1953 JEEP CJ wheel bolts

H

ELECTRICAL
SYSTEM
sibility
of the cable shorting at the
engine
or frame.
Remove nut and lock washer securing the ignition

wire
to the solenoid
post
and remove the two screws and lock washers securing the solenoid to
the starter frame. Remove the switch,
b.
To install the solenoid switch reverse the re­

moval
procedure given above.

H-10S.
STARTING MOTOR
—
DELCO
DAUNTLESS
V-6
ENGINE

Refer
to Fig. H-45.

The
starting motor used on the Dauntless V-6 en­

gine
has an integral solenoid switch and enclosed
shift lever which first shifts the overrunning clutch
pinion into
engagement
with the ring gear on the
flywheel of the
engine
and then
closes
the electrical
circuit
to cause
engine
cranking. When the
engine

starts,
the overrunning clutch
disengages
to pre­ vent transfer of
engine
speed to the starting motor.

Note:
Should a service replacement starter motor
be required the factory recommends replacement

with
original equipment parts; however, should the need arise an existing starter motor (Delco or
Prestolite) could be replaced with the current
Delco-Remy
starter, model 1108375, with the
following modifications to the wiring harness. If
the existing starter motor wiring harness
does
not
provide a 12 ga. purple conduit wire, (connects the ignition switch to the starter motor) then a 12 ga.

purple
conduit wire 70 inches long, must be in­

stalled.
Should the existing starter motor wiring
harness
contain a 16 ga. light blue conduit wire, (connects the ignition switch and starter motor)
bend this wire back and tape out of the way.

H-109.
Starting Motor Disassembly
a.
Before removing the starting motor from the
engine, disconnect leads and cover battery lead

terminal
with piece of
hose
or tape to prevent
short circuiting.
Note
locations of wiring connec­
tions to assure proper reconnection. Remove the cap screw that secures the starting motor to the
angle bracket on the side of the engine. Remove
the two cap screws that secure the drive end of
the starting motor to the cylinder block; remove
the starting motor.

b.
Remove terminal nut and disconnect field lead,

which
passes through grommet at top of motor,
from
motor terminal of solenoid. Remove two
thru

bolts
from motor. Remove commutator end frame

and
field frame assembly from solenoid and drive assembly.
e.
Pull
out pivot pins of brush holders and remove each of two brush holder and spring assemblies

from
field housing. Remove screws which attach
brushes and leads to holders.

d.
Remove armature and drive assembly from
drive
housing. Remove thrust collar from pinion
end of armature shaft. Remove leather thrust

washer
from
opposite
end of shaft.
e. To separate drive assembly from
armature,
place

a
metal cylinder of proper size (J^" [12,7 mm.]
pipe coupling is satisfactory) over end of armature
shaft to bear against the pinion
stop
retainer. Tap
retainer
toward armature to
expose
snap ring as
shown in
Fig.
H-47. Remove snap ring from
groove
in
shaft; slide retainer and pinion drive assembly

from
shaft. Remove assist spring from shaft,

f.
Remove two screws holding solenoid switch to
drive
housing remove switch. Remove small nut

and
insulating washer from the solenoid S terminal.
Remove nut and insulating washer from the
sole­

noid battery (large) terminal. Remove two screws that attach switch cover to solenoid and remove cover for inspection of switch parts. Remove shift
lever fulcrum bolt and remove shift lever, plunger,

and
return spring.
12765
FIG.
H-47—REMOVING PINION
DRIVE
ASSEMBLY

FROM
ARMATURE SHAFT

1— XA ' Pipe Coupling

2—
Snap
Ring
and Retainer

3—
Armature
Shaft
4—
Drive
Assembly
H-110.
Starting
Motor
Cleaning and
Inspection

a.
Wipe all parts clean with clean cloths. The
arma­
ture,
field coils, and drive assembly must not be
cleaned by any degreasing or high temperature
method.
This
might damage insulation so that a
short
circuit
or ground would subsequently develop.
It
would also remove lubricant originally packed

in
the overrunning clutch so that clutch would

soon
be ruined.

b.
Carefully
inspect all parts visually for wear or
damage. Make necessary repairs or replace unserv­
iceable parts. Any soldering must be
done
with

rosin
flux.

Note:
Never use acid flux when solding any elec­

trical
connections and never use emery cloth to
clean
armature
commutator or other
electrical
units. 208

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

The
correct distance should be 10%"
[26,04
cm.].

If
the length of the clutch release pedal rod is
other than
10
W
[26,04
cm.], the vheicle is equipped with the early
type
Clutch
Control
Lever

and
Tube Assembly, which should be removed, and^trie latest
designed
parts should be installed.

The
free pedal clearance is adjusted by lengthening
or shortening the" clutch fork cable. To make this adjustment,
loosen
the jam nut on the cable clevis

and
lengthen or shorten the cable to obtain %"
[19,05
mm.] free travel at the pedal pad, then
tighten the jam unit.
•
Clutch
Control Cable Type

Refer
to Fig. 1-2.

a.
With the clutch pedal pad against the floor
panel, (pedal up, clutch
engaged)
adjust ball ad­
justing nut until slack is removed from the cable
and
the clutch throwout bearing contacts the clutch
pressure plate, release levers or diaphragm plate.
b. Back-off ball adjusting nut 2
V2
turns to obtain
approximately %"
[19,05
mm.] free travel.
Lock

hex nut.
FIG.

1-3—AUBURN
CLUTCH
ASSEMBLY —
HURRICANE F4 ENGINE 1—
Driven
Plate and Hub
2—
Pressure
Plate

3—
Pivot Pin
4—
Bracket
5—
Spring
Cup 6—
Pressure
Spring 7— Release
Lever

8—
Return
Spring
9—
Adjusting
Screw
10—
Jam
Nut 11—
Washer
Note:
Some older 'Jeep' vehicles may
develop
side

movement
of the clutch and brake pedals resulting
from wear of the pedals, shafts, and bushings. One way to
compensate
for this wear is to install a pedal

slack
adjuster kit 1-4.
CLUTCH
—
HURRICANE
F4
ENGINE
•
Auburn
Vehicles equipped with the Hurricane F4
engine

have a 9.25" [23,4 cm.] driven plate. The auburn clutch driving (pressure) plate assembly (Fig. 1-3)
has three pressure springs and three levers or
fingers.
1-5.
Clutch
Removal

When
necessary to remove the clutch,
follow
the procedures outlined in Section J for the removal
of the transmission and transfer case from the vehicle. Then remove the flywheel housing and use
the following procedures for removing the clutch assembly.

Note:
The F4
engine
may be removed from the
vehicle when inspecting or replacing the clutch.
Refer
to Section D for Hurricane F4
engine
re­moval and then
follow
the instructions given
below

to remove the clutch assembly.

a.
Mark
the clutch pressure plate and
engine
fly­
wheel with a center punch so the clutch assembly
may be installed in the same position after adjust­

ments
or replacement are completed.
b. Remove the clutch pressure plate bracket
bolts

equally, a little at a time, to prevent distortion and
to relieve the clutch springs evenly.
c. Remove the pressure plate assembly and driven
plate from the flywheel.
1-6.
Clutch
Pressure Plate and Disc Inspection
Inspect the pressure plate face for
cracks,
chips,

and
warpage.
Check
the pressure plate levers for
excessive
wear and the springs for breaks. If any of the
above
conditions exist, the
complete
pressure
plate must be replaced.
Check
the clutch disc for

excessive
wear,
loose
or damaged facings, broken
vibration damper springs and evidence of grease
or oil. If any of the
above
conditions exist, replace
the clutch disc.
1-7.
Clutch
Pressure Plate Adjustment —
Auburn
The
clutch pressure plate must be checked
before
installing a new or reconditioned clutch. The proper 11339

FIG.
1-4—CHECKING
AUBURN
CLUTCH
LEVER
ADJUSTMENT
1— Adjustment Gauge
2—
Fixture
Mounting Bolt

3—
Clutch
Fixture
227

CLUTCH

©—*

11378

FIG.
1-5—ADJUSTING
AUBURN
CLUTCH
LEVERS

1—
Gauge
5—Mounting Bolt

2—
Clutch
Lever
6—Clutch
Pressure
Plate

3—
Adjusting
Screw
7—Thickness
Spacer

4—
Locknut
8—Clutch
Adjusting
Fixture
spacer thickness and
gauge
length is listed in

Par.
1-30. Use
Clutch
Adjusting Fixture W-296
and
proceed as follows:

a.
Place the thickness spacers
between
the pressure
plate face and clutch adjusting fixture. Locate the spacers under the pressure plate levers and at the
center of the pressure plate face, see Fig. 1-5.
b. With the spacers properly installed, bolt the
pressure plate to the adjusting fixture.
Draw
the

bolts
down evenly a little at a time until they are
tight.
c. Using the proper
gauge
length check the lever adjustment as shown in Fig. 1-4.

d.
Lever
adjustment can be altered by removing
the lever clips, loosening the locknut and turning
the adjusting screw (Fig. 1-5) in or out as required.
FIG.
1-6—REMOVING
PILOT
BUSHING
1—
Flywheel

2—
Pilot
Bushing

3—
Pilot
Bushing Remover 1-8. Pilot Bushing Inspection and Replacement

•
F4 and V-6 Engine.
Inspect the transmission main shaft pilot bushing

which
is pressed into the center of the flywheel on
the Hurricane F4
engine
and in the center of the
crankshaft
on the Dauntless V-6 engine. If the bushing is worn or damaged, it should be removed,
using a pilot bushing remover. Screw the tapered end of the tool into the damaged bushing, allowing
the tool to cut its own threads until a solid grip is obtained. Insert the puller screw and rotate it
until
bushing is forced out of flywheel, Fig. 1-6 or

crankshaft.

To
install a new bushing, slide the bushing
onto

the end of a pilot bushing installing and burnishing tool and insert the bushing into flywheel or
crank­
shaft. A
soft
hammer can be used against the tool
to help drive the bushing in place. When the tool
is removed (by tightening the cap and pressure
nut as shown in Fig. 1-7), the bushing
will
be
burnished
to correct size. Apply a small amount of

lubricant
to the bushing bore.
FIG.
1-7—INSTALLING
PILOT
BUSHING
1—
Pilot
Bushing
Installing
and
Burnishing
Tool

2—
Flywheel
1-9.
Clutch
Installation

a.
Inspect
Clutch
Disc
Before the clutch disc is installed, it should be
carefully
inspected for warpage. If grease or oil is evident on the friction facings, the facings should
be replaced and the cause of oil accumulation cor­ rected. Excessively worn facings should also be
replaced with factory recommended parts.
b. Inspect
Clutch
Release Bearing and Sleeve

The
clutch release bearing and
sleeve
are attached to the front facing of the transmission case by a

spring.
Check
the bearing and
sleeve
for evidence
of grease leaks from within the bearing or for wear

and
looseness.
Replace parts as necessary. 228

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

I
Note:
The clutch release bearing is lubricated at
time of assembly and no attempt should be made
to lubricate it Refer to Fig. 1-23 when lubricating
the clutch throwout bearing collar. c. Reassembly

To
assemble the clutch to the flywheel, first put
a
small amount of light cup grease in the flywheel
pilot bushing, install the driven plate, with short
end of hub toward the flywheel, then place the pressure plate assembly in position.
With
a clutch
plate aligning arbor or a spare transmission main
shaft, align the driven plate splines leaving the
arbor
in position while tightening the pressure plate
screws evenly.
Next, assemble the flywheel housing to the
engine
and
reinstall the transmission and transfer case or
install
the
engine
in the vehicle, depending on the
procedure of removal. Make sure that the clutch
release bearing
carrier
return spring is hooked in place. For the remainder of the assembly reverse
the operations that were used in removing the
transmission and transfer case or the
engine
referring
to the instructions given in Section J for the transmission and Section D and Dl for the
engine.

d.
Adjust the clutch control cable so there is 3A" [19,05 mm.] free pedal travel. (Refer to Par. 1-3)

1-10.
CLUTCH
—
DAUNTLESS
V-6
ENGINE
•
Diaphragm Spring Type
(Early
Models)

*
Jeep' vehicles equipped with a Dauntless V-6 en­
gine
use a 10.4" [26,4 cm.] single-plate, dry-disc

clutch,
incorporating a diaphragm-type spring as­
sembly.

When
the clutch pedal is depressed, it
moves
the
clutch
fork in the direction shown in Fig. 1-8. The

clutch
fork, pivoting on a
ball
stud, acts upon the
throwout bearing. The bearing then forces the
prongs of the diaphragm spring in the direction shown in
Fig.
1-8. The diaphragm spring is mounted
so that it pivots on its retaining rings.
This
reverses
the direction of force.
Force
is applied directly to
the three retracting springs which then
move
the
pressure plate
rearward,
away from the driven plate.

The
clutch driven plate assembly slides freely on
the transmission main drive gear splined shaft. It is keyed to the gear shaft by ten splines. The
front end of the main drive gear shaft is piloted by a bushing pressed into a recess in the
rear
end
of the
engine
crankshaft. See Fig. 1-8.

The
outer area of the driven plate is divided into

segments
formed in low waves to provide springs

between
the plate facings and cushion
engagement

of the clutch. A molded facing is riveted to each
side of every
segment.
When the clutch is fully
released, the waved
segments
cause the facings to

spread
approximately .045" [1,14 mm.]. Pressure
plate movement provides an additional clearance
of approximately .030" [0.76 mm.] to assure
full
release of the driven plate. See Fig. 1-8.

The
driven plate assembly is designed to prevent
torsional fluctuation of the
engine
from being
transmitted to the transmission gears. Its hub is
FIG.
1-8—CLUTCH
RELEASE
ACTION

1—
Pressure
Plate 5—Engine
Crankshaft

2—
Throwout
Bearing
6—Pilot
Bearing

3—
Pivot
Point
7—Flywheel

4—
Clutch
Fork
8—Driven
Plate
driven
through torsional coil springs; additional

frictional
dampening is supplied by molded
fric-

tional washers.

1-11.
Clutch
Removal

a.
Remove transmission as described in Section J. b. Remove clutch throwout bearing and pedal re­

turn
spring from clutch fork.
c. Remove flvwheel housing from engine.
d.
Disconnect clutch fork from
ball
stud by forc­
ing it toward the center of the vehicle.
e.
Mark
clutch cover and flywheel with a center

punch
so that cover can later be installed in the same position on the flywheel.
This
is necessary to

maintain
engine
balance.
f. Loosen the clutch attaching
bolts
alternately,
one
turn
at a time, to avoid distorting the clutch
cover flange, until diaphragm spring is released.
g. Support the pressure plate and cover assembly
while removing last bolts; remove pressure plate
and
driven plate from flywheel.

Caution:
Use extreme care to keep clutch driven plate clean.

h.
If it is necessary to disassemble pressure plate,
remove three drive strap-to-pressure plate
bolts
and
retracting springs. Remove pressure plate from

clutch
cover.

Note:
When disassembling,
note
position of
grooves

on
edge
of pressure plate and cover. These marks must be aligned in assembly to maintain balance.

i.
The clutch diaphragm spring and two pivot rings

are
riveted to the clutch cover. Inspect spring, rings

and
cover for excessive wear or damage. If there
is a
defect,
replace the complete cover assembly.

1-12.
Clutch
inspection

Wash
all metal parts of clutch, except release bear­
ing and driven plate, in suitable cleaning solution to remove
dirt
and grease. If solvent
seeps
into

bearing,
lubricant may be dissolved. Cleaning sol­
vent
will
also damage the facings of driven plate,
a.
Inspect friction surfaces of flywheel and pres­

sure
plate for scoring or roughness. Slight roughness
may be smoothed with fine emery cloth. If surface 229

CLUTCH

is deeply scored or grooved, the part should be

replaced.

b. Inspect driven plate for wear or damage to fac­
ings,
loose
rivets, broken or
loose
torsion springs,

and
flattened cushion springs. If facings are worn
near
rivets or are oily, replace the plate assembly.

A
slight amount of oil on clutch facings
will
cause

clutch
grab and chatter; excessive oil on facings

will
cause slippage. It is not practical to remove
oil
with solvents or by buffing since oil
will
con­
tinue to bleed from facing material when hot. If
oil
is found on driven plate facings, examine trans­
mission drainback hole, pilot bushing,
engine
rear

main
bearing and other points of possible oil leakage. Test the fit of driven plate hub on trans­
mission main drive gear for an easy sliding fit.
c. Inspect clutch release bearing for scoring or ex­ cessive wear on front contact face. Test for rough­

ness
of balls and races by pressing and turning
front race slowly. Inspect main drive gear pilot
bushing in crankshaft. Replace bushing if it is rough or worn. Regardless of whether the old plate

or
a new plate is to be installed, check the plate
for runout. Slide the driven plate, front side first,
over the transmission main drive gear shaft so that

it
is tight on the spline. Index a
dial
indicator to the plate facing as shown in
Fig.
1-9. While holding

firmly
against front end of main drive gear, to take up play in main drive gear bearing, slowly
rotate driven plate and observe the amount of
run­

out shown by indicator. If runout of front facing
exceeds
.025" [0,635 mm.], replace the plate. It
is not practical to correct excessive runout by bending. 12769

FIG.
1-9—RUNOUT
CHECK
—
CLUTCH
PLATE
1—
Front
Facing
(Flywheel
Side)

2—
Dial
Indicator
Set
d.
Check
clutch pilot bushing for excessive wear

or
damage. Replace pilot bushing, if necessary, with

special
removal and installation
tools.
(See
Figs.

1-6 and 1-7). 1-13.
SERVICING
CLUTCH
PRESSURE
PLATE
AND

DISC
—
BORG
&
BECK
V6
(Late
Models)

The
Borg & Beck clutch is a single plate, dry disk
type. It provides smooth
engagement
of
engine
power to the wheels. The clutch consists of a pres­

sure
plate assembly with pressure springs and
release levers, and driven plate assembly. The
driven
plate assembly
uses
spring center vibration
neutralizes and two flexible facings.

The
clutch driven plate is spring cushioned with a facing riveted to both sides. The coil springs around
the hub absorb the power shocks and cushion the

driving
mechanism. The clutch throw-out bearing is of the
ball
type, packed at time of manufacture,

and
requires no further lubrication.
No adjustment for wear is provided in the clutch itself. An individual adjustment is built into the
clutch
cover to adjust the height of the release
levers.
This
adjusting nut is locked in position

and
should never be disturbed unless the clutch assembly has been disassembled for the replace­
ment of worn parts or to correct the height of the release levers.

When
the clutch pedal is depressed (disengaged),
the release bearing is moved toward the flywheel
and
contacts the inner ends of the release levers.

Each
lever is pivoted on a floating pin which re­
mains stationary in the lever and rolls across a short flat portion of the enlarged
hole
in the eye-
bolt. The outer ends of the
eyebolts
extend
through
holes
in the stamped cover and are fitted

with
adjusting nuts to secure the levers in the
correct
position. The outer ends of the release levers

engage
the pressure plate lugs by means of ful-
crums,
which provide knife-edge contact
between

the outer ends of the levers and the lugs as shown
in
Fig.
I-10. 12190

FIG.
MO—CLUTCH
LEVER
POSITIONS
A—Clutch
Engaged
B—Clutch
Disengaged 1-14.
Clutch
Pressure Plate Adjustment

The
clutch pressure plate adjustment must be
checked before installing a new or reconditioned

clutch.
The proper spacer thickness and
gage
length for a particular clutch is listed in Par. 1-30.
Use
Clutch
Adjusting
Fixture
W-296. If the W-296
fixture is not available one can be fabricated as
described in Par. 1-26. 230

'Jeep*
UNIVERSAL SERIES
SERVICE
MANUAL
b.
Check
the anti-rattle springs in the clutch cover

and
place the cover on top of the pressure plate
assembly. The top of each pressure spring must enter its spring seat in the cover.
Line
up punch

marks
on cover and pressure plate for balance.

c.
Slowly compress the cover making sure that
the
eyebolts
and pressure plate lugs are guided through the proper
holes
in the cover.

d.
Hold the clutch under compression and screw
down the adjusting nuts until they are flush with
the
tops
of the eyebolts. Release the spindle of
the press.

1-24.
Clutch
Lever Adjustment

Important:
Always inspect release lever height
adjustment when installing a new clutch drive
plate.

Place
a clutch
gauge
plate on the flywheel in the
position normally occupied by the driven plate.
FIG.
1-16—CLUTCH WITH GAUGE
PLATE

1—Machined
Land
2—Gauge Plate

FIG.
1-17—CHECKING
LEVERS
FOR
FREE
MOVEMENT
Mount
the cover assembly, center the plate and
line up the three machined lands on the
gauge

plate directly under the levers, as shown in
Fig.
1-16.
Tighten
the cover screws in rotation, one to two

turns
at a time, to avoid distortion of the cover.
FIG.
1-18—CLUTCH HEIGHT ADJUSTMENT
Each
lever should be depressed several times be­
fore checking.
This
will
seat the levers in their operating positions, as shown in Fig. 1-17.
Place
the
gauge
on the hub as shown in Fig. 1-18.

To
adjust the levers,
turn
the lever adjustment nut until the levers are
%{'
to %6" [0,93 a 1,59 mm.]
above the hub. Before staking the adjusting nuts
to lock them in place, work the lever up and down
and
recheck lever adjustment again. Stake the nut with a
dull
punch, as shown in Fig. 1-19.
FIG.
1-19—LOCKING ADJUSTING NUTS

1-25.
Clutch Throwout
Release Bearing

The
clutch throwout or release mechanism consists
of a forked lever which pivots on a
ball
pivot threaded into the clutch housing. A throwout lever

return
spring is anchored to a clip under the
ball

pivot and holds the lever in contact with the
ball

pivot. The clutch throwout bearing, which is a
pre-lubricated
unit, is attached to the forked end of the throwout lever.
Never wash the clutch throwout release bearing in
gasoline or any solvent that
will
dissolve the
lubri­

cant.
It is neither necessary nor possible to
lubri­

cate this bearing at any time. Connect linkage
to the throwout release lever. Adjust free-play as

directed
in Par. 1-3. 233

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

I thickness: .285"
[0,724
cm.], .305"
[0,775
cm.].

Each
spacer should be hardened and ground to size, and then have the dimensional thickness
stamped thereon.

c.
From
flat bar stock at least Vfe" [3 mm.] thick,
make a
gauge
as shown in Fig. 1-22. Harden, grind
to size, and stamp sizes on the
gauge.

1-27.
Clutch Installation

a.
Very
sparingly, apply wheel bearing lubricant
to inner surface of pilot bushing in crankshaft.

Caution:
If
excessive
lubricant is applied to pilot bushing, it
will
run out on face of flywheel when
hot and
ruin
the driven plate facings.
b. Make sure that splines in the driven plate hub
are
clean; apply a light coat of lubricant to splines
of hub and transmission drive gear shaft. Slide plate over gear shaft several times; remove plate
from shaft and wipe off
excess
lubricant.

Caution:
Driven plate facings must be kept clean

and
dry.

c.
Fill
groove
in throwout bearing collar with wheel bearing lubricant. See Fig. 1-23. Make sure
that front bearing retainer of transmission is clean;
apply a light coat of wheel bearing lubricant. Slide
throwout bearing over bearing retainer several times. Remove bearing from retainer and wipe off

excess
lubricant.

12736
FIG.
1-23—LUBRICATION
POINTS
—

CLUTCH
THROWOUT
BEARING
COLLAR

1—Coat
This
Groove 2—Pack
This
Recess
d.
Clean
and apply wheel bearing lubricant to ball
stud in flywheel housing and to the
seat
in clutch

fork.

e.
If disassembled, install pressure plate in the cover assembly, lining up the
groove
on its
edge

with the
groove
on the
edge
of the cover.
Install

pressure plate retracting springs, and the three
drive
strap-to-pressure plate
bolts
and lock washers.

Torque
bolts
11 lb-ft. [1,51 kg-m.].

Note:
The diaphragm
type
clutch assembly is fac­
tory calibrated and requires no adjustment
before
installation. Refer to Par. 1-14 to adjust Borg and

Beck
coil spring
type
clutch assembly.
f.
Install
the pressure plate and driven plate on
flywheel. Support both assemblies with a spare
main
drive gear.

Note:
Be certain that
mark
on clutch cover is
aligned with the
mark
made on the flywheel during
clutch removal.
g.
Install
clutch attaching
bolts
and tighten alter­ nately so that clutch is drawn squarely
into
position
on flywheel.
Each
bolt
must be
tightened
one turn at a time to avoid bending the clutch cover flange.

Torque
bolts
30 to 40 lb-ft. [4,1 a 5,5 kg-m.].

h.
Lubricate
the ball stud and clutch fork with
wheel bearing lubricant and install clutch fork.

Note:
Be certain that fork retaining spring is
tight

on pivot ball stud.

i.
Install
flywheel housing on
engine
cylinder
block.

Caution:
Be certain that dowel pins are installed

in
cylinder block.

j.
Lubricate
the recess on the inside of the throw-
out bearing collar. Be careful not to use too much
lubricant.
See Fig. 1-23.

Caution:
Make certain that the lips of the spring
retainer (attached to the clutch fork) are in
groove
of the bearing. See Fig. 1-24.
k.
Install
throwout bearing assembly and connect
clutch linkage.
I.
Install
transmission as described in Section J. m. Adjust clutch for %"
[19,05
mm.] free travel,
see
Par.
1-3. 235

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

J

10489

FIG.
J-2—THREE-SPEED
TRANSMISSION
— T90 1—
Main
Drive
Gear

2—
Main
Drive
Gear
Bearing
Retainer

3—
Main
Drive
Gear
Bearing
Retainer Oil
Seal
4—
Main
Drive
Gear
Snap
Ring

5—
Main
Drive
Gear
Bearing
Snap
Ring

6—
Main
Drive
Gear
Bearing
7—
Synchronizer
Shifting Plate
8—
Shift
Rail
Cap
9—
Shift
Rail—High
and Intermediate
10—
Shift
Rail
Poppet
Ball

11—
Shift
Rail
Poppet
Spring

12—
Shift
Fork—High
and Intermediate

13—
Control
Housing
14—
Control
Lever
Support
Spring

15—
Control
Lever
Housing Pin
16—
Control
Lever
Fulcrum
Ball

17—
Gear
Shift
Lever
18—
Shift
Fork—Low
and Reverse

19—
Sliding
Gear—Low
and Reverse
20—
Main
Shaft
Bearing
Adapter

21—
Main
Shaft
Bearing
22—
Main
Shaft
Washer

23—
Main
Shaft Nut
24—
Main
Shaft

25—
Idler
and Countershaft
Lock
Plate
26—
^Countershaft
Gear
Bearing
Rollers

2
7—Countershaft

28—
Countershaft
Thrust
Washer
Rear—Steel

29—
Countershaft
Thrust
Washer
Rear—Bronze

30—
Countershaft
Gears
31—
Transmission
Case

32—
Main
Shaft Second Speed
Gear
33—
Countershaft
Bearing
Spacer
34—
Synchronizer
Blocking
Ring

35—
Countershaft
Thrust
Washer
Front—Bronze

36—
Countershaft
Bearing
Washer

37—
Intermediate
and High Speed
Clutch
Sleeve

38—
Intermediate
and High
Clutch
Hub

39—
Synchronizer
Spring

40—
Intermediate
and High
Clutch
Hub
Snap
Ring

41—
Main
Shaft Pilot
Bearing
Roller

CJ-5A,
CJ-6A
models, remove the remote control

rods.

d.
Remove the set screw from the transfer case
shift lever pivot pin. Remove the pivot pin, shift

levers,
and shift lever springs. On models
CJ-5A,
and
CJ-6A
remove pivot pin cotter key and the

adjusting
rod attaching nut to remove shift lever.
See
Fig.
J-l.

e. If the vehicle is equipped with power take-off,
remove the shift lever plate screws and lift out the

lever.

f. Disconnect the front and
rear
propeller shafts
from
the transfer case, following the procedure de­

tailed
in Section
L.
Should the vehicle be equipped

with
power take-off, disconnect the transfer case end of the power take-off drive shaft.
g. Disconnect the
speedometer
cable at the transfer case.

h.
Disconnect the hand brake cable.
i.
Disconnect the clutch release cable at beilcrank
yoke end.
j.
Place
jacks
under the transmission and engine,
protecting the
engine
oil pan with a block of wood,
k.
Remove the nuts holding
rear
mounting to

frame
cross member.

I.
Remove the transfer case snubbing rubber bolt
nut at cross member.

m.
Remove
bolts
holding frame center cross mem­

ber
to frame side
rail
and remove cross member,
n.
Remove
bolts
holding transmission to flywheel
bellhousing.
o.
Force
transmission to right to
disengage
clutch
control
lever tube
ball
joint.

p.
Lower
jacks
under
engine
and transmission.

Slide
transmission and transfer case assemblies

toward
rear
of vehicle until the clutch shaft clears the flywheel housing.
q.
Lower
jack
under transmission. Remove trans­ mission and transfer case as an assembly from

under
the vehicle.

r.
For separation of the transmission and transfer
case, refer to Par. J-7. 241