachingparts in
that they could
afEct the pertkmance of vital com-
ponents and systems, and/or could result in major
repair expense. They must be replaced with one of
the same part number or with an
equivaknt pa-t if
replacement becomes necessary. Do not use a re-
placement part of lesser quality or substitute design.
Torque values must be used as specified
durikg reas-
sembly to assure proper retention of these parts.Figure 3A-13 Upper Ball Joint
1. Install upper control arm ball joint with the off
center holes in flange showing towards the steering
knuckle spindle.
2. Install two (2) bolts attaching ball joint to upper
control arm. Torque nuts to 29 Ibft.
3. Install upper ball joint stud in%eering knuckle
and torque castle nut to 29
Ib.ft. on GT and 40 lb&.
on Opel
1900 - Manta.
4. Install new cotter pin, and replace wheel.
5. Always check caster and camber after installing
new ball joints.
LOWER BALL JOINT REMOVAL AND
INSTALLATIONNew lower ball joints have an axial play of up to
,020inch. The maximum permissible axial play of older
ball joints is
,080 inch. At an axial play of more than
,080 inch, the lower ball joint must be replaced. If the
dust cap is torn, loose, or missing, the lower ball joint
must also be replaced. See Figure
3A-14.The lower ball joints are checked for wear by using
Checking Gauge J-23402 for the GT, and using
Checking Gauge J-23745 for the Opel 1900
- Manta.
See Figure
3A-15.
Removal GT1. Raise car and support at rear of front frame rails.
2. Remove front wheel.

FRONT SUSPENSION3A- 9
8. Press ball stud out of lower control arm.Removal Opel 1900 - MantaBefore raising vehicle, install Hooks J-23697 on re-
spective vehicle side to cross member and upper con-
trol arm. See Figure 3A-7.
1. Raise car and support at rear of front frame rails.
2. Remove front wheel.
3. At the lower control arm ball joint, remove castle
nut cotter pin and slacken back nut so that the thread
can no longer be damaged.
4. With a suitable drift, detach ball joint from steer-
ing knuckle. With jack, lift up lower control arm,
unscrew castle nut and remove Hooks J-23697.
5. Unscrew upper control arm ball joint and suspend
front wheel hub and brake caliper in wheel house. Do
not turn upper control arm ball joint flange, as this
would result in a change of camber.
6. Remove defective lower control arm ball joint
using Tools J-9519 and Receiver J-23754.
Installation GT
CAUTION:
Fasteners are important attachingparts in
that they could affect the performance of
vitaI com-
ponents and systems, and/or could result in
ma&r
repair expense. They must be replaced with one of
the same part
numer or with an equivalent part if
replacement becomes necessary. Do not use a
re-
placement part of lesser quality or substitute design.
Torque values must be used as specified during reas-
sembly to assure proper retention of these parts.1. When pressing the ball joint in place, make certain
the locating notch in the lower rim of the ball joint
matches the alignment reference mark placed on the
lower control arm prior to removal. The notch in the
ball joint bottom plate, identifying the direction of
the elongated slot, must point towards the brake
drum backing plate. See Figure
3A-17. Alignment
must be within 2 degrees of lower control arm center-
line. If proper positioning of the ball joint is not
accomplished, the result is a limitation of the neces-
sary ball stud movement. If ball stud movement is
limited, an interference between the ball stud and
housing is created, and binding or even fracture may
occur. Replacement ball joints may or may not have
marking notch as shown in Figure
3A-20. If it does
not have a marking notch, the joint is completelysymetrical and may be installed in any position.
When pressing in ball joint do not press on bottom
plate, but on ball joint housing only.2. Install dust cap on lower ball joint and fill with
chassis lubricant. Attach dust cap retainer.
3. Press ball joint into steering knuckle. Use
J-9519-3 as installer and J-21690 as a supporting
sleeve.4. Install castle nut on ball joint stud and torque to
40
Ib.ft. Install new cotter pin.
5. Reconnect shock absorber to lower control arm
and torque to 30 lb.ft.
6. Remove spring compressor.
7. Install front wheel, and lower the car.
8. Always check caster and camber after ball joint
replacement.
Installation Opel 1900 - Manta
CAUTION:
Fasteners are important attachingparts in
that they could
aff’ect the performance of vital com-
ponents and systems, and/or could result in
ma&r
repair expense. They must be
rep/aced with one of
the same part number or with equivalent parts, if
rep/acement becomes necessary. Do not use a re-
p/acement part of lesser quality or substitute design.
Torque valves must be used as
specitied during reas-
sembIy to assure proper retention of these parts.1. Drive new ball joint into lower control arm using
Tools J-9519 as installer and J-23755 as a supporting
sleeve. Do not strike onto ball joint bottom.
The ball joint is maintenance-free. It is supplied as an
assembly only and cannot be disassembled further.
2. On new lower control arm ball joint, make sure
that the marking groove in the housing bottom in
alignment with the axis of the lower control arm.
Permissible deviation: minus 2 degrees to plus 2 de-
grees.This is required, to obtain the maximum freedom of
movement of the ball stud in the housing. See Figure
3A-18.3. Attach steering knuckle together with front wheel
hub and brake caliper to lower control arm ball joint.
Torque castle nut to 54
ft.lbs.4. Attach ball joint to upper control arm and torque
to 29
ft.lbs. Always use new self-locking nuts.
5. Install wheel and tighten nuts to a torque of 65
ft.lbs.6. Lower car and check caster and camber.

3A- 101973 OPEL SERVICE MANUAL
Figure 3A-18 Lower Ball Joint Notch Opel 1900 -
MantaUPPER CONTROL ARM REMOVAL AND
INSTALLATION
Removal GT1. Raise car and support at rear of front frame rails.
2. Remove front wheel.
3. Install spring compressor and compress spring
until there is 3-l/8” between compressor and lower
spring leaf.
4. Remove cotter pin and castle nut from upper ball
joint stud. Discard cotter pin.
5. Use tie rod remover J-21687 remove ball jointfrom.steering knuckle. 6. Support brake drum to
relieve tension on brake hose.
7. Remove hex nut from upper control arm shaft.
Remove shaft and washers from shock absorber sup
port. Do not damage threads on control arm shaft.
8. Remove control arm from car. Do not lose inner
toothed washers. Note size and location of toothed
washers.Removal
Opel 1900 . Manta
1, Raise car and support at rear of front frame rails.
2. Remove front wheel
3. Unscrew upper control arm to cross member
self-locking attaching nut.4. Unscrew ball joint from upper control arm. Do not
turn upper control arm ball joint flange, as this
would result in a change of camber.
5. Support front wheel hub so that brake hose is not
stressed.6. Pull out upper control shaft to cross member at-
taching bolt and remove control arm. Shims have to
be reinstalled in their original location to maintain
the proper caster setting.
Installation GT
CAUTION:
Fasteners are important attaching parts in
that they could affect the the
perfonmmce of vital
components and systems, and/or could result in ma-
jor repair expense. They must be replaced with one
of the same part number or with an equivalent part
if replacement becomes necessary. Do not use a re-
placement part or lesser quality or substitute design.
Torque values must be used as specified during reas-
sembly to
assure proper retention of these parts.If rubber bushings on control arms are worn, arms
must be replaced.
1. Slide rubber rings over bushings. Slide rings over
inner sleeves of bushings. Place control arm in posi-
tion on shock absorber support, installing toothed
washers in their original positions. See Figure 3A-
19.2. From front to rear, install control arm shaft. If
necessary, align washers and control arm bushings
with a small drift prior to installing control arm
shaft. See Figure
3A-19.3. Tighten hex nut on control arm shaft finger tight.
4. Increase tension on spring compressor in order to
relieve tension on control arm shaft. Then torque hex
nut on control arm shaft to 33
Ib.ft.5. Press ball joint stud into steering knuckle and
torque castle nut to 29 lb.ft. Install new cotter pin.
6. Remove spring compressor and lower car.
7. Check front end alignment.
Installation Opel 1900. Manta
CAUTION:
Fasteners are important attaching parts in
that they could at?&
the performance of vital com-
ponents and systems, and/or
coo/d result in major
repair expense. They must be replaced with one of
the same part number or with equivalent parts, if
replacement becomes necessary. Do not use a
re-

FRONT SUSPENSION3A- 11UPPER CONTROL ARM SHAFT
INNER SLEEVE
OUTER SLEEVE
RUBBER DAMPENIN
GUIDE SLEEVE
ABSORBER SUPPOR
SHOCK ABSORBER SUPPORT
ON FRONT SUSPENSION
CROSS MEMBER
-TOOTHED WASHER
l-UPPER CONTROL ARM
RUBBER BUSHINGS
PLATE WASHER
Figure
3A-19 Upper Control Arm Shaft and Bushings
placement part of lesser quality or substitute design.
Torque
valves must be used as specified during reas-
semb/y to assure proper retention of these parts.1. On installation of the upper control arm, make
sure that damper bushing with the rubber shoulder
on both sides is always located in the rear.
2. Attach upper control arm to cross member and
torque to
40 lb.ft. Always use new self-locking hex
nut. The upper control arm must be tightened in
horizontal position only. This applies also to all other
attaching joints in connection with rubber damper
bushings in the control arms of the front suspension
so that the rubber parts under load are in an almost
twist-free condition. This position exists, if the hooks
J-23697 are used.
3. Attach ball joint to upper control arm and torque
to 29
lb.ft.4. Install wheel and torque nuts to 65
lb.ft. Lowercar.LOWER CONTROL ARM REMOVAL AND
INSTALLATION
Removal GT
1. Raise car and support at rear of front frame rails.
2. Remove front wheel.
3. Remove cotter pin from castle nut on ball joint
stud and back off castle nut two (2) turns. Hit ball
stud a sharp blow to break it loose. DO NOT
REMOVE NUT.
4. Install spring compressor (J-21689) and compress
spring until a distance of
3-l/8 inches is achieved
between spring compressor and lower spring leaf.
5. Disconnect and compress shock absorber.
6. Support rail of spring compressor with a jack.
Remove lower control arm from frame cross mem-
ber. Nuts may have to be removed with a punch. See
Figure 3A-20. Discard the lock nuts.
7. Remove lower ball joint stud nut. Slightly lower

3A- 121973 OPEL SERVICE MANUAL
Figure 3A-20 Lower Control Arln Attachment
jack so that spring and lower control arm assembly
is removed from the front cross member and steering
knuckle.
8. Lower jack, spring compressor, and front spring
with control arm assembly. Remove lower control
arm to spring nuts.
9. Release spring compressor and remove controlarm attaching bolts and control aRn.
Removal Opel 1900. Manta1. Prior to raising car, install upper control arm
hooks J-23697.
2. Raise car and support with stands. Hoist should
be left in the raised position to maintain pressure on
lower control arm.
3. Remove front wheel.
4. Detach both stabilizer supports from cross mem-
ber to body support.
5. In lower control arm, remove self-locking hex
head bolt from stabilizer support and remove
washer.6. Using a pry bar, pry stabilizer bar out of lower
control arm support.
7. Remove shock absorber.
8. At lower control arm ball joint, remove castle nut
cotter pin and remove nut.
9. With suitable drift, detach lower control arm ball
joint from steering knuckle.10. Loosen nut that retains lower control to front
cross member.
11. Slowly lower hoist to release spring tension.
12. Swing lower control arm downwards and remove
front spring.13. Remove nut that retains lower control arm to
front cross member and remove lower control arm.
Installation GT
CAUTION:
Fasteners are important attaching parts in
that they could affect the performance of
vital com-
ponents and systems, and/or could result in
major
repair expeme. They must be replaced with one of
the
same part number or with an equivalent part if
replacement becomes necessary. Do not use a re-
placement part of
lesser quality or substitute design.
Torque values must be used as specified during
reas-
sembly to assure proper retention of these parts1. Attach lower control arm to front spring eye.
Torque bolts to 18
1b.R.2. Install spring compressor and with a jack raise
spring compressor with spring and control arm as-
sembly into position for pressing ball joint into steer-
ing knuckle.
3. Press ball joint into steering knuckle. Use
J-;lYN;: as installer and J-21690 as a supporting
4. Install castle nut on ball joint stud and torque to
54
lb.ft. Install new cotter pin.
5. Attach lower control arm to frame cross member
using new lock nuts.