AIR CONDITIONER SYSTEM -OPEL 1900 - MANTA9B- 91FAN DOES NOT RUN Correct electrical fault.
FAN RUNS
- Check air velocity.
NOT OK Clean evaporator inlets.
Clean evaporator core.
Clean evaporator outlets.
OK Check refrigeration (refer to Refrigeration
Diagnosis Guide).
MAINTENANCE AND ADJUSTMENTS
ADJUSTMENT OF THERMOSTATIC SWITCHThe system makes use of a thermostatic switch with
a self-supporting air sensing capillary. This capillary
controls the switch by sensing the temperature of the
air leaving the evaporator fins.
Checking for Proper Operation
I. Install the gauge set and set up the vehicle as
described under FUNCTIONAL TESTING SYS-
TEM iti Refrigerant Components Section.
2. Movement of the temperature control knob
should result in a definite change in suction pressure
and cycling of the compressor clutch.
3. If compressor continues to operate regardless of
the knob adjustment, it indicates that the switch
points are fused, which will lead to evaporator
freeze- up. The switch should be replaced.
Adjusting Switch
If, after ihe foregoing checks, the switch seems to be
operating correctly, adjust for proper setting if neces-
sary, as
~follows:1. Set up car as described in FUNCTIONAL
TESTING SYSTEM in Refrigerant Components
Section.2. The suction side of the system, read on the low
pressure gauge, should pull down to the pressure
shown in the chart in SPECIFICATIONS in Refrig-
erant Components Section.
3. Remove the face plate retaining screws and
remove face plate assembly noting the position of the
air sensipg capillary so that it can be reinstalled in
the same location as when removed. See Figure 98.170. ,:Figure
98.170 Location of Air Sensing Capillary
4. Remove the thermostatic switch retaining screws
and remove switch. Remove the non-metal end plate
from the switch to gain access tq the switch adjusting
screw. Check the screw for stripped or otherwise
damaged threads.
5. If the low side pressure
was less than the pre-
scribed pressure at the end of each cooling cycle, turn
the adjusting screw a partial turn clockwise. See Fig-
ure
9B-171.Figure 9B-17 1 Adjusting
Thkmosfatic Switch
6. If the pressure was more than the prescribed
value, turn the adjusting screw counter-clockwise.
7. Reinstall switch end plate and install switch in
face plate. Install face plate on ,evaporator assembly
assuring that the air sensing
c&pillary has been re-
placed properly.
8. Check system performance. Fffurther adjustment
is needed, repeat steps 3 thru 7 until the correct
pressure is reached.
Do not attempt to run a performance test with the
face plate and switch removed
,from the evaporator
assembly
- inaccurate reading, will result. Always
replace the switch and face plate assemblies before
checking the system performance.
AIR CONDITIONER SYSTEM - GT96. 97
AIR CONDITIONER SYSTEM
GTCONTENTS
Subject
: DESCRIPTION AND OPERATION:
General Description of System
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Operation of Controls
. . . . . , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .DIAGNOSIS:
Diagnosis Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MAINTENANCE AND ADJUSTMENTS:
Adjustment of Thermostatic Switch
. . . . . . . . . . . . . . . . . . . . . . .MAJOR REPAIR:
Removal 8 Installation of Vacuum Switch.
Removal&InstallationBlowerSwitch. . . . . . . . . . . . . . . . . . . . . .Removal & Installation Temperature Control Switch
. . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , . . . . . . . . . . . . . . . .
Removal&InstallationResistor Assembly. . . . . . . . . . . . . .Removal & Installation Blower Motor Assembly . .
SPECIFICATIONS:
Specifications
. . .
. . . . . . . . * . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page No.
9BL 97
9Bi 97
9BL 98
98: 98
9B: 99
9B; 99
9B- 99
98~10098-101
9B-104
DESCRIPTION AND OPERATIONAir Knob
GENERAL DESCRIPTION OF SYSTEMTurning the AIR knob clockwise operates the three-
speed blower motor.
The air &mditioner is intended to give maximum
cooling comfort within the vehicle. To do this, care-
ful attention must be given to the following sections.
The system operates on recirculated air only and is
entirely @dependent of the vehicle heater.Temp Knob
Recirculated inside air is drawn into the unit, passed
through the evaporator core and into the car through
the adjustable outlets in the duct assembly.This knob may be regulated to cohtrol the degree of
cooling desired. Fully clock-wise provides maximum
cooling; however, turning the kndb to the center de-
tent position provides adequate cooling for highway
operation.
CONTROLSWhen maximum cooling is reqlired, outside air
should not be admitted to the car.
System c&trols are the AIR knob controlling the
three
spe&d blower motor switch and the TEMPWhen the unit is set for maximum cooling and the
vehicle is being driven continuously at highway
knob which controls the setting of the thermostaticspeeds or at elevations of 4,000 ft. or more, there is
switch. When operating this system, the heater musta possibility of the formation of ice on the evaporator
be off for maximum cooling.core tins.
