1970 FIAT 500 bulb

FIG 11:18 Replacement of bulb from inside f r o n tcompartment
Key to Fig 11 :18 1 Double-filament bulb 2 Bulbholder
3 Side direction indicator light 4 Bulbholder shield
PARKING LAMP
LENS
SIDE DIRECTIONINDICATOR
FIG 11 :19 Disassembling front parking and direction
indicator lamp
Replacement of the bulb is achieved from inside the front
compartment by pulling down the upper lug of the
rubber protection cap at the rear of t h e headlight unit and
freeing the bulb holder. Pull up the bulb holder to
reflector fastener spring and pull out the bulb holder
complete and replace the bulb as necessary.
Beam setting:
Accurate setting is best left to a service station
equipped with the necessary equipment. The main beams
must be set parallel to the road surface or in accordance
with local regulations. Adjustment is made by turning
the top screw 1 as indicated in FIG 11:17 for the
vertical setting and the lower screw 2 for the horizontal
setting.
122
FIG 11 : 20 Disassembling tail parking, stop, direction
indicator lamp and reflector lens REFLECTOR LENS PARKING A N D
STOP LAMP INDICATOR LAMP
DIRECTION
LENSLENS
SCREWS
Lamps light when switched on but gradually fade:
Check the battery as it is incapable of supplying
current for any length of time. Front parking and direction indicator lamp:
To replace the double filament bulb, release the screws
securing the lens to the lamp casing as shown in FIG
11 :19 and remove the bulb from its bayonet holder. Where
the parking lamp is in the headlamp unit the bulbholder
can be pulled out inside the front compartment.
Rear parking, direction indicator, stop lamps and
reflector lens:
To renew any of the t w o bulbs remove the t w o screws
securing the lens to the lamp casing as shown in FIG
11 : 2 0. Bulbs are fixed by bayonet couplings.
Side direction indicator lamps:
To replace the 2.5W bulb slide off the bulb holder
from the rubber socket located as shown in FIG 11 :19.
The bulb is secured by a bayonet coupling.
Number plate lamp:
To replace the bayonet coupled 5W bulb remove the
lens and light cap mounting screws as shown in FIG
11:21.
Lamps give insufficient light:
Test the state of charge of the battery and recharge if it
is necessary from an independent supply. Check the
setting of the lamps. If the bulbs have darkened through
age fit new ones.
Lamps burn out frequently:
If this is accompanied by a need for frequent topping-
up of the battery and high hydrometer readings, check
the charging rate with an ammeter when the car is
running. This should be around 3 to 4 amps. A reading in
excess of this calls for adjustment of the regulator.

Lamp brilliance varies w i t h the speed of t h e car:
Check the condition of the battery. Examine the battery
connections. Make sure they are tight and renew faulty
cables.
11:10 Panel and warning lights:
All the gauges are clustered in a single instrument
mounted on the dashboard above the steering column.
Incorporated in this cluster is the parking light pilot light,
generator charge indicator, fuel reserve supply indicator,
low oil pressure indicator, and the speedometer w i t h
mileage recorder.
The parking lamp indicator glows green when the
ignition lock switch key is in either position 1 or 2 once
the toggle switch on the instrument panel has been
operated.
The generator charge indicator shows red only when
the ignition is turned on. It should be extinguished when
the generator output is sufficient for battery charge
(12.6 ± 0.2 volts) with the engine running at a speed
of 1100 rev/min and the headlights switched off.
The fuel reserve supply indicator shows red only when
the ignition is turned on and the amount of fuel in the
petrol tank has dropped to approximately .8 to 1.1
Imp. gallons.
The low oil pressure indicator shows red only when the
ignition is turned on and should be extinguished when
the oil pressure reaches 7.1 to 21.3 Ib/sq in, and opens
the sending unit contacts. Once the engine is at normal
operating temperature but at a speed below 1000 rev/
min the indicator might light up even the pressure is under
control and with normal operation.
All the bulbs fitted to the above described units are of
the tubular 2.5W type and to renew a bulb extract the
bulb holder from the rear of t h e instrument cluster and
release the bulb which is attached by a normal bayonet
coupling.
Fuel reserve supply indicator sender u n i t:
The fuel reserve supply indicator should be checked for
correct indication by allowing the fuel tank to empty and
then inserting .8 to 1.1 Imp. gallons at which stage the
light should extinguish. Any failure to do so should be
checked as follows:
1 Ensure that the indicator bulb operates correctly.
2 Check for complete circuit between the sender unit and
the indicator bulb.
3 If the sender unit float bracket is distorted the bulb
will
indicate a reserve supply of fuel greater or smaller than
specified. The bracket should be adjusted to give
correct indication of fuel level.
4 The sender unit could have been inadvertantly
damaged in which case the unit must be renewed.
11 :11 The horn
The horn circuit comprises the horn, push button at the
centre of the steering wheel and normal earth return
electrical circuit through the car body. One terminal is
connected to the battery whilst the other to the push
button on the steering wheel which when the button is
depressed the circuit will be closed so causing the horn
to operate.
F500
FIG 11 : 21 Number plate lamp
Key to Fig 11 : 21 A Lens and light cap mounting screws
B Lens
FIG 11 : 22 Horn (opened)
Key to Fig 11:22 1 Body 2 Diaphragm 3 Armature
4,5,6 Core 7 Cable: terminal-condenser-stationary contact
8 Cable: terminal-magnetizing coil end 9 Magnetizing coil
FIG 11 :23 Horn sound adjustment. Obtained by adjust-
ing the armature air gap
123

(h) Starter motor rough or noisy
1 Mounting bolts loose
2 Damaged pinion or flywheel gear teeth
( i ) Lamps inoperative or erratic
1 Battery low, bulbs burned out
2 Faulty earthing of lamps or battery
3 Lighting switch faulty, loose or broken wiring
connections
F500
125
(j) Wiper motor sluggish, taking high current
1 Faulty armature
2 Bearings out of alignment
3 Commutator dirty or short-circuited
(k) Wiper motor operates but does not drive
arms
1 Gearbox components worn

8 Refit the intermediate protection lining ensuring that
it is properly located and well glued. Refit the door
lining panel, key and crank handle.
Door ventilator:
The door ventilator comprises the glass, weather strip
placed between the glass and chromium plated frame,
the chromium plated frame together with pin and bracket
for upper and lower hinging, frame control handle and
lining.
To remove the ventilator glass first drill the upper pivot
pin using a portable electric drill and release the nut and
locknut from the lower pivot bracket. Carefully lift away
the glass.
Reassembly:
To reassemble the ventilator glass proceed as follows:
1 Coat the outer edge of the glass on which the chrome
plated frame must be installed with a 50% solution of
petrol and oil to ensure that the glass can be easily
inserted into the frame.
2 Install the lock handle which is secured to the frame
by means of a screw sunk into the handle body and
t w o corrugated spring washers placed between the
frame and the handle.
3 Before installing the ventilator pane on the door panel
ensure that the metal channels in the front post flanges
at the pane base are firmly located in place and f i t the
rubber weather strip arranging it carefully in its
seating. The weather strip is secured by clips located
on the metal channels.
4 Refit the handle striker plate and secure it to the door
channel by means of t w o self-tapping screws.
5 Insert the lower ventilator swivel on the door panel to
welded bracket. Fit the spring and secure ventilator
assembly through the nut, locknut and plain washer so
that it can, be freely adjusted to any position without
undue effort (see FIG 12:5).
6 Fit the chrome cover on the lower ventilator swivel.
Refit the upper ventilator swivel in the door panel
brackets and clench it using a hammer and a suitably
sized drift against a firm metal block. This will ensure
correct ventilator movement.
FIG 12:8 Adapting windshield weatherstrip. Simply
pull the draw-cord
F500
131 RUBBER BUFFER-HOOD LID LINING
BUMPER
FIG 12:9 Front compartment lid lining and rubber
buffers
HOOD STAY SPRING HOOD STAY HOOD HINGE LOCKING NUTS-
FIG 12:10 Close-up view of hood lid hinge and stay
1 2 : 6 Removing windshield glass
Removal:
To remove the windshield glass carefully push from the
interior of the car against the glass and with the assistance
of a second operator carefully ease the glass away f r o m
the glass aperture as shown in FIG 12:6.
Refitting :
1 Fit the weather strip onto the glass.
2 Insert a draw cord completely around the weather strip
outer lip. Ensure t h a t the cord ends come to the centre
of the lower edge of the glass.
3 Press t h e windshield assembly against the body
opening from the outside as shown in FIG 1 2 : 7 and
then carefully pull the cord ends from the inside so the
overlap of the weatherstrip will locate over the body
opening lip (see FIG 12 : 8).
4 Carefully replace the rear view mirror bulb cable
between the weather strip lip and the body panel from