LIGHT SWITCH
LEFT TURN
INDICATOR BRIGHT BEAM INDICATOR RIGHT
TURN
INDICATOR
INSTRUMENTS
RADIO SPEAKER GLOVE BOX
LOCK
~~"-fHIf--RADIO
~~~~~~~&J CONTROLS
U:a~II---HEATER CONTROLS
INDICATOR REMAINING LlGHT~D DURING NORMAL OPERATION
TEMP-PRESS Indicator
PROBABLE CAUSE
Low Oil Pressure
Excessive Engi ne Oil Tem p.
GEN-FAN Indicator Generator Not Charging
Fan Not Operating
IMPORTANT:
ITEMS TO BE CHECKED
Engine Oil Level
Oil Level and Fan Belt
Generator
Fan Belt
If either of the indicators light during normal operation, STOP CAR IMMEDIATELY and turn off ignition. Check for a broken or slipping fan belt or low engine oil level. NEVER DRIVE CAR UNTIL BROKEN FAN BELT IS
REPLACED. Never drive car when "Temp-Press" indicator i s lighted. Car can be driven at slow speeds if only "GenFan" indicator is I ighted and fan belt is not broken, however, generator must be checked and serviced as soon as possi ble.
7
CONTROLS
LIGHT CONTROL KNOB
The three-position light switch is operated as shown.
Turn the
knob to vary the brightness of the instrument
lights. Turn fully counter-clockwise past the "detent" to
turn on the dome light.
TURN SIGNAL
The turn signal lever should be moved UP to signal
a right turn or DOWN to signal a left turn. The indicator
lights in the instrument panel will signal the direction as
will the parking and tail lights. When the turn is com
pleted, the lever will automatically return to neutral
position.
8
FULLY COUNTER CLOCKWISE TURN TO VARY OFF@ORDOMELIGHTSBRIGHTNESSOF ~ ~ /INSTRUMENT ___ -." , PANEL
~~~
/,;----;; .... , ~ LIGHTS J -1'-I' ...... ' // ..-.... ~, /)~/,.~ .. ·,' ~ /1/ -' I II I" J/::::,'/·~"·I;'·""\ 1\1-~.P~ ~ \11 I" I'
/
-'-"'~\\ ,,/ ~ ... "., ~~-, ..... '1' ~~ .... "-'--INSTRUMENT ~-""-PARKING AND TAIL "-LIGHTS LIGHTS HEADLIGHTS
DIMMER SWITCH
The foot button located near your left foot switches
the
headlights between "high" and "low" beam. The
"high" beam indicator, located in the center of the
speedometer dial, will be lighted when the headlights
are on "high" beam. Always dim the lights when ap
proaching oncoming cars.
. I CLUTCH PEDAL
,,~~:U
BULB SPECIFICATIONS Candle Power
Headlamp Unit-Outer: High Beam. 37 V2 W
Low Beam. . 50 W
Inner: High Beam.
Parking
Lamp and Directional Signal
Tail and Stop and Turn Signal Lamps
Back -up Lamp .... ....... .... .
Instrument Lamps ............. .
Direction
Signal Indicator Lamp .. .
Temperature-Pressure Indicator
Lamp
Generator-Fan Indicator Lamp ....
Headlamp High Beam Indicator Lamp
Ignition Lock Lamp ............ .
Glove Compartment
Lamp .... .. .
Dome Lamp ............. .. .. .
Courtesy
Lamp . .............. .
License Plate Lamp ........... .
Radio Dial
Lamp ............. .
Heater Control
Panel Lamp ..... .
FUSES AND CIRCUIT BREAKER
37%
4-32
4-32
32
3 2
2
2
1
1
2 15
6 4
2
1
Number
4002
(Sealed
Beam)
4001
(Sealed
Beam)
1034
1034 1073
GE 1816
53
57
57
53 53
57 211
89
67 1891
53
A
circuit breaker in the light control switch protects
the headlamp circuit, thus eliminating one fuse. Where
29
current load is too heavy, the circuit breaker rapidly
opens and closes, protecting the circuit until the cause
is found and eliminated.
Fuses,
located in the Junction Block beneath the
dash are:
1 . Heate r Blower
Glove Compartment
Lamp ........ 3AG/ AGC-l 0 amp.
2. Tail and Stop Lamps,
Direct ion Signals ................ 3AG/ AGC-l 0 amp ..
l. Heater (Total System)
Back-up Lamp . ........ ......... lAG/ AGC-20 amp .
4. Radio ..
......... ...... ........ lAG/ AGC-4 amp.
5. Instrument
Panel Lamps
Radio Panel Lamp
Heater Control Panel Lamp ... ...... 3AG/ AGC-3 amp.
FUSE BLOCK
