1967 CHEVROLET CAMARO steering wheel

BRAKES

SECTION 5

CONTENTS OF THIS SECTION

Duo Servo Brakes

Disc Brakes
Page

5-1 Power Brakes

5-24 Special Tools
Page

5-31

5-32

DUO-SERVO BRAKES

INDEX

Page

General Description 5-1

Maintenance and Adjustments 5-3

Hydraulic Brake Fluid .. . 5-3

Bleeding Hydraulic System 5-3

Pressure Bleeding 5-3

Manual Bleeding 5_4

Push Rod to Main Cylinder Clearance 5-5

Hydraulic Brake Lines 5-5

Hydraulic Brake Hose 5-5

Hydraulic Brake Tubing 5-6

Brake Adjustment. .................... 5-7

Service Brake 5-7

Parking Brake 5-8

Component Replacement and Repairs 5-9

Parking Brake - Chevrolet, Chevelle and

Camaro 5^9

Pedal Assembly 5-9

Front Cable ,. . . 5-9

Center Cable 5-9

Rear Cables. . 5-9
Parking Brake - Chevy n 5-9

Lever Assembly 5-9

Idler Lever 5-11

Front Cable 5-11

Rear Cable . . ; 5-12

Parking Brake - Corvette 5-13

Lever Assembly . . . . 5-13

Front Cable 5-14

Rear Cable . . 5-14

Brake Pedal 5-15

Shoes and Linings 5-16

Organic 5-16

Metallic 5-17

Main Cylinder 5-18

Wheel Cylinders 5-21

Anchor Pin 5-22

Front Wheel 5-22

Rear Wheel 5-22

Brake Drums • 5-22

Brake Pipe Distribution and Switch Assembly . . . . . 5-23

Camaro Pressure Regulator Valve 5-23

GENERAL DESCRIPTION

All 1967 models are equipped with a new split brake

system as a safety feature. If a wheel cylinder or brake

line should fail at either the front end or rear end of

the vehicle, the operator can still bring the vehicle to

a controlled stop. The system is designed with separate

hydraulic systems for the front and rear brake using

a dual master cylinder (fig. 1). The design of the master

cylinder is similar to that used on the 1966 Corvette

in that it has two entirely separate reservoirs and outlets

in a common body casting. The front reservoir and outlet

is connected to the front wheel brakes, and the rear

reservoir and outlet is connected to the rear wheel

brakes. Two pistons within the master cylinder receive

mechanical pressure from the brake pedal push rod and

transmit it through the brake lines as hydraulic pressure

to the wheel cylinders. The filler cap is accessible from

inside the engine compartment.

A new brake pipe distribution and switch assembly

is mounted below the main cylinder. The front and rear

hydraulic brake lines are routed from the main cylinder,

through the brake pipe distribution and switch assembly,

to the front and rear brakes as shown in Figure 2. The

switch is wired electrically to the brake alarm indicator

light on the instrument panel. In the event of fluid loss

in either the front or rear brake system the indicator

on the instrument panel will illuminate red. (The indi-
cator will also' be illuminated when the parking brake is

applied.)

On Camaro models equipped with air conditioning, the

rear brake hydraulic line is routed through a pressure

regulator valve mounted on the left frame side rail

(fig. 3). The valve controls the hydraulic pressure to

the rear brakes resulting in the correct pressure balance

between the front and rear hydraulic systems.

The self-adjusting brakes (fig. 4), used on both front

and rear of all models, are the Duo-Servo single anchor

type which utilize the momentum of the vehicle to assist

in the brake application. The self-energizing or
self-

actuating force is applied to both brake shoes at each

wheel in both forward and reverse motion. The brake

shoe linings are bonded to the shoes.

Wheel cylinders are the double piston type permitting

even distribution of pressure to each brake shoe. To

keep out dust and moisture, both ejads of each wheel

cylinder are sealed with a rubber booC The wheel

cylinders have no adjustments.

The Chevrolet, Chevelle, and Camaro parking brakes

have a foot operated ratchet type pedal mounted to the

left of the steering column. A cable assembly connects

the pedal to an intermediate cable by means of an equal-

izer, where the adjustment for the parking brake is

incorporated. The intermediate cable attaches to the

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-2

DELCO MORAINE MAIN CYLINDER

BENDIX MAIN CYLINDER

Fig.
I—Main
Cylinder

two rear cables which operate the rear service brake.

The Chevy II has a single-stroke, ratchet-type parking

brake release lever, located to the right of the steering

column. The lever is connected to the rear wheel brake

assemblies through a two-piece cable and equalizer

assembly. A dash mounted idler lever multiplies force

applied at the parking brake lever and transmits it to

the equalizer by means of the front cable. The one-piece

rear cable passes through the equalizer and is connected
at each end to an actuating lever within the rear brake

assembly.

The Corvette is equipped with a ratchet-type parking

brake lever located behind the console. The parking

brake cable runs forward from the lever to a pulley

assembly mounted on a frame crossmember, then back

to an equalizer near the rear frame crossmember. A

single piece rear cable passes through the equalizer

and back to the rear service brakes.

— CHEVROLET
CAMARO

Fig.
2—Brake Pipe Distribution and Switch Assembly

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-5

LEVEL CYLINDER

TILTED CYLINDER

Fig.
8—Correct Main Cylinder Fluid Level

expelled brake fluid flows in a solid stream from the

bleeder hose and no bubbles are present, then close

bleeder valve tightly.

6. Remove brake bleeder wrench and bleeder hose from

wheel cylinder bleeder valve.

7. Repeat Steps 2 through 7 on the remaining wheel

cylinders in the correct bleeding sequence (fig. 5).

8. Fill the main cylinder to the levels shown in

Figure 8.

9. Install main cylinder diaphragm and cover.

PUSH ROD TO MAIN CYLINDER CLEARANCE

The brake pedal has a definite stop which is permanent

and not adjustable. This stop consists of a rubber

bumper at the release end of pedal travel. Before

adjusting push rod to main cylinder clearance, make

sure pedal returns to the fully released position freely

and that the pedal retracting spring has hot lost its

tension, then proceed as follows:

1.
Loosen check nut on push rod.

2.
Turn push rod as required to provide correct ad-

justment. Movement of pedal pad before push rod

contacts main cylinder pistons must be 1/16" to

1/4" (fig. 9).

3.
Tighten check nut against clevis, and recheck

movement.

HYDRAULIC BRAKE LINES

Hydraulic Brake Hose

The flexible hoses which carry the hydraulic pressure

from the steel lines to the wheel cylinders are carefully

designed and constructed to withstand all conditions of

stress and twist which they encounter during normal

vehicle usage.
The hoses require no service other than periodic

inspection for damage from road hazards or other like

sources. Should damage occur and replacement become

necessary, the following procedure is to be followed.

Removal

1.
Separate hose from steel line by turning double

flare connector out of hose fitting.

2.
Remove "U" shaped retainer from hose fitting and

withdraw hose from support bracket.

3.
Turn hose fitting out of wheel cylinder inlet.

Replacement

1.
Install new copper gasket on cylinder end of hose

(male end).

2.
Moisten threads with brake fluid and install hose in

wheel cylinder inlet.

3.
With weight of car on wheels and suspension in

normal position (front wheels straight ahead) pass

female end of hose through support bracket, allowing

hose to seek its own position. Insert hex of hose

fitting into the 12 point hole in support bracket

in position which induces least twist to hose (figk 10).

NOTE:
Do not twist hose unduly during ^

operation as its natural curvature is absolutely

necessary to maintain proper hose-tot

suspension clearance through full movement o£

the suspension and steering parts.

4.
Install "U" shaped retainer to secure hose in sup-

port bracket.

5. Inspect by removing weight completely from wheel,

turn wheels from lock to lock while observing hose

position. Be sure that hose does not tough other

parts at any time during suspension or wheel travel.

If contact does occur, remove hose retainer and

rotate the female hose end in the support bracket

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES
5-24

DISC BRAKES

INDEX

Page

General Description
. 5-24

Maintenance
and
Adjustments
5-24

Bleeding Hydraulic System
5-24

Parking Brake Adjustment
-
Corvette
5-24

Component Replacement
and
Repairs
5-25
Page

Brake Shoes
. . . . . 5-25

Brake Caliper
5-26

Brake Disc
5-29

Main Cylinder.
5-30

Parking Brake Shoes
-
Corvette
5-30

GENERAL DESCRIPTION

Four wheel disc brakes
are
standard equipment
on

the
1967
Corvette,
as in 1966. The
Corvette
may
also

be equipped with heavy duty disc brakes which include

new front calipers, shoes, linings,
and
rear pressure

regulator valve. This heavy duty option
is
used
in

conjunction with
a
vacuum power unit. Front wheel disc

brakes
are
installed
as
optional equipment
on
Chevrolet,

Chevelle, Camaro,
and
Chevy
II
models.

The disc brake,
(fig. 35),
consists
of a
fixed caliper,

rotating disc, splash shield,
and
mounting bracket.
The

caliper assembly contains four pistons and two shoe
and

lining assemblies with
the
lining riveted
to the
steel

shoes.
A
seal
and
dust boot
are
installed
on
each piston,

with
a
piston spring
in the
caliper cylinder bore beneath

each piston.
A
retaining pin extends through each caliper

half
and
both shoes
to
hold
the
shoes and linings
in
posi-

tion
in the
caliper.
On
Corvette heavy duty disc brakes,

two retaining cotter pins
are
used
at
each end
of the

caliper
to
secure
the
shoes
and
linings. Machined
sur-

faces within
the
caliper prevent
the
shoe
and
lining
assembly from rotating with
the
brake disc when pres-

sure
is
applied.

The disc, which
has a
series
of air
vent louvers
to

provide cooling,
is
mounted
on the
front wheel-hub.

The caliper straddles
the
disc and mounts
on a
mounting

bracket attached
to the
steering knuckle with
two
bolts.

The Corvette heavy duty option includes
a
pressure

regulator valve mounted
in the
rear brake line just

below
the
main cylinder. Chevrolet, Chevelle, Camaro,

and Chevy
n
models with disc brakes have
a
pressure

regulator valve mounted
in the
front brake line just

below
the
main cylinder. The valve controls
the
hydraulic

pressure
to the
front
or
rear brakes,
as
applicable,

resulting,
in the
correct pressure balance between
the

front
and
rear hydraulic systems. This valve guards

against premature .lock-up
of
front
or
rear wheels when

brakes
are
applied.

Maintenance, adjustment,
and
service operations which

are
not
included
in
this section
are the
same
as for

the Duo-Servo type brakes.

MAINTENANCE
AND
ADJUSTMENTS

BLEEDING HYDRAULIC SYSTEM

The operation
of
bleeding
the
disc brake hydraulic

system
is the
same
as for
Duo-Servo system outlined

in
the
front
of
this section. Note
the
exceptions below

and refer
to
bleeding procedures under Duo-Servo

brakes.

1.
When pressure bleeding equipment
is
used,
the

correct pressure setting
for
bleeding disc brakes

is 10-2.0
lbs. on
Corvette,
and 40 lbs. on all
other

models.

2.
The
front calipers contain
one
bleeder valve.
The

rear calipers
on
Corvette contain two bleeder valves

(one inboard
and one
outboard) which necessitates

the removal
of the
rear wheels
for
bleeding.

3.
Tapping
the
caliper with
a
rawhide mallet
as the

fluid
is
flowing
out may
assist
in
obtaining
a
good

bleeding
job.

4.
On
Chevrolet, Chevelle, Camaro
and
Chevy
II, the

spring loaded
end of the
pressure regulator valve

(fig.
36)
must
be
held (valve
in
open position) while

bleeding. This
is
done
by
depressing
and
holding

in
the
plunger
in the
end
of
the valve either
by
hand,

by taping,
or by
clamping.
PARKING BRAKE-CORVETTE

Adjustment

1.
Raise rear
end of
vehicle
and
place
on
jack stands.

2.
Remove rear wheels.

3/
Loosen brake cables
at the
equalizer until
the
park-

ing brake levers move freely
to the "off"
position

with slack
in the
cables.

4.
Turn
the
disc until
the
adjusting screw can
be
seen

through
the
hole
in the
disc.

5. Insert
an
adjusting tool
or
screw driver through
the

hole
in the
disc
and
tighten
the
adjusting screw
by

moving your hand away from
the
floor
on
both
the

left and right sides
(fig. 37).

6. Tighten until
the
disc will
not
move, then back
off

ten
(10)
notches.

7. Apply
the
parking brake four
(4)
notches from inside

the
car.

8. Tighten
the
brake cables
at the
equalizer
to
produce

a light drag with
the
wheels mounted.

9. Fully release
the
parking brake handle
and
rotate

the rear wheels.
No
drag should be evident with
the

handle released.

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-28

Fig.
40—Installing Piston in Caliper Bore Using

Tool J-22591
Fig.
41—Installing Boot Seal in Caliper Bore

Using Tool J-22592

5.
Check the fit of the piston in the bore using a feeler

gage.
Clearance should be as follows:

2 1/16 inch Bore .0045 to .010

1 7/8 inch Bore .0045 to .010

1 3/8 inch Bore .0035 to .009

If the bore is not damaged, and the clearance exceeds

either of the upper limits, a new piston will be required.

Assembly

1.
Assemble the seal in the groove in the piston which

is closest to the flat end of the piston. The lip on

the seal must face toward the large end of the

piston. Be sure lips are in the piston groove and do

not extend over the step in the end of the groove.

2.
Place the spring in the bottom of the piston bore.

3.
Lubricate the seal with dean brake fluid.

4.
Install the piston assembly in the bore using appli-

cable piston rign compressor Tool J-22639, 22629

or 22591 as shown in Figure 40. Use care not to

damage the seal lip as piston is pressed past the

edge of the bore. .

5.
Assemble the boot in the groove of the piston closest

to the concave end of the piston. The fold in the boot

must face toward the end of the piston with the seal

on it.

6. Depress the pistons and check that they slide

smoothly into the bore until the end of the piston is

flush with the end of the bore. If not, re check piston

assembly and location of the piston spring and the

seal.

7.
Position applicable boot seal installer Tool J-22592,

J-22628, or J-22638 over the piston and seat the

steel boot retaining ring evenly in the counterbore

as shown in Figure 41. The boot retaining ring must

be flush or below the machined face of the caliper.

Any distortion or uneven seating could allow con-

taminating and corrosive elements to enter the bore.
8. Position the t:O}> rings in the small cavities around

the brake fluid transfer holes in both ends of the

outboard caliper halves. Lubricate the hex head

. bolts with Delco Brake Lube or clip in clean brake

fluid. Fit caliper halves together and secure with

bolts.
Refer to torque specifications in rear of

manual for correct torque valves.

Installation

1.
Carefully mount the assembled caliper over the edge

of the disc. Use a putty knife to depress pistons so

that the caliper can be lowered into position on the

disc (fig. 42). Use care to prevent damage to boots

• on the edge of the disc as the caliper is mounted.

2.
Secure the caliper to the mounting bracket with two

hex head bolts. Refer to torque specifications in

rear of manual for correct torque values.

CAUTION: If replacing old shoe assemblies,

be sure to get the shoes in the same position

from which they were removed. New shoe as-

semblies have an arrow printed on the back,

showing the direction of forward disc rotation.

3.
Install the shoe and lining assemblies as outlined in

this section.

4.
On Chevrolet and Corvette front calipers, place a

new copper gasket on the male end of the front

wheel brake hose. On all models, install brake hose

in the calipers. With the wheels straight ahead,

pass the female end of the brake hose through the

support bracket.

5.
Make sure the tube seat is clean and connect the

break line tube nut to the caliper. Tighten securely.

6. Allowing the hose to seek a normal position, without

twist, insert hex of the hose fitting into the 12-point

hole in the support bracket and secure it in place

with the "V"-shaped retainer. Turn the steering

geometry from lock to lock while observing the hose.

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE
6-12

ENGINE
MECHANICAL

IN LINE

INDEX

Page

General Description . „ 6-12

Component Replacement and Adjustment 6-12

.Engine Assembly 6-12

Removal 6-12

Installation 6-13

Manifold Assembly 6-14

Removal . 6-14

Installation 6-14

Rocker Arm Cover . 6-14

Removal 6-14

mstallation . . . 6-14

Valve Mechanism
......
1 6-14

Removal 6-14

Installation and Adjustment . 6-14

Valve Lifters
..............
6-15

Locating Noisy Lifters
„.;....
6-15

Removal
.'.*...•
6-15

Installation . 6-15

Valve Stem Oil Seal and/or Valve Spring . 6-16

Replacement . 6-16

Cylinder Head Assembly . 6-16

Removal 6-16

Installation . 6-16

Oil Pan . » 6-17

Removal . . . ; . . 6-17

Installation
.........
. 6-17

Oil Pump . 6-18
Page

Removal . 6-18

Installation . 6-18

Oil Seal (Rear Main) . 6-19

Replacement 6-19

Crankshaft Pulley and Hub 6-19

Removal 6-19

Installation 6-19

Torsional Damper 6-19

Removal 6-19

Installation 6-19

Crankcase Front Cover . 6-20

Removal . 6-20

Installation 6-20

•
Oil Seal (Front Cover) 6-20

Replacement 6-20

Camshaft 6-21

Measuring Lobe Lift . ... .
.-.••.-.
6-21

Removal 6-21

Installation 6-22

Timing Gears
..••••.............••• 6—22

Replacement
6-22

Flywheel
6-22

Removal
* 6-22

Installation
6-22

Engine
Mounts
6-23

Replacement
(Front)
6-23

Replacement
(Rear)
. 6-23

GENERAL DESCRIPTION

The
In
Line engines
(fig. 1L)
covered
in
this section

are
the 1H3 cu. in. L4, the 194,
230
and
250
cu. in. L6,

regardless
of
which passenger vehicle they
are
used
in.

This section covers
the
removal
and
installation
of en-

gine assemblies;
the
removal, installation
and
adjustment

of some sub-assemblies
and
replacement
of
some
com-

ponents.
For
service
to all
components
and
sub-assem-

blies (after removal)
and
removal
of
some sub-assem-

blies,
refer
to
Section
6 of the
Chassis Overhaul Manual.
Because
of the
interchangeability
and
similarity
of

many engine sub-assemblies
and
engine parts, regardless

of which passenger vehicle they
are
used
in,
typical illus-

trations
and
procedures
are
used except where specific

illustrations
or
procedures
are
necessary
to
clarify
the

operation. Although illustrations showing bench opera-

tions
are
used, most single operations, when
not
part
of a

general overhaul, should
be
performed
(if
practical) with

the engine
in the
vehicle.

COMPONENT REPLACEMENT
AND
ADJUSTMENT

ENGINE ASSEMBLY

Removal

1.
Drain cooling system
and
engine
oil.

2.
Remove
air
cleaner
and
disconnect battery cables
at 7.

battery.

3.
Remove hood
as
outlined
in
Section 11.

4.
Remove radiator
and
radiator shroud
as
outlined
in

Section 13.

5.
Remove
fan
blade
and
pulley
as
outlined
in
Section

6K.

6. Disconnect wires
at:

• Starter Solenoid
8.

• Delcotron
9.
Temperature Switch

Oil Pressure Switch

Coil

Disconnect:

Accelerator linkage
at
manifold bellerank.

Exhaust pipe
at
manifold flange.
.

Fuel line (from tank)
at
fuel pump.

Vacuum line
to
power brake unit
at
manifold
(if

so equipped).

• Power steering pump lines
at
pump
end (if so

equipped).

Raise vehicle
and
place
on
jack stands.

Remove propeller shaft.

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE 6-14

b.
Bolt transmission to engine, then raise engine and

transmission assembly and install flywheel to

converter attaching bolts.

c. Install converter
housing*
underpan and starter.

3.
Tilt and lower engine and transmission assembly into

the chassis as a unit, guiding engine to align front

mounts with frame supports.

4.
Install front mount through bolts and torque to

specifications.

5.
Raise engine enough to install rear crossmember,

then install crossmember, install rear mount, lower

engine and torque bolts to specifications.

6. Remove lifting device and lifting adapter then install

rocker arm cover as outlined.

7.
On synchromesh equipped vehicles, install clutch

cross shaft engine bracket, then adjust and connect

clutch as outlined in Section 7.

8. Connect:

• Speedometer cable.

• Shift linkage at transmission.

9; Install propeller shaft.

10.
Remove jack stands and lower vehicle.

11.
Connect:

Power steering pump lines (if disconnected).

Vacuum line to power brake unit (if disconnected).

Fuel line at fuel pump.

Exhaust pipe at manifold flange.

Accelerator linkage at manifold bellcrank.

12.
Connect wires at:

Coil

Oil pressure switch

Temperature switch

Delcotron

Starter solenoid

13.
Install pulley, fan blade and fan belt as outlined in

Section 6K.

14.
Install radiator and shroud as outlined in Section 13.

15.
Install and adjust hood as outlined in Section 11.

16.
Connect battery cables.

17.
Fill with coolant, engine oil and transmission oil,

then start engine and check for leaks.

18.
Perform necessary adjustments and install air

cleaner.

MANIFOLD ASSEMBLY

Removal

1.
Remove air cleaner.

2.
Disconnect both throttle rods at bellcrank and re-

move throttle return spring.

3.
Disconnect fuel and vacuum lines at carburetor.

Disconnect choke cable on \A engines.

4.
Disconnect crankcase ventilation hose at rocker arm

cover.

5.
Disconnect exhaust pipe at manifold flange and dis-

card packing.

6. Remove manifold attaching bolts and clamps then

remove manifold assembly and discard gaskets.

7.
Check for cracks in manifold castings.

8. If necessary to replace either intake or exhaust

manifolds, separate them by removing one bolt and

two nuts at center of assembly. Reassemble mani-

folds using a new gasket. Tighten finger tight and

torque to specifications after assembly to cylinder

head. Transfer all necessary parts.
Installation

1.
Clean gasket surfaces on cylinder head and

manifolds*

2.
Position new gasket over manifold end studs on head

and carefully install the manifold in position making

sure the gaskets are in place.

3.
Install bolts and clamps while holding manifold in

place with hand.

4.
Torque bolts to specifications.

NOTE: On L6 engines center bolt and end bolt

torque differ.

5.
Connect exhaust pipe to manifold using a new

packing.

6. Connect crankcase ventilation hose at rocker arm

cover.

7.
Connect fuel and vacuum lines at carburetor.

8. On L4 engines connect choke cable and adjust as out-

lines in Section 6M.

9. Connect throttle rods at bellcrank and install throttle

return spring.

10.
Install air cleaner, start engine, check for leaks and

adjust carburetor idle speed and mixture.

ROCKER ARM COVER

Removal

1.
Disconnect crankcase ventilation hose(s) at rocker

arm cover.

2.
Remove air cleaner.

3.
Disconnect temperature wire from rocker arm cover

clips.

4.
Remove rocker arm cover. '

CAUTION: Do Not pry rocker arm cover loose

Gaskets adhering to cylinder head and rocker

arm cover may be sheared by bumping end of

rocker arm cover rearward with palm of hand or

a rubber mallet.

Installation

1.
Clean gasket surfaces on cylinder head and rocker

arm cover with degreaser then, using anew gasket,

install rocker arm cover and torque bolts to

specifications.

2.
Connect temperature wire at rocker arm cover clips.

3.
Install air cleaner.

4.
Connect crankcase ventilation hoses.

VALVE MECHANISM

Removal

1.
Remove rocker arm cover as outlined.

2.
Remove rocker arm nuts, rocker arm
balls,
rocker

arms and push rods.

NOTE:
Place rocker arms, rocker arm balls

and push rods in a rack so they may be rein-

stalled in the same location.

Installation and Adjustment

NOTE:
Whenever new rocker arms and/or

rocker arm balls are being installed, coat bear-

ing surfaces of rocker arms and rocker arm

balls with Molykote or its equivalent.

1.
Install push rods,

socket.
Be sure push rods seat in lifter

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE 6-25

refer to Section 6 of the Chassis Overhaul Manual.

Because of the interchangeability and similarity of

many engines, engine sub-assemblies and engine parts,

regardless of which passenger vehicle they are used in,

typical illustrations and procedures are used except
where specific illustrations or procedures are necessary

to clarify the operation. Although illustrations showing

bench operations are used, most single operations, when

not part of a general overhaul, should be performed (if

practical) with the engine in the vehicle.

COMPONENT REPLACEMENT AND ADJUSTMENT

ENGINE ASSEMBLY

Removal

• .1. Drain cooling system and engine oil.

2.
Remove air cleaner and disconnect battery cables at

battery.

3.
Remove hood as outlined in Section 11.

4.
Remove radiator and shroud as outlined in Sec-

tion 13.

5. Remove fan blade and pulley as outlined in Sec-

tion 6K.

6. Disconnect wires at:

• Starter solenoid

• Delcotron

• Temperature switch

• Oil pressure switch

• Coil

7. Disconnect:

• Accelerator linkage at pedal lever.

• Exhaust pipes at manifold flanges.

• Vacuum line to power brake unit at manifold (if

so equipped),

• Power steering pump lines at pump end (if so

equipped).

• Fuel line (from tank) at fuel pump.

• Engine cooler lines (if so equipped).

• Oil pressure gauge line (if so equipped).

8. Raise vehicle and place on jack stands.

9. Remove propeller shaft.

NOTE:
If plug for propeller shaft opening

in transmission is not available, drain

transmission.

10.
Disconnect:

• Shift linkage at transmission.

• Speedometer cable at transmission.

• Transmission cooler lines (if so equipped).

11.
On synchromesh equipped vehicles, disconnect clutch

linkage at cross-shaft then remove cross-shaft en-

gine bracket.

12.
Remove rocker arm covers as outlined, then attach

engine lifting adapter at the proper cylinder head bolt

locations.

13.
Remove front mount bolts.

14.
Attach lifting device and raise engine to take weight

off front mounts, then remove rear mount bolts.

15.
Raise engine to take weight off rear mount, then re-

move crossmember.

NOTE:
On Chevrolets it will be necessary to

remove mount from transmission before cross-

member can be removed.

16.
Remove engine-transmission assembly from vehicle

as a unit.

17.
Remove transmission (and clutch):
Synchromesh Transmission

a. Remove clutch housing cover plate screws.

b.
Remove bolts attaching the clutch housing to en-

gine block then remove transmission and clutch

housing as a unit.

NOTE:
Support the transmission as the last

mounting bolt is removed, and as it is being

pulled away from the engine (to prevent damage

to clutch disc).

c. Remove starter and clutch housing rear cover

plate.

d. Loosen clutch mounting bolts a turn at a time (to

prevent distortion of clutch cover) until the spring

pressure is released. Remove all bolts, clutch

disc and pressure plate assembly.

Automatic
Transmission

a. Lower engine, secured by the hoist, and support

engine on blocks.

b.
Remove starter and converter housing underpan.

c. Remove flywheel-to-converter attaching bolts.

d. Support transmission on blocks.

e. Remove transmission-to-engine mounting bolts.

f. With the hoist attached, remove blocks from the

engine only and slowly guide the engine from the

transmission.

18.
Mount engine in stand.

Installation

1.
Attach lifting device to engine and remove engine

from engine stand.

2.
Install transmission (and clutch):

Synchromesh Transmission

a. Install the clutch on flywheel as outlined in Sec-

tion 7.

b.
Install clutch housing rear cover and starter.

c. Install transmission and clutch housing as out-

lined in Section 7.

d. Install clutch housing cover screws and tighten

securely.

Automatic
Transmissions

a. Position engine adjacent to the transmission and

align the converter with the flywheel.

b.
Bolt transmission to engine, then raise engine and

transmission assembly and install flywheel to

converter attaching bolts.

c. Install converter housing underpan and starter.

3.
Tilt and lower engine and transmission assembly into

the chassis as a unit, guiding engine to align front

mounts with frame supports.

4.
Install front mount bolts and torque to specifications.

5. Raise engine enough to install rear crossmember,

then install crossmember, install rear mount, lower

engine and torque rear mount to specifications.

CHEVROLET CHASSIS SERVICE MANUAL