1973 OPEL 1900 instrument panel

I
,INSTRUMENT PANELlH-63Figure l;H-15 Removing Instrument Cluster AssemblyFibure1 H-l 6 Disconnecting Radio Wires
14. Disdonnect antenna lead-in at right lower corner
of radio!
15. Pull’ cluster housing out and turn sideways to
remove
&~y instrument gauge or switches.
I
lnstallaiion
CAUTlOI$ Fasteners in subparagraph B are impor-
tant attaching parts in that they coo/d
affect the
perform>nce of vital components and systems, and-
/or
cou!d result in major repair expense.They must
be
repraced with one of the same part number, or
with an equivalent part if replacement becomes
necessa?y. Do not use a replacement part of lesser
quality
br substitute design. Torque values must be
used as
&ified during reassembly to assure proper
retention of these parts.
1. Plug antenna lead-in cable and power source to
radio. I
2. Put i&trument cluster in position and replace six
(6) screbs in cluster.3. Connect speedometer cable.
4. Raise steering column into position and install hex
head
bolt% Be sure to install ground wire. Tighten
hex head bolts to 14 lb.ft.
5. Tighten tear lock bolts until hex head of bolt is
torn off.
6. Connect ignition and directional signal wire set
plugs.
7. Install flasher unit.
8. Replace screws in right and left lower instrument
panel and replace both access covers.
9. Connect battery cable.
Removal of Combined Switch Assemblies. GT1. Remove instrument cluster.
2. Turn instrument cluster to the side to remove
switch assembly.
3. Remove switch by removing two retaining nuts.
See Figure lH-17.
4. Remove wiring from switch.
Figure 1 H-l 7 Removing Switches
Installation1. Plug wiring into switch.
2. Install switch on panel.
3. Install instrument cluster.

I
IGAUGES1 I- 69
I
I
3. Replace instrument housing.InstallationFiemoving~Temperature Indicator or Fuel Gauge
1. Remov+ instrument cluster housing.
2. Remov; six screws and remove both instrument
cluster
le+ See Figure 11-2.3. Pull v&age stabilizer off printed circuit and
remove fohr instrument attaching screws, as shown
in Figure
111-5.Figure
11-5 Removing Four Instrument Attaching\SCWWS
4. Take temperature or fuel gauge out of clusterlnstallatidn
1. Install itemperature or fuel gauge in cluster.
2. Replack voltage stabilizer on back of printed cir-
cuit. I
3. Replack both instrument cluster lens.
I
4. Install /instrument cluster housing.
I
IRemwind Rallye Gauges
1. Removt glove compartment.
2. Remo?e radio, if equipped.
3.
Remoje screws holding instrument carrier frominstrumejf
pane!.4. Disconpect wres from instrument gauge.
5.
Removal attaching nuts from gauge and remove.I1. Replace gauge with attaching nuts on panel.
2. Hook up wires to gauges.
3. With holding screws, attach gauge cluster to in-
strument panel.
4. Replace radio.
5. Replace glove compartment.
Removal of Temperature Sending Unit
1. Drain and collect coolant.
To drain radiator, remove end of lower radiator hose
that is connected to radiator.
2. Remove wire from temperature sending unit.
3. Unscrew temperature sending unit from thermo-
stat housing. See Figure
11-6.Figure
11-S -Temperature Sending Unitlnstalletian
1. Screw temperature sending unit into thermostat
housing after sealing unit with non-hardening per-matex.
2. Install wire on sending unit.
3. Replace coolant.

1 J- 72 1973 OPEL SERVICE MANUAL
I
WIRING IDIAGRAMS
CONTENTS
Subject
1973 WIRING DIAGRAMS: Windshield Wiper and
Horn:- Opel 1900 -
Manta....................................I.............. ..............................
Windshield Wiper and Horn’- Rallye ..........................
Windshield Wiper
andHorn!-GT
..................................
Turn Signal and Hazard Flasher
-
Opel 1900 - Manta !
........................................................
Turn Signal and Hazard Flasher
- GT ..........................
Oil, Fuel,
Temp.: Tach, Stop and Brake
Warning Light
.GT........................................................
Blower Motor, Lighter and
Rackup Lights -
Qpel 1900.Manta ........................................................
Blower Motor and Lighter
.,GT....................................
Indicator Lights and Gauges
- Opel 1900 -
Manta ........................................................................\
........
Indicator Lights
andGauges.Rallye ..........................
Dome Light and Buzzer
- Opel 1900 - Manta..........
Dome Light, Buzzer and Clock - GT ............................
Headlamps
- Opel 1900 ’
....................................................
Headlamps
.Mantaj............................................................
Headlamps and Fog Lights
.Rallye ..............................
Headlamps, Parking, Tail and Instrument
PanelLighting.GT ........................................................
Left Parking and Tail Lights
- Opel 1900 -
Manta ..................................i.............................................
Right Parking and Tail Lights
- Opel 1900 -
Manta................. ..*............................................................
Starting, Ignition and Charging
-
Opel 1900.Manta..........i.............................................
Starting, Ignition and Charging
- GT ..........................
Instrument
Panel.GT ......................................................
A/C Generatorand Regulator
- All Models..............
Seat Belt Warning System (Manual Transmission)
-Opel1909-Manta ..........................
Seat Belt Warning System (Automatic Transmission)
.Opel 1900 - Manta..........................
Seat Belt Warning System (Manual Transmission)
- GT........................................................ Page No.
1 J-74
1 J-75
1 J-76
1 J-77
1 J-78
1 J-79
1 J-80
lJ-81
1 J-82
1 J-83
1 J-84
1 J-85
1 J-86
1 J-87
1 J-88
1 J-89
1 J-90
1 J-91
1 J-92
1 J-93
1 J-94
1 J-95
1 J-96
1 J-97
1 J-98

WIRING DIAGRAMSlJ- 91
RFigure
lJ-18 Right Parking, Tail and Instrument Panel Lighting -Opel 1900. Manta

1 J- 94 1973 OPEL SERVICE MANUALi
I
IFigure lJ-21 Instrument Panel GT

26-341973 OPEL SERVICE MANUAL
a 13/16 inch deep socket, and remove. See Figure2G-6.Figure
ZG-4 Seat to Underbody Hook
Figure
ZG-5 Seat Back Metal Tabs
3. Remove seat back towards the top.
REMOVAL AND INSTALLATION
OF GLOVE
COMPARTMENT DOOR LOCK
1. Unscrew nut of glove compartment lid lock, usingFigure ZG-6 Removing Glove Compartment Lock
2. Install new glove compartment lid lock.
REMOVAL AND INSTALLATION OF FRONT SIDE
PANEL TRIM PAD
1, Lift up door sill shield and pull off sealing strip up
to the instrument panel cover. See Figure 2G- 7.
Figure
ZG-7 Pulling Off Sealing Strip

OPEL 1900 AND MANTA STEERING COLUMN ASSEMBLY 3E.35
II
OPEL 1900 AND MANTA STEERING COLUMN
ASSEMBLY
CONTENTS
SubjectPage No.
DESCRIPTION AND OPERATION:
Description and Operation of Directional Signal
Lever. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Description
andOperationofHorn. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Description of Steering Column Assembly
. . . . . . . . . . . . . .DIAGNOSIS: (Not Applicable)
MAINTENANCE AND ADJUSTMENTS: (Not
Applicable)
MAJOR REPAIR:
3E-353E-363E-36
Removal and Installation of Steering Column
Assembly
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RemovalandInstallationofSteeringWheel. . . . . . . . . . . .Disassembly and Reassembly of Direction Signal
Switch
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Disassembly and Reassembly of Steering and
Ignition Lock Cylinder, and Electrical Switch
from Mast Jacket Assembly
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .SPECIFICATIONS:
Steering
ColumnSpecifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3E-363E-383E-393E-403E-41
DESCRIPTION AND OPERATIONDESCRIPTION AND OPERATION OF
DIRECTIONAL SIGNAL LEVERhigh to low beam or vice versa. On all
19M) Rallye
cars, when switching from low to high beam posi-
tion, with the fog lamp instrument panel switch ON
The direction signal switch lever is a multi- purpose
lever controlling direction signals, passing signal and
headlight high and low beams. See Figure
3E-2.The dire&M signal lever is provided with a two-
step mechanism for operation of headlight high and
low beams, and passing signal (not in N.J.). With
headlights off, moving the lever repeatedly towards
steering wheel flashes headlights as a passing signal.
With headlights on, moving the lever repeatedly to-
wards steering wheel up to first stop also flashes
passing signal regardless whether or not the direction
signals are switched on. When the lever is moved up
to the second stop, the headlights are changed from
SE.2Figure
3E-2 Directional Signal Lever Position for
Headlamp Operation

3E- 38 ,1973 OPEL SERVICE MANUAL
ponents and systems, and/or could result in major
repair expense. They must be replaced with one or
the same part number or with
an equivalent part if
replacement becomes necessary. Do not use a
re-
placement part of lesser quality or substitute design.
Torque
values must be used as specified during reas-
sembly to assure proper retention of these parts.On installation, make sure steering wheel spokes
point downwards and steering gear is in high point.
1. Carefully insert steering mast into universal joint
flange.
2. Loosely attach slide-off base attaching nuts at un-
derside of instrument panel.
3. Attach steering mast jacket at front of dash, using
a notched hex nut.
4. Torque nuts at slide-off base to II
lb.ft.5. Tighten screw at steering mast clamp to 22
lb.ft.6. Reconnect wires to directional signal switch and
ignition switch.
7. Reconnect battery.
REMOVAL AND INSTALLATION OF
STEERING WHEELThis procedure may be performed with the steering
column assembly either removed or installed in the
car.
Removal
1. Disconnect battery.
2. Pry off horn cap and remove wires from cap. See
Figure
3E-3.3. Bend lockplate tabs down and take off steering
shaft nut and lockplate.
4. Install steering wheel remover J-21686 as shown
in Figure
3E-9 and pull off steering wheel.
Installation1. Before installing steering wheel, lubricate return
pin and sliding area on directional signal switch re-
turn cams and horn contact ring.
2. Make sure that clamp bolt in steering shaft flange
is on top.
3. Make sure notch on steering shaft face is in hori-
zontal position.Figure
3E-9 Removing Steering Wheel
4. With the steering wheel centered, place the steer-
ing wheel onto the steering shaft.
5. Install steering wheel lockplate and nut. Torque to
11
lb.ft.
CAUTION:
This steering wheeI to steering shaft fas-
tener is an important attaching part in that it could
affect the
performance of vital components and sys-
tems, and/or could result in major repair expense. It
must be repked
with one of the same part number
or with an equivalent part if replacement becomes
necessary. Do not use a replacement part of lesser
quality or substitute design. Torque
values must be
used as specified during reassembly to assure proper
retention of this part.6. Bend lockplate tabs up, connect horn cap wires
and replace cable and cap.
7. Reconnect battery.
REMOVAL AND REPLACEMENT OF HORN
CONTACT RING
1. Remove steering wheel.
2. Cut off defective contact ring at wire.
3. Strip wire approximately
l/8”.4. Install new part and solder connection with resin
core solder.
5. Lubricate contact ring with lubriplate, or equiva-
lent.
6. Reinstall steering wheel.