1973 OPEL GT-R instrument cluster

9A-6 1973 OPEL SERVICE MANUAL
b. Remove retaining screw in headlamp lever handle
and remove handle.c. Console cover is held in place by four push button
type studs, unsnap studs by prying cover up and
work cover upwards over shift lever and rubber shift
lever boot.
5. Remove left cover and right plug in instrument
panel cover and through openitigs remove instru-
ment panel attaching screws (points A and B). See
Figures 9A-7 and 9A-8. At this point it will be neces-
sary to lower the steering column, refer to Group 3
for this procedure.6. Remove two multiple wire plug connectors from
steering column harness.
7. Detach speedo cable
8. Remove
dir&ional signal flasher unit. See Figure9A-9.
Figure
9A-9 Directional Flasher Unit
9. Remove 6 instrument cluster retaining screws. See
Figure 9A-10.
Figure
9A-7 Instrument Panel Cover Screw Cover and
Plug LocationsFigure SA-10 Removing Instrument Cluster detaining
SCWWSFigure
SA-8 Location of Hidden Screws10. Grasp instrument cluster and pull straight back,
being careful of wires, etc. See Figure 9A-11.
11. Unscrew heater controls (A) and support bracket
(B). See Figure 9A-12.
12. Disconnect heater and defroster duct
hoses’frominstrument panel. See Figure 9A-13.

HEATER SYSTEM - GT9A. 7
13. Remove all screws from instrument panel pad-
ding and remove it from instrument panel. Arrow in
Figure
9A-14 show location at left side of dash panel
and windshield. Screws are located in same areas on
right side.
Figure 9A-1 1 Removing Instrument Cluster
Figure
9A-14 Instrument Panel Padding Screws
14. Remove one bolt at top of heater blower case and
two nuts from bottom of the case, and remove heater
blower and case assembly. See Figure
9A-15.
Figure 9A-12 Heater Control Screws and SupportBracket
Figure 9A-13 Heater and Defroster Duct Hoses Figure
9A-15
Location of Heater blower Case Boltand Screws
15. On removed heater assembly check relative posi-
tion of mixed air door so that on installation of unit hand control levers can be positioned according to
unit settings, either opened or closed position.

9A-8 1973 OPEL SERVICE MANUAL
Installation
1. Install heater blower and case assembly, securing
with one (1) bolt at the top and two (2) nuts from the
bottom. See Figure
9A-15.
2. Install instrument panel padding and connect
heater and defroster duct hoses, making sure hoses
are properly positioned and connected. See Figure
9A-16.
Figure 9A-16 Heater and Defroster Duct Hoses
3. Install support bracket (B) and heater control (A).
See Figure
9A-12.
4. Carefully push cluster back into instrument panel
housing, making sure electrical wires, etc., are not
pinched.
5. Install six (6) cluster retaining screws. See Figure
9A-10.
6. Install directional signal flasher. See Figure
9A- 9.
7. Attach speedometer cable.
8. Attach two (2) multiple wire plug connectors in
steering column harness.
9. Install steering column. Refer to Group 90.
10. Install instrument panel cover and attach
through openings (points A and B). See Figures
9A-7
and 9A-8.
11. Install right and left opening covers. 12. Install the console shift
cover
between the seats
using the following instructions:
a. Install console cover over shift lever and rubber
shift lever boot.
b. Install cover by pushing down until cover snaps into the four (4) push button type studs.
c. Install two (2) screws under ash tray opening and
install ash tray. 13.
In engine compartment, install hood lock control
cable to lock bar using retaining clip. See Figure
9A-
6.
14. Attach return hoses (B) and coolant feed hoses
(A) to heater core. See Figure
9A-5.
15. Attach lower radiator hose and add collected
coolant.
16. Check for proper operation and leaks in system.
REMOVAL AND INSTALLATION DEFROSTER
OUTLET
Removal
1. Remove instrument panel cover assembly. Refer
to Group 1.
2. Remove screws securing outlet to cover assembly.
Installation1. Install defroster outlet, securing with screws.
2. Install instrument panel cover assembly. Refer to
Group 1.
Figure 9A-17 Heater Valve

RADIO - GT9c. 107mer screw and rotate screw until maximum volume
is achieved.
MAJOR REPAIR
REMOVING AND INSTALLING RADIORemoval
1.
Disc&ect battery.
2. Remove access trim plug from right side of con-
sole. See Figure
9C-1.Figure
9C-3 Location of Access Trim Cover3. Using a 8mm socket, remove hex head screw. See
Figure
9C-2.4. Remove access trim cover on left side of console.
See Figure
9C-3.5. Using a 4mm socket, remove
hex head screw. See
Figure
9C-4.6. Remove tear lock bolts by first,drilling a 3/16 inch
pilot hole and, using a
l/4 inch bolt extractor,
remove bolts. See Figure
9C-5.Figure
9C-5 Drilling Pilot HoleIn\, Tear Lock Bolts7. Disconnect ignition (white) and direction signal
(black) wire set plugs.
8. Support steering column assembly and remove
both hex head bolts.
9. Disconnect speedometer
cabI&10. Remove 6 instrument cluster retaining screws.
See Figure
9C-6.Figure SC-4 Location of Hex Head Screw and Flasher
UnitFigure SC-6 Removing Instrument Cluster Retaining
screws

9C-108 1973 OPEL SERVICE MANUAL
11. Grasp instrument cluster and pull straight back,
being careful of wires, etc. See Figure 9C-7.
Figure 9C-7 Removing Instrument Cluster
12. Disconnect radio harness plug and antenna lead-
in cable from back of radio. See Figure
9C-8.
Figure 9C-8 Removing Radio Harness Plug
13. Remove radio knobs from radio.
14. While supporting radio, remove radio shaft re-
taining nuts. Remove radio. See Figure
9C-10.
CAUTlOk Fasteners in Installation are important at-
taching parts in that they could affect the perform-
ance of vital components and systems, and/or could
result in major repair expense. They must be re-
placed with one of the same part number or with an equivalent part, if replacement becomes necessary.
Do not use a replacement part of lesser quality or
substitute design. Torque values must be used
as
specified during reassembly to assure proper
reten;
tion of these parts.
Figure SC-10 Removing Radio Shaft Retaining Nuts
1. Install radio into instrument cluster and secure
with retaining nuts. See Figure
9C-10.
2. Plug radio harness and lead-in cable into radio.
See Figure
9C-8.
3. Install radio knobs and carefully push cluster back
into instrument panel housing, making sure electri-
cal wires, etc., are not pinched. See Figure
9C-7.
4. Install six (6) cluster retaining screws. See Figure
9C-6.
5. Support column assembly and install ground wire
and hex head bolts, torquing to
14 lb.ft.
6. Install NEW tear bolts and tighten until head of
bolt is twisted off.
7. Connect ignition and directional signal wire plugs.
8. Connect speedometer cable.
9. Install flasher unit and hex head screw. See Figure
9c-4.10. Install hex head screw through opening on right
side and install trim plug. See Figure
9C-2.
11. Install trim cover on left side. See Figure 9C-3.