1973 OPEL 1900 lights

7A- 41973 dPEL SERVICE MANUALConditionPossible CauseCorrectionHeat-blued driven plate
and pressure plate
assembly.
1. Improper pedal1. Replace only driven plate, and
adjustment.adjust clutch pedal and cable.
Grab and chatter with
oil present on clutch
assembly.1. Oil leak.1. Correct oil leakage, clean
pressure plate in solvent, replace
driven plate and adjust pedal lash.
MAINTENANCE AND ADJUSTMENTS
CLUTCH LASH ADJUSTMENT
GTPedal lash, free pedal travel must be adjusted occa-
sionally to compensate for normal wear of the clutch
facings. As the driven plate wears thinner, pedal lash
decreases. Adjust clutch pedal free travel only with
ball stud located on right side of clutch housing if
cable length is not to be changed. To adjust pedal
lash proceed as follows:
1. Loosen lock nut on ball stud end located to the
right of the transmission on the clutch housing. Posi-
tion ball stud so that the outer end protrudes 3/4
inches out of housing and finger tighten lock nut. See
Figures
7A-1 and 7A-6.
2. Adjust ball stud, pivoting clutch release fork, to
obtain 3/4 to
l-1/4 inches pedal lash, free pedal. See
Figure 7A-6.
Opel 1900 and MantaThe clutch actuation works without clutch pedal free
travel. A readjustment of the clutch is only required
if the indicator lamp at the instrument panel lights
up.In synchronism with the gradual wear of the clutch
linings the clutch pedal travels from its basic adjust-
ment position upwards,
ie., towards driver. If the
clutch lining wear has reached such an extent that
the clutch pedal rests against switch, the indicator
lamp at the instrument panel lights up.
This is an indication that the clutch pedal position
has to be corrected to ensure proper clutch operat-
ion.
To
&~sure proper clutch operation, observe the fol-
lowing adjustment instructions.. For all adjustment
dimensions, refer to Figure 7A-7.
1. If the parking brake is provided with an indicator
lamp, the parking brake has to be disengaged, other-wise the same indicator lamp as for the clutch lights
UP.2. Carry out adjustment only with ball stud on clutch
housing whereby the distance (Item 20, Figure 7A-7)
between clutch housing contacting surface and
clutch release lever has to be adjusted in the rear to
4
l/4 inches.
Clutch Control Cable Adjustment(Only on
Installation of a New Clutch Disc or
Bowden
Control Wire)
GT1. Adjust ball stud so that outer end protrudes ap-
proximately 3/4 inches out of clutch housing.
2. Adjust distance between release lever and clutch
housing face at eye for control cable to approxi-
mately 4
l/4 inches. See Figure 7A-6. Hold cable in
this position and place E-ring two grooves ahead of
washer on rubber grommet. Clutch pedal free travel
is now between 3/4 and 1
l/4 inches and clutch
release bearing has proper clearance from pressure
plate.
Opel 1900 and Manta1. Adjust ball stud on clutch housing to basic dimen-
sion of approximately 3/4 inch. With lower end ofbowden control wire unhooked, push clutch release
lever towards the front so that the clutch release
bearing rests against clutch spring. Now, adjust ball
stud so that the dimension (Item 20, Figure
7A-7)between clutch housing contacting surface and
clutch release lever amounts in the rear to 4
l/4
inches.2. Pull reattached bowden control wire out of dash
panel so that clutch pedal rests against switch (in-
dicator lamp lights up).
3. In this position, install lockwasher at upper con-
trol wire attachment three grooves towards the front,
thereby completing control wire adjustment.

7C. 941973 OPEL SERVICE MANUAL
7. Drive out retaining pin and shaft and remove se-
lector detent. See Figure 7C-93.Figure
7C-93Figure
7C-94 - Exploded View of Selector Lever
8. To replace bowden cable in selector lever, knock
off selector handle, remove screws from clamping
piece and pull knob.
9. Remove pull knob and bowden cable, taking care
not to lose lock bolt bushing, thrust springs, ‘and
washer.
10. Place thrust spring, bushing, washer, and thrust
spring onto new bowden cable, in that order, and
insert cable into selector lever.
1 I. Slide pull onto selector lever and clamping piece
onto cable.
12. Heat up new selector lever handle in water to 176
degrees F. and push onto selector lever.
13. Set dimension between pull knob and selector
lever handle at
.4 inch and tighten set screws.
14. Lubricate selector lever detent and shaft. Install
detent, align selector lever with support, install shaft,
and drive in new retaining pin.
15. Install assembly to support housing and install
intermediate selector lever.
16. Install assembly to vehicle and install neutral
start switch.
17. Install console lights and cigar lighter connec-
tions to console and install console to vehicle.
18. Lubricate and connect selector rod to intermedi-
ate selector lever and adjust according to Figure 7C-
198.
MAJOR REPAIRREMOVAL AND INSTALLATION OF AUTOMATIC
TRANSMISSION
Removal
- Opel 1900 and Manta
I. Disconnect battery.
2. Remove dipstick.
3. Remove screws from fan shroud.
4. Remove 2 upper starter bolts.
5. Raise car and provide support for front and rear
and drain oil.
6. Remove bolts from engine support brackets, both
sides. Let brackets hang by front bolts. See Figure7c-105.
7. Remove flywheel cover pan.
8. Remove exhaust pipe from manifold and unhook
rubber tailpipe suspension.
9. Remove drive shaft. Do not misplace thrust spring
in spline.
10. Disconnect cooler lines at flexible hoses.
II. Detach both stabilizer supports from
crossmem-ber to body supports and loosen stabilizer bolts in
lower control arms. See Figure X-84, Callout “B”,

8A-2 1973 OPEL SERVICE MANUAL
HOOD, FENDERS, AND GRILLE
CONTENTS
Subject
DESCRIPTION AND OPERATION:
GTHeadlampOperation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .DIAGNOSIS: (Not Applicable)
MAINTENANCE AND ADJUSTMENTS
GTHeadlampMechanism
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MAJOR REPAIR:
Removal and Installation
Hood (1900
- Manta). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fender(1900-Manta). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Headlamp Covering (1900
- Manta). . . . . . . . . . . . . . . . . . . . . . . .Headlamp Assembly
(GT). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Headlamp
CableAssembly(GT). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Grille
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .SPECIFICATIONS: (Not Applicable)
DESCRIPTION AND OPERATION
DESCRIPTION AND OPERATION OF GT
HEADLAMP MECHANISMThe concealed headlamps are moved mechanically.
Pushing actuating lever on left side of console opens
headlamps, pulling lever closes headlamps. Two
meshing gear segments convert the movement of the
lever to a rotation of 180 degrees. The pivots of the
headlamps lie below the centerline so that with head-
lamps in closed position the headlamp housing is
flush with front sheet metal.
A white indicator lamp in the instrument panel lights
if the headlamps are not completely opened and
locked. The switches of the headlamp electrical sys-
tem are located behind the left headlamp operating
mechanism.
MAINTENANCE AND ADJUSTMENTS
ADJUSTMENT OF HEADLAMP MECHANISMBoth headlamp assemblies must operate in unison in
order to lock in either the open or closed position.
Page No.
8A-2
8A-2
8A-3
8A-3
8A-4
8A-4
8A-6
8A-61. Adjust headlamps to be parallel in any position by
changing length of right headlamp operating rod.
For adjustment loosen clamp bolt (A). See Figure
8A-1.Figure
8A-l Headlamp Operation Adjustments

9C-106 1973 OPEL SERVICE MANUAL
c. Adjust trimmer screw for maximum volume.
d. If antenna trimmer does not have a definite peak, check for defective antenna by substitution.
2. Check that the speaker connection is plugged in
SXUdY.
3. If the radio is still weak, remove the receiver and
speaker assembly for repair.
Radio Is Noisy
1. Radio is noisy all the time:
a. Check for defective antenna by striking antenna
with hand. If static is heard while tapping, replace
antenna.
b. If antenna is not defective, remove receiver and
speaker for repair.
2. Radio is noisy only when jarred:
a. Check antenna as in Step No. 1 above.
b. Check speaker connection. If speaker connection is not at fault, remove receiver and speaker for re-
pair.
3. Radio is noisy when engine is running:
a. Check noise suppressor by substituting on genera-
tor with known good one.
b. Check to see that antenna is mounted securely,
grounding the antenna base to the fender. The an-
tenna lead-in wire is shielded and the shield should
have good ground connection at the receiver and the
antenna base.
c. Check for other car wiring, passing too close to
radio receiver case.
d. If engine noise is still present, remove receiver and
speaker for repair.
4. Radio is noisy when car equipment is operated,
such as directional lights or brake lights:
Check for defective antenna lead-in wire or, loose
antenna mounting, as in Step No. 3b above.
MAINTENANCE AND ADJUSTMENTS
ANTENNA TRIMMER ADJUSTMENT
An antenna trimmer adjusment screw is provided for
matching of the antenna coil in the receiver to the car antenna. This adjustment must always be made after
installation of a receiver or an antenna, or after re-
pair to these units. This adjustment should also be
performed whenever radio reception is unsatisfac-
tory.
1. Position antenna to a height of 31 inches.
2. Tune receiver
tb a weak station at or near 1400
KHz that can barely be heard
with volume turned
fully up.
3. Insert a small-bladed screwdriver in antenna trim-
Figure 9C-1 Location of Access Trim Plug
Figure
9C-2 Removing Hex Head Screw

9C-110 197j 6PEi SERVICE MANUAL
c. Adjust trimmei screw for maximum volume,
d. If antenna trir&ner does not have a definite peak,
check for defective ant&ma by substitution.
2. Check that the speaker connection is plugged in
securely.3. If the radio is still weak, remove the receiver and
speaker assembly for repair.
Radio Is Noisy1. Radio is noisy all the time:
a. Check for defective antenna by striking antenna
with hand. If static is heard while tapping, replace
antenna.
b. If antenna is not defective, remove receiver and
speaker for ripair.
2. Radio is noisy only when jarred:
a. Check antenna as in Step No. 1 above.
b. Check speaker connection. If speaker connection
is not at fault, remove receiver and speaker for re-
pair.
3. Radio is noisy when engine is running:
a. Check noise suppressor by substituting on genera-
tor with known good one.
b. Check to see that antenna is mounted securely,
grounding the antenna base to the fender. The an-
tenna lead-in wire is shielded and the shield should
have good ground corinection at the receiver and the
antenna base.
c. Check for other car wiring passing too close to
radio receiver case.
d. If engine noise is still present, remove receiver and
speaker for repair.
4. Radio is noisy when car equipment is operated,
such as directional lights or brake lights:
Check for defective antenna lead-in wire or loose
antenna mounting, as in Step No. 3b above.
5. Radio is noisy only on dry days when car is mov-
ing:
Wheel and tire static will occur only during dry
weather. To check to see if noise is wheel static or tire
static, drive car until noise is noticed. Touch the
brake. If noise disappears, it is wheel static. If noise
persists, it is tire static. Static may be eliminated in
two ways:a. Wheel static may be eliminated by installation of
static collectors in the front wheels. It is important
to make sure the button on the end of the spiral
collector rides evenly in the spindle. Grease and dirt
can cause poor contact between static collector and
the cap, which would result in wheel static, even with
the collectors installed.
b. Tire static is eliminated by injecting graphite tire
static powder in all
five (5) tires. Either a special gun
or a plastic squeeze bottle can be used to insert pow-
der.MAINTENANCE AND ADJUSTMENTS
ANTENNA TRIMMER ADJUSTMENTAn antenna trimmer adjustment screw is provided
for matching of the antenna coil in the receiver to the
car antenna. This adjustment must always be made
after installation of a receiver or an antenna, or after
repair to these units. This adjustment should also be
performed whenever radio reception is unsatisfac-
tory.1. Position antenna to a height of 31 inches.
2. Tune receiver to a weak station at or near 1400
KHz that can barely be heard with volume turned
fully up.
3. Insert a small-bladed screwdriver in antenna trim-
mer screw and rotate screw until maximum volume
is achieved.
Figure 9C-15 Radio Control Knobs