1967 CHEVROLET CAMARO battery location

FUEL TANK
AND
EXHAUST SYSTEMS
8-18

CORVETTE

FUEL TANK

INDEX

Page

General Description.
. 8-18

Service Operations
8-18

Fuel Tank
8-18

Gauge Sending Unit
8-20

Fuel Lines.
8-20

GENERAL DESCRIPTION

20 GALLON TANK

Fig.
21
—Corvette Fuel Tanks

The Corvette
is
equipped with
a
standard
20
gallon

(approx.) tank
or an RPO 36
gallon (approx.) fiberglass

tank
(fig. 21). The
tanks
are
installed
at the
very rear

of
the
vehicle, convenient
for
direct fuel filling into
the

tank.
The
tanks
are
held
in
place
by
two metal straps
at-

tached individually
to a
removable
gas
tank frame
sup-

port.
Two
guides
at the end of
the straps
are
adjustable

for securing
the
straps onto
the
tank support. The tank

support
is
secured
to the
frame rail with flat washers,

lockwashers, bolts
and
nuts.
The
tanks' rest
on six
felt

anti-squeak pads.
One pad
centers
on the
rear frame

crossmember
and one at
each side
on the
same cross-

member.
At the
same rear location two pads
are
placed

on
the
tank
at the
metal support strap (rear) attachment
location
and
another anti-squeak
pad
cemented
on the

support
at
the front
of
the tank.

The fuel tanks
are
equipped with
a gas
gauge metering

unit,
a
fuel pickup, fuel strainer
and
vent line.
If it be-

comes necessary,
the
tank
can be
completely drained
by

removing
the
fuel pickup hose which
is
located
at
the
bot-

tom
of the
tank,
or
by removing the metering
for
quicker

draining.

A pressure vacuum type, positive vented design
cap,

conforming
to
I.C.C. regulations,
is
used on both regular

production
and
optional fuel tanks.
The cap is
inter-

changeable with past model tanks
for
service replace-

ment purposes.

SERVICE OPERATIONS

FUEL TANK

CAUTION:
IF THE GAS
TANK SHOULD
BE

REMOVED
AND
INSTALLED, CARE SHOULD

BE EXERCISED
TO
AVOID PUNCTURING,

DROPPING
OR
DENTING
THE GAS
TANK.

Removal
(20
Gallon Tank)

WARNING: FIRST REMOVE BATTERY

CABLE.
1.
Remove
the
spare tire from tire carrier.

2.
Remove spare tire carrier bolted attachments
and

carrier
(fig. 22).

3.
Remove
the "U"
bolt attachments
at
both rear tail

pipe
(See
Figure
23).

4.
Separate
the
exhaust system
at
the transmission sup-

port crossmember
by
loosening
the "U"
bolt nuts.

5. Remove both rear muffler brackets from
the
frame

and slide
the
muffler system rearward.

CHEVROLET CHASSIS SERVICE MANUAL

CHASSIS SHEET METAL 11-4

FENDERS

Fenders are adjustable with shims at the cowl and

rocker panel. To add or remove shims, loosen bolts at

shim locations (fig. 7) and carefully apply force with pry

bar to provide clearance for shim removal or installa-

tion.
SHEET METAL ADJUSTMENTS

For proper operation of doors and hood, and for pre-

sentable appearance, adjust front sheet metal to the tol-

erances shown in Figures
4-
and 5.

COMPONENT PART REPLACEMENT

NOTE: When replacing sheet metal compo-

nents on Chevrolet or Chevelle, note position and

attachment of all seals and dust shielding and

replace as necessary.

BATTERY TRAY

Removal

1.
Disconnect battery cables.

2.
Remove screw retaining battery hold down clamp and

remove battery from vehicle.

3.
Remove screws retaining battery tray to fender skirt

and radiator support.

4.
On Chevrolet, remove headlamp bezel and remove

screw retaining tray to radiator support.

5.
Remove battery tray from vehicle.

Installation

Reverse removal procedure.

RADIATOR SUPPORT

Removal

1.
Remove front bumper (Section 14).

Fig.
3 - Hood Hinge - Chevrolet
2.
Remove grille and related components (Section 13).

3.
Remove battery tray as outlined above.

4.
Remove all electrical connections from radiator

support.

5.
Remove windshield washer bottle from bracket on

radiator support.

6. Remove shroud and radiator (Section 13).

7.
Remove screws and bolts securing support to skirts,

fenders, and frame horns (figs. 8 and 9).

8.. Spread fenders apart enough to allow support move-

ment and remove support from front of vehicle.

Installation

1.
Position the radiator support in vehicle", aligning

mounting screw and bolt holes with drift punch.

2.
install screws and bolts loosely until all are started.

3.
Replace all parts removed following removal proce-

dure in reverse order.

4.
Refer to torque specifications in rear of manual for

correct torque values.
•

5.
Aim headlamps as outlined in Section 12.

FENDER ASSEMBLY

Removal

1.
Remove hood with hinges from vehicle as outlined in

this section.

2.
On Chevrolet models, remove headlamp bezels and

headlamps; on Chevelle models, remove grille ex-

tension panels (fig. 1 or 2 as applicable).

3.
Disconnect wiring harness clips from fender to be

removed.

4.
If applicable, remove horn assembly from fender.

5.
If applicable, remove radio antenna.

6. Remove fender brace (fig. 1 or 2 as applicable).

7.
Remove screws retaining fender to radiator support,

skirt, cowl, filler panel, tie bar, and rocker panel.

Note number and location of shims removed from

locations shown in Figure 7.

8. Remove fender from vehicle.

Installation

Refer to disassembly procedure for location of screws

and install screws loosely. Install the shimmed screws

at rocker panel and cowl and adjust fender (figs. 4 and 5)

before tightening other screws. Always start adjustment

with original amount of shims, then add or remove shims

as required.

FENDER SKIRT

Removal

CAUTION: Chevelle air conditioned models

have condenser hoses routed through the right

front fender skirt. Cut skirt and bend as neces-

sary to move hoses clear of skirt. If necessary,

refer to Section 1A for air conditioning compo-

nents and procedures.

CHEVROLET CHASSIS SERVICE MANUAL

CHASSIS SHEET METAL 11-14

location is shimmed; thus keeping the fender mount-

ing bolts from crushing in the fender mounting

flange.

If shimming is done without the fenders being disas-
asembled, it is suggested that fender mounting bolts

rearward of radiator support be loosened while shims

are inserted and sheet metal fit is checked. Tighten

shimmed mounting bolts first, then all others.

COMPONENT PART REPLACEMENT

BATTERY TRAY (FIG. 21)

Removal

1.
Disconnect battery cables.

2.
Remove screw retaining battery hold down clamp.

3.
Remove battery from vehicle.

4.
Remove screws retaining tray assembly to fender

skirt and support, and remove tray from vehicle.

Installation

Reverse removal procedure.

RADIATOR SUPPORT (FIG. 22)

Removal

1.
Remove grille and related components (Section 13).

Remove battery tray as outlined in this section.

Remove shroud attaching screws and remove shroud

if vehicle is so equipped.

Remove horn relay, horns, voltage regulator, and

wiring harness from radiator support.

Remove shroud and radiator (Section 13)o

Remove screws attaching radiator support to frame,

skirts,
fenders.

Remove radiator support from vehicle (fig. 23).

Installation

1.
Position radiator support in vehicle; align mounting

screw and bolt holes with drift punch.

Install screws and bolts loosely until all are started,

then tighten.

3.
Complete installation following removal procedure in

reverse order. Refer to torque specifications at rear

of manual for correct torque values.

4.
Aim headlamps as outlined in Section 12.

FRONT FENDER ASSEMBLY

Removal

1*
Remove headlamp dooro

2.
Open hood and remove screws joining fender top
2.

Fig. 20 - Front Fender Shimming
Fig.
21 - Battery Tray

flange to skirt. Remove, and record number of

shims at first cap screw forward of windshield (fig.

24).

3.
Remove screw located on upper surface of headlamp

cavity.

4.
From under forward end of fender, remove screw

retaining fender to radiator support.

5.
From inboard side of rocker panel extension, remove

cap screw retaining fender to extension. Remove,

and record number of shims.

6. Separate headlamp filler panel from fender by re-

moving remaining screws.

7.
Remove fender from vehicle.

Installation

1.
Inspect condition of cowl-to-fender seal and replace,

if necessary, as shown in Figure 25.

2.
Install headlamp filler panel on fender.

3.
Position fender on vehicle. Note that eowl-to-fender

seal must be positioned so that outer edge points

toward front of vehicle. Align all mounting screw

and bolt holes with drift punch and install all screws

and bolts loosely. Do not tighten any screws or bolts

until all are started. Refer to removal rocedure

for screw and bolt locations.

4.
Replace shims taken out when fender was removed

from vehicle and continue as outlined under Main-

tenance and Adjustments—Fender Adjustment.

5.
Install headlamp door and cheek headlamp aiming

as outlined in Section 12.

CHEVROLET CHASSIS SERVICE MANUAL

5.

6.

7.

8.
2.
Install all fender mounting screws, replacing original

shimming. Refer to removal procedure for screw

location.

3.
Install hydraulic lines at main cylinder and right

hand skirt. Install fuel line at right hand skirt.

4.
Install steering gear as outlined in Section 9. Do

not fail to perform adjustment procedure listed under

Mast Jacket - Installation.

CAMARO

INDEX

Page

General Description 20

Maintenance and Adjustments 20

Hood / . 20

Hinge 20

Bumpers ' . . . 20

Catch Assembly 21

Lock . 21

Fenders 21

Sheet Metal 22
CHASSIS SHEET METAL 11-19

Install pitman arm as outlined in Section 9 under

Maintenance and Adjustments - Steering Gear Ad-

justments.

Remove jack stands and jack.

Bleed brakes as outlined in Section 5.

Perform body alignment as outlined in Fisher Body

Service Manual.

Page

Component Part Replacement . 22

Battery Tray 22

Radiator Support 22

Fender and Skirt Assembly 22

Hood Assembly . 22

Lock and Catch Assembly 22

Trim and Insulation . . . 24

Cowl Vent Grille . . 24

Fig.
32 - Front End Sheet Metal - Camaro

1.
Fender

2.
Hood Hinge

3. Hood

4.
Cowl Vent Grille
5. Trim

6. Molding

7. Fender Extension

8. Bumper Bracket
9. Valance Pane!

10.
Header Panel

11.
Radiator Support

12.
Radiator
13.

14.

15.
Shroud

Hood Lock

Radiator Cap
16.

17.

18.
Bracket (V-8

Hood Catch

Brace
Engine
Only)
19.

20.

21.
Skirt

Seal

Battery
Tray

CHEVROLET CHASSIS SERVICE MANUAL

CHASSIS SHEET METAL 11-20

GENERAL DESCRIPTION

The Camaro sheet metal components are much the

same as other Chevrolet passenger models as shown in

Figure 32. The front end design is such that servicing

of the fenders and skirts is most efficiently performed
by removing the fender and skirt as an assembly. Refer

to Section 14 for bumper service procedures, Section 13

for radiator and grille, and Section 1A for air condition-

ing components.

MAINTENANCE AND ADJUSTMENTS

HOOD ADJUSTMENT

The Camaro hood is adjusted in the conventional man-

ner, by adjustment of the hood bumpers and hinges. The

two hood bumpers are located on each side at the top of

the radiator support. Do not attempt hood latch adjust-

ments until the hinges and bumpers are correctly ad-

justed. Latch adjustments are made so that effort re-

quired to open and close the hood is reasonable, and

hood alignment obtained by hinge and bumper adjust-

ment is maintained when the hood is closed. Note that

the hood latch is not designed to correct basic hood mis-

alignment.

HOOD HINGE (Fig. 33)

NOTE: The body mounted portion of the hood

hinges are slotted to provide up and down move-

ment. The hood mounted end is slotted to pro-

vide forward and rearward movement.

1.
Scribe a. line around the entire. hinge plate to be

repositioned.

2.
Loosen the appropriate screws and shift the position

of the hood into correct alignment using the scribe

marks to check amount of movement. Check align-

ment by tightening screws and closing the hood.

HOOD BUMPERS

Adjust hood bumpers so that hood top surface is flush

with fender and header panel top surfaces. See Figure

34 for correct sheet metal adjustment dimensions.

HOOD CATCH AND LOCK (Fig. 35)

Adjust hood lock bolt so that top surface of hood is

flush with top surface'of header panel. The distance that

the lock bolt protrudes out of the lock plate should be

adjusted so that the hood bumpers are slightly com-

pressed by the fully latched hood, and effort required

to release the hood catch is reasonable. Close the hood

and insure catch engages securely.

FENDERS

Fenders are adjustable with shims at the cowl and

rocker panel. To add or remove shims, loosen bolts
Fig. 33 - Hood Hinge - Camaro

at shim locations (fig. 36) and carefully apply force with

pry bar to provide clearance for shim removal or in-

stallation.

SHEET METAL

For proper operation of doors and hood, and for pre-

sentable appearance, adjust front sheet metal to the di-

mensions shown in Figure 34.

COMPONENT PART REPLACEMENT

NOTE: When replacing sheet metal compo-

nents on Camaro, note position and attachment

of all seals and dust shielding and replace if

necessary.

BATTERY TRAY

Removal

1.
Disconnect battery cables and remove battery from

vehicle.

2.
Remove screws securing battery tray to fender skirt

and radiator support.

3.
Remove battery tray from vehicle.
Installation

Install battery tray following removal procedure in

reverse order.

RADIATOR SUPPORT

Removal

1.
Raise hood, disconnect battery cables, and remove

battery.

2.
Remove front bumper (Section 14).

3.
Remove grille and related components (Section 13).

4.
Disconnect horns, horn relay, voltage regulator,

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-2

FJg.
1 - Fuse Panel Assembly

All power window and tailgate circuits require the igni-

tion switch to be "ON" to open or close the windows un-

like past model designs which were operated independ-

ently of the ignition switch.

The windshield wiper and washer switch is new in that

washer button in the center of the knob has been deleted
and its function will be accomplished by pushing the knob.

A set screw is used to retain the knob to the shaft.

In addition to fuses, the wiring harness incorporates

fusible links to protect the wiring. Links are used rather

than a fuse in wiring circuits that are not normally fused,

such as the ignition circuit. Fusible links in the Chevro-

let wiring are four gauge sizes smaller than the cable it

is designed to protect. The links are marked on the

insulation with wire gauge size because of the heavy insu-

lation which makes the link appear a heavier gauge than it

actually is.

Engine compartment wiring harness incorporate sev-

eral fusible links. Each link is identified with its gauge

size.
A fusible link is a length of special wire (normally

four wire gauges smaller than the circuit it is protecting)

used in wiring circuits that are not normally fused, such

as the ignition circuit. The same size wire with a spe-

cial hypalon insulation must be used when replacing a

fusible link.

The links are:

1.
The pigtail lead at the battery positive cable (except

Corvette) is a 14 gauge, brown fusible link protecting

the 10 gange battery charging circuit. This wire is

an integral part of the battery cable assembly and

servicing requires replacing the complete battery

cable assembly. On Corvette models this link is

installed as a molded splice at the solenoid "Bat"

terminal and servicing requires splicing in a new

link.

2.
A 16 gauge black fusible link is located at horn relay

to protect all unfused wiring of 12 gauge or larger.

It is a serviceable piece with an in-line connector

and is not integral with the wiring harness.

3.
The generator warning light and field circuitry (16

gauge wire) is protected by a fusible link (20 gauge

orange wire) used in the "battery feed to voltage

regulator #3 terminal" wire. The link is installed

as a molded splice in the generator and forward lamp

harness and is serviced by splicing in a new 20 gauge

wire as required.

4.
The ammeter circuit on all models is protected by

two orange, 20 gauge wire fusible links installed as

molded splices in the circuit at the junction block or

the solenoid "Bat" terminal (Corvette only) and at the

horn relay. Each link is serviced by splicing in a

new 20 gauge wire as required.

The wiring harnesses use a standarized. color code

common to all Chevrolet vehicles. Under the color code,

the color of the wire designates a particular circuit. The

harness title indicates the type of harness, single of mul-

tiple wire, and also describe the location of the harness.

The body harness is a flat, solid wire assembly and is

routed through the vehicle near the center of the body.

Composite wiring diagrams (figs. 104 thru 124) are in-

cluded at the end of this section.

MAINTENANCE AND ADJUSTMENTS

Maintenance of the lighting units and wiring system

consists of an occasional check to see that all wiring

connections are tight and clean, that the lighting units are

tightly mounted to provide good ground and that the head-

lamps are properly adjusted. Loose or corroded con-

nections may cause a discharged battery, difficult start-

ing, dim lights, and possible damage to generator and

regulator. Wire harnesses must be replaced if insulation

becomes burned, cracked, or deteriorated. Whenever it
is necessary to splice a wire or repair one that is bro-

ken, always use solder to bond the splice. Always use

rosin flux solder on electrical connections. Use insulat-

ing tape to cover all splices or bare wires.

When replacing wires, it is important that the correct

size be used. Never replace a wire with one of a smaller

size.

Each harness and wire must be held securely in place

by clips or other holding devices to prevent chafing or

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-8

is inserted through radiator support opening.

Remove two screws retaining lamp assembly to

lower sheet metal.

Remove three screws retaining lamp assembly to

lender.

To replace lamp assembly, reverse removal proce-

dure and check operation of the unit.
is aligned with flat on pivot shaft. Install stop lock

bolt and torque bolt to 45-60 in, lbs. Make sure that

side-to-side panel alignment is not changed when in-

stalling and tightening the stop.

CAUTION: Do not exceed specified torque

when tightening stop lock bolt.

HEADLAMP PANEL REPLACEMENT-CORVETTE

Refer to Figure 13 for Panel Mounting details.

1.
Remove engine compartment hood as outlined in

Section 1.

2.
Actuate headlamp panel to the open position.

NOTE:
In the event headlamp motor is inop-

erative, manual positioning of the panel can be

accomplished by turning the knurled knob at in-

board end of motor. As an assist in manual

operation of panel, apply light hand pressure to

panel in desired direction of rotation.

3.
Remove positive lead from battery terminal.

4.
Remove headlamp bezel retaining screws and bezel.

5. Remove the sealed beam housing unit as an assem-

bly - disconnect sealed beam leads at harness con-

nector and remove connector from sealed beam

leads;
remove the housing-to-panel retaining screws

and remove housing unit and wiring from panel.

6. Remove motor from panel pivot shaft - see motor

removal procedure. Then remove the panel stop

from panel inboard pivot shaft, and disconnect switch

lead wires from panel, support-mounted motor

switch.

7. Remove the panel retaining bolt access hole plugs

from inside the panel then rotate panel as required

and remove the retaining bolts and slide supports

from ends of panel pivot shaft. Remove bearing, felt

seal, retainer and washer from inboard pivot shaft.

8. Remove panel from its location by alternately disen-

gaging pivots from their retaining slots and with-

drawing unit forward through opening in body (fig.

14).

9. Loosen alien screw in spacer and disassemble parts

from the panel outboard pivot shaft.

10.
Install washer, retainer, felt seal, bearing and

spacer, in that order, to panel outboard pivot shaft.

Do not tighten spacer on shaft at this time.

11.
Position panel in body opening and index panel pivot

shafts in retaining slots; then loosely install support

retaining bolts.

12.
Install washer, retainer, felt seal, bearing and sup-

port, in that order, to panel inboard pivot shaft, and

loosely install support retaining bolts. -

13.
Check side-to-side alignment of panel, making sure

that there is no panel-to-body contact; position

spacer snugly against bearing; then tighten spacer

seat screw to 30-50 in. lbs.

14.
Install stop on panel inboard shaft so that it rests

against bearing, being sure that index mark on stop
15.
Check and align panel to body as follows:

a. Tighten panel pivot support bolts snugly but still

allowing panel to" be moved by applying hand

pressure.

b.
Position panel to the closed position and align

with body so that all surfaces are flush.

c. With the panel in the closed position the outboard

access hole is aligned with the forward bolt head.

Tighten this bolt with the panel in the closed

position - access to bolt head can be obtained by

working through opening between the hood and

body.

d. Rotate panel to obtain access to each bolt head

and torque bolts to 100-140 in. lbs.

e. Connect switch lead wires to support-mounted

limit switch.

16.
Install seaLed beam housing unit and at the same time

position sealed beam lead wires through panel out-

board pivot shaft. Install housing unit retaining

screws and install lead wires in connector, making

sure to match colors between harness and connector.

17.
Install motor assembly - see motor replacement

procedure.

18.
Connect positive lead to battery terminal.

19.
Adjust headlamp panel as outlined under "Headlamp

Panel Travel Adjustment".

20.
Adjust headlamp aiming as outlined under "Headlamp

Adjustment".

21.
Install headlamp bezel and engine compartment

hood - refer to Section 1 for hood installation.

Fig.
14
- Headlamp Panel Removal (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-9

Fig.
15 - Headlamp Panel Actuating Motor Mounting (Corvette)'

HEADLAMP PANEL MOTOR-CORVETTE (Fig. 15)

Removal

1.
Raise hood and as a safety precaution install a bolt

through the hole in the hood support - secure bolt

with a nut.

2.
Remove positive lead from battery terminal.

3.
Disconnect motor lead wire and position it out of the

way.

4.
Turn the knurled knob at inboard end of motor until

the gear seems to turrj freely - turn the knob in one

direction until a definite drag is experienced, then

rotate knob approximately six complete turns in the

opposite direction.

NOTE:
The above step is necessary to produce

a no-load condition on the drive gear and to per-

mit separation of motor from the panel pivot

shaft.

5. Remove the retainer from groove in motor locating

stud then remove the motor-to-support retaining

screw and remove motor assembly from the vehicle.

Installation

1.
Rotate motor and headlamp panel as required to align

slot in motor with headlamp panel pivot shaft, and

install motor on shaft so that the bracket is aligned

with the locating stud.

NOTE:
It may be necessary to turn knurled

knob on end of motor to permit alignment of

motor with shaft.
Slide motor onto shaft until it seats against shaft

shoulder; then install retainer in groove on locating

stud.

Install motor-to-support retaining screw making

sure ground wire is installed between screw head and

bracket.

Connect motor lead wires, making sure that contacts

are clean and that connection is secure.

Connect positive lead battery terminal, remove bolt

from hood support, close hood and check operation of

headlamp panel.

HEADLAMP MOTOR REPLACEMENT-

CAMARO (Fig. 16)

1.
Disconnect battery ground cable and when working on

right headlamp unit, remove battery from vehicle to

gain access to housing retaining bolts.

2.
Remove bezel retaining screws and bezel.

3.
Remove headlamp cover retaining screws and cover

from door assembly.

4.
Manually open door assembly (push door toward cen-

ter of vehicle) and disconnect limit switch

connections.

5. Remove four screws retaining assembly to radiator

support (note location and number of shims, if any).

6. Rotate assembly toward center of vehicle until rear

of unit is exposed, then disconnect wiring connectors

at headlamp and motor assemblies.

7. Rotate assembly until headlamp is facing downward

and carefully remove the assembly from the vehicle

opening.

8. Remove nut attaching motor assembly to pivot arm.

9. Remove two nuts and bolts retaining motor assembly

to base plate and remove motor assembly.

CHEVROLET CHASSIS SERVICE MANUAL