1969 FORD MUSTANG lock

[x] Cancel search: lock

infotainment wheel bolts fuel cap load capacity hood open dashboard

Load previous 8 pages

Page 51 of 413

FORD MUSTANG 1969 Volume One Chassis
BOLT

2-REQUIRED
PARKING BRAKE

CONTROL ASSEMBLY

2780
2.00 ARMOR
I
A RKING
RRAKE

HONT CABLE-2853

ADJUSTING NUT

EQUALIZER-2A602

2628

CLIP

VIEWY 2A814 ASSEMBLY

BOLT-2 REQUIRED 2A706

2853

Page 52 of 413

FORD MUSTANG 1969 Volume One Chassis
PARKING BRAKE CONTROL

TO-ACTUATOR CABLE AND

CONDUIT ASSEMBLY-2853
PARKING BRAKE CABLE ASSEMBLY-2A635 R.H.

2A635 PARKING BRAKE CABLE

ASSEMBLY R.H. TO BE POSITIONED

WITH RUBBER LOCATERS CENTERED

Page 54 of 413

FORD MUSTANG 1969 Volume One Chassis
02-02-35
Brake System

02-02-35

4.
Attach a wire to the end of the

cable to assist in routing new cable.

5.
Lower the vehicle.

6. Remove the parking brake front

cable ball retaining clip from

02-02-35
Brake System

02-02-35

4.
Attach a wire to the end of the

cable to assist in routing new cable.

5.
Lower the vehicle.

6. Remove the parking brake front

cable ball retaining clip from the

clevis.

7.
Disconnect the cable ball from

the notch in the brake clevis.

8.. Remove the hairpin retainer and

remove the cable assembly from the

brake control assembly.

9. Pull the cable assembly up through

the opening in the floor and remove

the wire from the end of the cable.

Installation

Refer to Fig. 36.

1.
Connect the wire to the end of

the cable assembly and pull the cable

down through the opening in the

floor. Remove the wire.

2.
Connect the cable assembly to

the brake control assembly and in-

stall the hairpin retainer.

3.
Position the ball end of the

cable in the notch of the brake clevis.

4.
Raise the vehicle on a hoist.

5.
Pull the cable grommet into po-

sition and route the cable through

the access holes in the side rail and

under the fuel line.

6. Insert the cable into the body

bracket and install the hairpin re-

tainer.

7.
Position the spring, spring seat,

and equalizer on the cable and install

the two nuts.

8. Adjust the parking brake.

LINCOLN CONTINENTAL

Removal

1.
Raise the car on a hoist. Dis-

connect the parking brake cable from

the equalizer lever underneath the

car (Fig. 38).

2.
Remove the retaining clip at the

cable bracket, and disengage the cable

from the bracket (Fig. 38).

3.
Remove the supporting clip re-

taining bolts and remove the support

plate from the underbody.

4.
Lower the car on a hoist.

5.
With the parking brake in the

fully released position, disconnect the

cable at the control assembly.

6. Raise the vehicle on a hoist. Re-

move the left front fender apron

splash shield retaining bolts and the

splash shield.

7.
Remove the two bolts securing

the parking brake control to equaliz-

er cable bracket to the dash panel

and remove the cable from the vehicle.
Installation

1.
Route the parking brake control

to equalizer cable to the control as-

sembly and the equalizer, and install

the two bolts that retain the cable

to the dash panel (Fig. 38).

2.
Install the left fror%/ender apron

splash shield and the ^u attaching

bolts.

3.
Lower the vehicle.

4.
Connect the control cable to the

clevis on the control assembly.

5.
Raise the car on a hoist.

6. Position the supporting clip and

cable on the vehicle and install the

retaining bolts. Do not tighten the

bolts.
Position the cable armor ap-

proximately 1/2 inch to the right of

the clip (looking toward the rear of

the car) and tighten the retaining

bolts.

7.
Position the equalizer control

cable to the support bracket and in-

stall the retaining hairpin clip.

8. Connect the ball end of the con-

trol cable to the equalizer lever.

9. Adjust the parking brake linkage

(Part
2-1,
Section 2).

10.
Check the operation of the auto-

matic release mechanism.

PARKING BRAKE

ACTUATOR-TO-EQUALIZER

CABLE

FORD, MERCURY,

METEOR, THUNDERBIRD

AND CONTINENTAL

MARK III

Removal

Refer to Figs. 34 and 37.

1.
Raise the vehicle on a hoist.

2.
Remove the lock and adjusting

nut which retains the cable to the

equalizer.

3.
Remove the cable end from the

equalizer.

4.
Unhook the cable from the act-

uator, and remove from the vehicle. *

Installation

1.
Insert new cable end into act-

uator.

2.
Insert cable end into equalizer

and tighten the adjusting nut snug.

Install the lock nut.

3.
Adjust the parking brake cable

tension and check operation as out-

lined in Part
2-1,
Section 2.

4.
Lower the vehicle.
PARKING BRAKE EQUALIZER

TO REAR WHEEL CABLE

FORD, MERCURY,

METEOR, THUNDERBIRD

AND CONTINENTAL

MARK III

Removal

1.
Raise the vehicle and tffosen the

parking brake equalizer rod" adjusting

nut. Disconnect the equalizer from the

rear cables (Figs. 34 and 37).

2.
Compress the prongs on the left

cable-to-frame side member retainer

so the prong can pass through the

side-member. Remove the clip that at-

taches the left cable to the left lower

arm. Pull the cable thru the frame left

side member.

3.
Compress the prongs on the

right cable-to-frame side member re-

tainer bracket so the prong can pass

through the bracket. Remove the clips

retaining the right cable to the frame

crossmember.

4.
Remove the rear wheel cover and

wheel. Remove the three Tinnerman

nuts that hold the brake drum in place

and remove the drum.

5.
Working on the wheel side of the

rear brake, remove the automatic

brake adjuster spring. Compress the

prongs on the parking brake cable re-

tainer so that they can pass through

the hole in the brake backing plate.

Draw the cable retainer through the

hole.

6. With the spring tension off the

parking brake lever, lift the cable out

of the slot in the lever and remove the

cable through the backing plate hole.

Installation

1.
Pull enough of the parking brake

cable through the housing so that the

end of the cable may be inserted over

the slot in the parking brake lever on

the rear brake shoe.

2.
Pull the excess slack from the

cable, and insert the cable housing

into the brake backing plate access

hole so that the retainer prongs ex-

pand. The prongs must be securely

locked in place. Install the automatic

brake adjuster spring.

3.
Position the right hand cable and

the two retaining clips and screws on

the rear crossmember. Compress the

prongs on the right cable and position

the cable in the retaining bracket on

the frame side member. Be sure theprocarmanuals.com

Page 55 of 413

FORD MUSTANG 1969 Volume One Chassis
02-02-36
Brake System

02-02-36

locating stripe on the cable is midway

between the retaining clips and tighten

all retaining clip screws.

4.
Position the left cable, retaining

clip and screw o

02-02-36
Brake System

02-02-36

locating stripe on the cable is midway

between the retaining clips and tighten

all retaining clip screws.

4.
Position the left cable, retaining

clip and screw on the left lower sus-

pension arm. Compress the prongs on

the left cable and position the cable

through the frame side-member. The

prongs must be securely locked in

place.

5.
Insert the ball ends of the cables

into the equalizer assembly.

6. Install the rear drum(s) and

tighten the three Tinnerman nuts and

secure the drum. Install the wheel and

tire and the wheel cover.

7.
Adjust the parking brake linkage

as outlined in Part 2-1, Section 2. Ad-

just the rear brakes, as required (Part

2-1,
Section 2).

FAIRLANE, MONTEGO,

MUSTANG AND COUGAR—

EXCEPT STATION WAGON

Removal

1.
Remove the equalizer lock nut

and adjusting nut, equalizer, spring

and spring seat.

2.
With the cables slack, discon-

nect the ball-ends from the connector

(Figs.
35 and 36).

3.
Remove the cable from the re-

tainer hooks (station wagon models)

and the underbody guide (convertible

models) if required.

4.
Remove the hairpin lock retain-

ing the cable housing to the side rail

bracket.

5.
Remove the wheel cover, wheel

and tire and the rear brake drum as

outlined in Section 2.

6. Remove self-adjuster springs to

allow clearance to remove cable re-

tainer from the backing plate. Discon-

nect the rear end of the cable from the

parking brake lever on the brake shoe.

Disengage the cable housing retaining

grommet or steel-pronged Hi-Hat

from the backing plate and withdraw

the cable and housing from the in-

board side of the backing plate.

7.
Slide the cable and housing out

of the side rail bracket.

Installation

1.
Insert the rear end of the cable

through the side rail bracket and pull

the cable and housing into position.

2.
Insert the rear end of the cable

and housing through the hole in the

backing plate from the inboard side.

3.
Connect the cable to the parking
brake lever on the brake shoe and in-

stall the cable housing retaining grom-

met or steel-pronged Hi-Hat in the

backing plate.

4.
Install the self-adjuster springs.

Position the cable housing in the side

rail bracket and install the hairpin

type retainer.

5.
Install rear hub and drum as-

sembly, wheel and tire assemblies and

wheel cover as outlined in Section 2.

6. Position the cable retainer hooks

(station wagon models) in the under-

body guide (convertible models) and

install the connector, thus hooking the

two cables together.

7.
Insert the cable into the equaliz-

er and install the equalizer, spring

seat, spring, adjusting nut and lock

nut to the front, parking brake control

cable.

8. Adjust the parking brake^as di-

rected in Part 2-1, Section 2.

FAIRLANE AND MONTEGO

STATION WAGONS AND

FALCON PASSENGER

MODELS

Removal and Installation

Refer to Fig. 35.

Generally follow the procedure

given above, omitting separation of

the cables, since the parking brake

rear cable assemblies supplied for

these models is in one piece. Removal

and installation of both rear wheels,

tires and drums will also be required.

LINCOLN CONTINENTAL

Removal

1.
Raise the car. Remove the rear

wheel cover. Remove the wheel and

tire as an assembly.

2.
Remove the three Tinnerman

nuts that hold the brake drum in

place, and remove the drum.

3.
Remove the brake shoe retract-

ing springs.

4.
Loosen the equalizer rod adjust-

ing nut and disconnect the cable from

the equalizer (Fig. 38).

5.
Remove the hairpin-type retainer

clip that secures the cable housing to

the body bracket, and pull the cable

and housing out of the bracket (Fig.

38).

6. Remove the cable to underbody

clamp attaching nuts and the clamp.

Disengage the cable housing from the

hook-type retainer at the spring U-

bolt.
7.
Working on the wheel side of the

backing plate (Fig. 38), compress the

prongs on the cable retainer so that it

can pass through the hole in the back-

ing plate. Draw the cable retainer out

of the hole.

8. With the spring tension off the

parking brake lever, lift the cable out

of the slot in the lever and remove it

through the backing plate hols.

Installation

1.
Pull enough of the cable through

the cable housing so that the end of

the cable may be inserted through the

backing plate hole from the inner side

and engage the cable end with the slot

in the parking brake lever.

2.
Pull the excess slack from the

cable and insert the cable housing into

the backing plate access hole (Fig.

38).
The prongs must be securely

locked in place.

3.
Install the brake shoe retracting

springs.

4.
Position the cable to the under-

body and install the retaining clamp

so that the cable conduit armor ex-

tends forward of the clamp as shown

in Fig. 38. Install the clamp retaining

nuts.

5.
Hook the cable housing to the

retainer at the spring U-bolt.

6. Engage the forward end of the

cable housing with the frame bracket

and secure it with the hairpin-type

clip.

7.
Insert the ball end of the cable

into the equalizer.

8. Make a preliminary brake ad-

justment with the use of Tool HRA-

8650 (Fig. 11).

9. Install the rear drum. Tighten

the three Tinnerman nuts that secure

the drum. Install the wheel and wheel

cover.

10.
Adjust the parking brake link-

age.

11.
Lower the vehicle.

ANTI-SKID CONTROL

ACTUATOR

REMOVAL

Refer to Fig. 39.

1.
Working in the passenger com-

partment, under the glove box, remove

the screw that attaches the forward

end of the control module retainer to

the support assembly. Lower the for-

ward end of the control module re-

tainer and remove the module assem-

bly.procarmanuals.com

Page 57 of 413

FORD MUSTANG 1969 Volume One Chassis
02-02-38
Brake System

02-02-38

2.
Disconnect the actuator solenoid

and warning switch harness connectors

from the control module.

3.
Remove the two wiring harness

grommets from the dash pane

02-02-38
Brake System

02-02-38

2.
Disconnect the actuator solenoid

and warning switch harness connectors

from the control module.

3.
Remove the two wiring harness

grommets from the dash panel and

push the wiring harness and connec-

tors through the openings in the dash

panel.

4.
Working in the engine compart-

ment loosen the hose clamp and re-

move the air hose from the air filter.

5.
Remove the engine air cleaner-

Loosen the hose clamp and remove

the vacuum hose from the vacuum

manifold fitting.

6. Raise the vehicle on a hoist.

7.
Disconnect the exhaust pipes

from the exhaust manifold and sup-

port with wire to provide access to the

actuator assembly.

8. Remove the bolt retaining the

actuator ground wire to the rear outer

corner of the engine right bank.

9. Loosen the tube nuts and discon-

nect the brake system hydraulic tubes

from the hydraulic valve housing.

10.
Remove the three nuts retaining

the actuator assembly to the actuator

support bracket.

11.
Remove the three bolts that re-

tain the actuator mounting bracket to

the side rail and remove the mounting

bracket.

12.
Remove the actuator assembly

from the vehicle and place it on a

bench.

13.
Remove the air and vacuum

hoses from the actuator.

INSTALLATION

1.
Install the air and vacuum hoses

on the new actuator.

2.
Place the actuator assembly into

position under the vehicle, routing the

air and vacuum hoses up between the

engine and fender apron and inserting

the solenoid leads through the holes in

the firewall.

3.
Position the ground wire to the

rear of the engine block and install re-

taining bolt.

4.
Position the actuator mounting

bracket to the frame side rail and in-

stall the three retaining bolts.

5.
Position the actuator assembly

to the mounting bracket and install

the three retaining nuts.

6. Connect the hydraulic tubes to

the hydraulic valve assembly and

tighten the tube nuts to specifications.

7.
Connect the exhaust pipes to the

exhaust manifolds.

8. Lower the vehicle.

9. Pull the actuator solenoid and

brake warning switch wiring harness
through the two holes in the dash

panel from inside the car. Seat the

wiring harness grommets in the dash

panel.

10.
Connect the actuator solenoid

and brake warning switch wiring har-

ness connectors to the control mo-

dules.
'

11.
Position the control module in

the bracket under the glove box and

install the retaining screw.

12.
In the engine compartment con-

nect the air hose to the air filter and

position the hose clamp.

13.
Connect the vacuum hose to the

engine vacuum manifold fitting. In-

stall the engine air cleaner.

14.
Bleed the rear brake system and

centralize the pressure differential

valve.

15.
Raise the rear wheels. Apply

the brakes with the rear wheels turn-

ing to verify proper operation of the

anti-skid control system.

ANTI-SKID CONTROL MODULE

REMOVAL

Refer to Fig. 39.

1.
Remove the retaining strap hold-

ing the harnesses.

2.
Remove the screw that attaches

the forward end of the control module

retainer to the support assembly.

3.
Lower the forward end of the

control module and retainer from the

support assembly; move the module

and retainer forward slightly until the

flange clears the slot in the support

assembly.

4.
Disconnect the five wiring har-

ness plugs from the control module.

5.
Remove the control module from

the vehicle.

INSTALLATION

1.
Connect the five wiring harness

plugs to the control module. Only one

arrangement is possible.

2.
Position the control module in

the retainer, orienting the module per

the markings on it, and insert the re-

tainer flange into the slot at the rear

of the support assembly.

3.
Pivot the retainer and control

module upward and align the screw

hole in the forward end of the retainer

with the hole in the support bracket

assembly. Install the retaining screw.

4.
Test the vehicle on the hoist to

verify correct operation of the skid

control system.
5.-
Secure the wiring to the module

support extension with the retaining

strap.

ANTI-SKID CONTROL SENSOR

REMOVAL

Refer to Fig. 39.

1.
Raise the vehicle on a hoist.

2.
Remove the rear wheel and tire

assembly.

3.
Remove the three Tinnerman

nuts (3) and remove the brake drum.

4.
Disconnect the sensor lead from

the rear wiring harness.

5.
Unseat the sensor lead grommet

pushing it to the inside of the brake

assembly.

6. Remove the four nuts that retain

the sensor to the backing plate and

pull the axle shaft, sensor assembly

and wheel bearing assembly from the

axle housing.

7.
Press the wheel bearing retainer

and wheel bearing off the axle shaft

(Refer to Part 4-2).

8. Remove the sensor assembly and

press the rotor off the shaft with tool

T69P-2B384-A Detail 2 and TOOL

1225-DA.

INSTALLATION

1.
Press a new rotor onto the axle

shaft. Install a new sensor assembly

on the shaft with tool T69P-

2B384-ADetail 1 and TOOL 1225-

DA, and press the bearing and bear-

ing retainer onto the shaft (Refer to

Part 4-2).

2.
Insert the axle shaft assembly in

the rear axle housing onto the four

backing plate retaining bolts, feeding

the sensor lead through the hole in the

backing plate.

3.
Seat the sensor lead grommet in

the backing plate.

4.
Install the four nuts on the re-

taining bolts and tighten to specifica-

tions.

5.
Connect the sensor lead to the

rear wiring harness and install two re-

taining straps.

6. Install the rear brake drum and

retain with the Tinnerrhan drum re-

taining nuts.

7.
Install the rear wheel and tire as-

sembly and tighten the wheel nuts to

specifications.

8. Test the vehicle on the hoist to

verify proper operation of the skid

control system.procarmanuals.com

Page 60 of 413

FORD MUSTANG 1969 Volume One Chassis
02-02-41
Brake System

02-02-41

bolt and G-ring in the bottom of the

master cylinder.

8. Install the bleed screw (if so

equipped). Install the gasket (dia-

phragm) in the master cylinder filler

02-02-41
Brake System

02-02-41

bolt and G-ring in the bottom of the

master cylinder.

8. Install the bleed screw (if so

equipped). Install the gasket (dia-

phragm) in the master cylinder filler

cover. Position the gasket as shown in

Figs.
40 and 41. Make sure the gasket

is securely seated.

9. Install the cover and gasket on

the master cylinder and secure the

cover into position with the retainer.

DISC BRAKE CALIPER

ALL MODELS EXCEPT

LINCOLN CONTINENTAL

Disassembly

1.
Remove the caliper assembly

from the vehicle as outlined in Section

2.

2.
Remove the caliper locating pins

from the caliper assembly and lift the

anchor plate from the caliper.

3.
Slide the two outer shoe retain-

ing clips off the retaining pins (Fig.

43).

4.
Remove the two retaining pins,

then remove the outer brake shoe

from the caliper.

5.
Slide the inner brake shoe out-

ward until it is free of the hold-down

springs, then remove the brake shoe.

6. Apply air pressure to the fluid

port in the caliper with a rubber

tipped nozzle (Tool 7000-DD) as

shown in Fig. 44 to remove the piston.

Place a cloth over the piston before

applying air pressure to prevent dam-

age to the piston. If the piston is

seized and cannot be forced from the

FIBER

BLOCK

CALIPER

PISTON

H 1574-B

FIG. 44 —Removing Piston From

Caliper —
All
Models Except

Lincoln Continental
caliper, tap lightly around the piston

while applying air pressure. Care

should be taken because the piston

can develop considerable force due to

pressure build-up.

7.
Remove the dust boot from the

caliper assembly.

8. Remove the rubber piston seal

from the cylinder and discard it.

Cleaning and Inspection

Clean all metal parts with isopropyl

alcohol or a suitable solvent. Use

clean, dry, compressed air to clean out

and dry the grooves and passage ways.

Be sure that the caliper bore and com-

ponent parts are completely free of

any foreign material.

Check the cylinder bore and piston

for damage or excessive wear. Replace

the piston if it is pitted, scored, or the

chrome plating is worn off.

Assembly

1.
Apply a film of clean brake fluid

to the new caliper piston seal and in-

stall it in the cylinder bore. Be sure

the seal does not become twisted and

that it is seated fully in the groove.

2.
Install a new dust boot by setting

the flange squarely in the outer groove

of the caliper bore.

3.
Coat the piston with the speci-

fied fluid and install the piston in the

cylinder bore. Spread the dust boot

over the piston as it is installed. Seat

the dust boot in the piston groove.

4.
Position the inner brake shoe so

that the ears of the shoe rests on the

top of the anchor plate bosses and be-

neath the hold-down springs.

5.
Install new caliper locating pin

insulators in the anchor plate.

6. Position the caliper on the an-

chor plate.

7.
Apply water or isopropyl alcohol

to the caliper locating pins and install

them loosely in the anchor plate. Be

sure the guide pins are free of oil,

grease or dirt.

8. Install the caliper on the spindle

as outlined under Disc Brake Caliper

Assembly.

LINCOLN CONTINENTAL

Disassembly

Do not remove the bridge bolts that

hold the two halves of the caliper to-

gether. The two caliper housings are

shown separated in Fig. 46 for illus-

tration purposes only.
1.
Remove the caliper assembly

from the car as outlined in Section 2.

2.
Remove the two attaching bolts

and the caliper splash shield (Fig. 46).

3.
Remove the two shoe and lining

assemblies.

4.
Remove the flexible brake hose

from the caliper.

5.
Remove the external transfer

tube.

6. Remove the four dust boots from

the caliper housings and piston

grooves.

7.
Clamp the caliper in a vise and

secure it by the mounting flanges on

the inboard housing (Fig. 45).

8. Remove the four pistons from

the cylinder bores with the special tool

shown in Fig. 45. To prevent cocking

with consequent damage to the piston

or bore, rotate the piston with the tool

while pulling it outward at the same

time.
Be careful to avoid scratching or

damaging the outside diameter surface

or dust boot retaining groove of the

piston. Such damage causes poor seal-

ing.

If a piston is so completely seized in

the cylinder bore that it can not be re-

moved with the special tool, the cali-

per housing must be replaced, by posi-

tioning two screwdrivers in the piston

dust boot retaining groove and prying

outward. To prevent cocking, tap the

end of the piston lightly around the

circumference with a hammer, while

the prying force is being applied. Be

careful to avoid damaging the dust

boot retainer in the caliper housing

(Fig. 46). If this method of removal is

used, the pistons must be replaced.

If the caliper dust boot retainer or

retaining groove is damaged or

scratched, pry the retainer out of the

caliper housing with screwdrivers.

Too/-T65P-2
J
18- A

H 1652-A

FIG. 45—Removing or Installing

Pistons —
Lincoln
Continentalprocarmanuals.com

Page 63 of 413

FORD MUSTANG 1969 Volume One Chassis
02-03-02
Specifications

02-03-02

BORE DIAMETERS-BRAKE DRUM, WHEEL CYLINDER AND MASTER

Models

Ford,

Mercury

and

Meteor

Mont ego

and

Fairlane

Falcon

Mustang

and Cougar

Thunderbird

Conti

02-03-02
Specifications

02-03-02

BORE DIAMETERS-BRAKE DRUM, WHEEL CYLINDER AND MASTER

Models

Ford,

Mercury

and

Meteor

Mont ego

and

Fairlane

Falcon

Mustang

and Cougar

Thunderbird

Continental Mark
III

Lincoln Continental
Taxi and Station Wagon

Other

Pass, except Conv. 250, 302 CID Engines

Pass, and Conv. 351, 390, 428 CID Eng.

Convertible 250, 302 CID Engines

Station and Ranchero

9 Inch Brake
-
Passenger Car

10 Inch Brake
•
Station Wagon

10 Inch Brake
•
Passenger Car

200 CID Engine

351,
390, 428 CID Engine

250,
302, CID Engine
CYLINDER

Brake Drum

Inside

Diameter

11.030

11.030

10.000

10.000

10.000

10.000

9.000

10.000

10.000

9.000

10.000

10.000

11.030

11.030

11.090
Boring Umit

(Max.)
®

11.090

11.090

10.060

10.060

10.060

10.060

9.060

10.060

10.060

9.060

10.060

10.060

11.090

11.090

11.130
Wheel Cylinder Bore Dia.

Front
0

1.094

L_ U25

1.125

1.094

1.094

1.094

1.062
0

1.094

1.125

1.062
®

1.094

1.125

N/A

N/A

N/A
Rear
®

0.938

0.938

0.875

0.875

0.875

0.938

0.844®

0.938

0.875

0.844®

0.875

0.875

0.938

0.938

0.938
Master Cylinder Bore Dia.

With Power

Brake
®

1.000

1.000

0.9375

0.9375

0.9375

0.9375

0.9375

0.9375

0.9375

1.000

1.000

1.000

1.000

1.000

1.000
Less Power

Brake
®

1.000

1.000

1.000

1.000

1.000

1.000

1.000

1.000

1.000

1.000

1.000

1.000

N/A

N/A

N/A

©Max. Runout
0.007

(DMax. Allowable Hone
0.003

CD2.755 For
Ford,
Mercury, Meteor with Disc Brakes.

2.381 For Fairlane, Montego, Falcon, Mustang, Cougar with Disc Brakes.

SHOE AND LINING DIMENSIONS-

DISC BRAKES-INCHES
® Front Wheel Cylinder cannot be honed on Falcon or Mustang with
9
inch Brakes.

Lining Material

Lining Size

Lining Area
-
Square Inches

per Segment

Lining Thickness • Nominal

Lining Wear Limit (Front

Surface
of
Shoe)
•
Max.

Lining Taper -Max.

Lining to Rotor Clearance

(Brakes Released)
Ford,
Mercury, Meteor

Thunderbird, Continen-

tal Mark
III

Bonded

7.38x2.27
Outer

5.36x2.03
Inner

12.25 Outer

8.44 Inner

0.394

0.030

0.125

0.000-0.010
Fairlane, Montego

Falcon,
Mustang,

Cougar

Bonded

6.82 x 1.80 Outer

4.90x1.84 Inner

11.30 Outer

8.80 Inner

0.333
Outer

0.362
Inner

0.030

0.125

0.000
• 0.010
Lining Material

Lining Size

Lining Area

Shoe and Lining Thickness

Lining Thickness

Shoe and Lining Maximum

Wear Limit

Lining Maximum Wear Limit

(from front surface
of
shoe)

Lining to Rotor Clearance

(brakes released)
Lincoln Continental

Riveted Fomoco

5.36x1.90

10.03 Sq. In/segment

0.600
nominal

0.436
nominal

0.231

0.066

0.000-0.010

CALIPER CYLINDER BORE DIAMETER -INCHES

TORQUE LIMITS-HUB TO SPINDLE

Ford,
Mercury, Meteor, Thunderbird, Continental Mark

2.755

Mustang, Cougar, Falcon, Fairlane and Montego

2.381

Lincoln Continental

1.938

ROTOR DIMENSIONS

Car Line

Ford,
Mercury, Meteor

Thunderbird, Continental Mark
III

Fairlane, Falcon, Montego, Mustang

and Cougar

Lincoln Continental
Norn.

Thickness

1.180

1.180

0.935

1.240
Diameter

Outside

11.72

11.72

11.29

11.960
Inside

7.785

7.785

7.355

7.785
Description

Hub and Drum or Rotor Assembly to

Front Wheel Spindle
Ft-Lbs

Rotate
hub
while torquing

to 17-25 ft-lbs. Backoff

the adjusting nut 1/2 turn

and retighten to 10-15

inch pounds while rotat-

ing wheel Selectively
posi-

tion
nut
retainer
on ad-

justing nut
so
that a set

of slots are in line with

cotter pin hole. Adjusting

nut should not be rotated

in this operation. Lock
ad-

justing nut and nut retain-

er with cotter pin so that

the cotter
pin end
does

not interfere with seating

of wheel static collector

in spindle hole.procarmanuals.com

Page 68 of 413

FORD MUSTANG 1969 Volume One Chassis
03-01-03
Suspension — Steering, Wheels And Tires — General Service

03-01-03

4.
Connect a tachometer, start the

engine and operate it at idle speed

until the reservoir fluid temperature

rea

03-01-03
Suspension — Steering, Wheels And Tires — General Service

03-01-03

4.
Connect a tachometer, start the

engine and operate it at idle speed

until the reservoir fluid temperature

reaches 165 to 175. This temperature

must be maintained throughout the

test. Valve B may be partially closed

to create a back pressure up to 350

psi to hasten the temperature rise. The

reservoir fluid must be at the proper

level.

5.
With the engine operating at rec-

ommended idle rpm and fluid temper-

ature noted in Step 4, close the manu-

al valve B. The minimum acceptable

pressure reading is 620 psi.

6. If the pressure gauge reading is

below the minimum specification, the

pump is at fault and should be re-

paired with necessary parts.

7.
If the reading is at or above the

minimum specification, the pump flow

is normal. Open manual valve B and

proceed to the Pump Fluid Pressure

Test.

PUMP FLUID

PRESSURE TEST

1.
Keep the lines and tools con-

nected as in the Pump Flow Test.

2.
With manual valves A and B

opened fully, operate the engine at

recommended idle speed (Fig. 2).

Close manual valve A, then manual

valve B. Do not keep both valves

closed for more than 5 seconds as this

would abnormally increase the fluid

temperature and cause undue pump

and/or gear wear.

3.
With the valves fully closed, the

pressure gauge should read 1000 psi

minimum for Ford, Mercury, Meteor

or Thunderbird and 750 psi minimum

for Cougar, Fairlane, Falcon, Monte-

go or Mustang.

4.
If the pressure gauge reading is

below the minimum specification, the

pump is at fault and should be re-

paired with necessary parts.

5.
If the pressure gauge reading is

at or above the minimum specifica-

tions,
the pump is normal and the

power steering gear or power assist

control valve is at fault.

FLUID PRESSURE TEST-

LINCOLN CONTINENTAL AND

CONTINENTAL MARK III

The pressure testing gauge set, tool

T56L-33610-D, requires modification

to make it adaptable for installation

in the power steering hydraulic sys-

tem. The parts required and the modi-

fication procedure are as follows:
OWER STEERING

PRESSURE LINE

INVERTED FLARE

CONNECTOR

%* TUBE x VA" PIPE

FLARED FEMALE COUPW

%' TUBE x VA" PIPE

G1544.A

FIG. 3—Modified Pressure Gauge

Assembly

a. Power Steering Pressure Line

(refer to the appropriate Parts Catal-

og).

b.
Inverted Flare Connector (3/8

inch OD Tube x 1/4 inch Pipe

Thread).

c. Inverted Flare Connector (5/16

inch OD Tube x 1/4 inch Pipe

Thread).

d. Flared Tube Female Coupling

(3/8 inch OD Tube x 1/4 inch Pipe

Thread).

The connectors and the coupling are

standard-type fittings and can be pur-

chased locally.

e. To modify tool T56L-33610-D,

remove the hose from the hand shut-

off valve block. Install the 3/8 inch x

1/4 inch inverted flare connector in

the valve block, and assemble the

pressure line to the connector (Fig. 3).

Assemble the 3/8 x 1/4 inch coupling

and the 5/16-inch connector to the

free end of the hose leading to the.

pressure gauge.

1.
To check the pump pressure, dis-

connect the front and rear sections of

the pressure line over the number 6

cylinder. Connect the modified pres-

sure-testing gauge assembly, tool

T56L-3361O-D, between the two sec-

tions.

2.
Make sure the hand-valve at the

gauge is fully opened. Start the engine

and cycle the steering gear from stop

to stop to warm up the fluid. Check

the fluid level in the reservoir and add

fluid, if necessary.

3.
Turn the steering wheel to the

full right and full left turn positions

and observe the gauge readings.

Hold the wheels in this position

only long enough to obtain an accu-

rate reading. Do not exceed 5 seconds.

The gauge should read between

1120 and 1250 psi. If the pressure is
less than 1120 psi, close the valve at

the gauge and note the pump pressure.

If it is low with the valve closed, it in-

dicates that the pump is not operating

properly. If the pressure goes up with

the valve closed, it indicates that the

low pressure in the system must be

due to internal leakage in the power

unit, providing all connections are

tight.

4.
Remove the pressure testing

gauge set, and connect the pressure

line at the steering gear. Fill and bleed

the system.

FRONT WHEEL ALIGNMENT

CHECKS

Do not attempt to check and adjust

front wheel alignment without first

making a preliminary inspection of

the front-end parts. Refer to Section

3.

Check all the factors of front wheel

alignment except the turning angle

before making any adjustments. The

turning angle should be checked only

after caster, camber, and toe-in have

been adjusted to specifications.

The front wheel alignment specifica-

tions given in Part 3-13, are correct

only when the vehicle is at curb load.

Before checking or adjusting the

alignment factors, the suspension

alignment spacers must be installed to

obtain the curb Height.

EQUIPMENT INSTALLATION

Equipment used for front wheel

alignment inspection must be accu-

rate.
Whenever possible, front wheel

alignment checks should be performed

on stationary wheel aligning equip-

Too/
- T65P3000-A or S

FIG. 4—Typical Front Alignment

Spacer Installation—Cougar,

Fairlane, Falcon,
Montego,
Mustangprocarmanuals.com

Load next 8 pages

Page: < prev 1-8 9-16 17-24 25-32 33-40 41-48 49-56 ... 184 next >

USB brake rotor jack points ECU fuel filter location wheel