1953 JEEP CJ fuel type

light seat adjustment hood open window recommended oil wheel bolts

Page 211 of 376

JEEP CJ 1953 Service Manual
Jeep
UNIVERSAL
SERIES SERVICE
MANUAL

H
Note:
Pinion clearance cannot be adjusted. If
clearance is not correct, motor must be disassem
bled and checked for the above mentioned defects.

A

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

H
Note:
Pinion clearance cannot be adjusted. If
clearance is not correct, motor must be disassem
bled and checked for the above mentioned defects.

Any
defective parts must be replaced.
H-118. Starting Motor Test —
Genera!

To
obtain
full
performance data on a starting motor, or to determine the cause of abnormal
operation, the motor should be submitted to no-
load and locked armature
tests,
with equipment designed for such
tests.
A high-current variable resistance is required to obtain the specified volt
age at the starting motor.
This
is necessary since
a
small variation in the
voltage
will
produce a
marked
difference in the current
drawn.

H-119.
Starting Motor No-Load Test

This
test
requires a DC voltmeter capable of
read

ing
voltages
in a 12-volt
circuit,
a DC ammeter

with
maximum range of several hundred amperes,
a
high-current variable resistance, an rpm. in

dicator,
and a fully-charged, 12-volt battery.

a.
Connect a jumper lead
between
S terminal
and
large battery terminal of starter solenoid.
Con
nect voltmeter
between
either of
these
terminals (positive) and motor frame (negative, ground).

Connect
ammeter and variable resistance in series

between
positive terminal of battery and battery

terminal
of solenoid. Set up rpm. indicator to show starting motor speed.
b.
Initially,
adjust variable resistance to a value of
approximately .25 ohm. To complete the
circuit,

connect negative terminal of battery to motor

frame.
Adjust variable resistance to obtain a volt meter reading of 10.6 volts;
note
speed of starting motor and ammeter reading. Motor speed should
be
6750
to
10,500
rpm.; ammeter reading should
be 50 to 80 amperes.
c. Rated speed and current indicate normal condi
tion of the starting motor. Low speed and high
cur
rent
may show friction; this could be caused by
tight, dirty, or worn bearings, bent armature shaft,

or
a
loose
field
pole
shoe
dragging against the

armature.
It could also be caused by a short-cir cuited armature, or by grounded armature or field
coils.

d.
Failure
to operate and high current indicates

a
direct short circuit to ground at either the battery

terminal
or field coils.
e.
Failure
to operate and no current are usually
caused by broken brush springs, worn brushes, high insulation
between
commutator
bars,
or
some
other
condition preventing
good
contact
between
the brushes and commutator. It can also be caused by
open circuit in either the field coils or armature coils.
f. Low speed and low current show high resistance due to poor connections, defective leads, dirty com
mutator, or one of the conditions mentioned in e,
above.
g. High speed and high current indicates a short
circuit
in the field coils. H-120-
Locked
Armature Test

This
test
requires a DC voltmeter with range ap

propriate
to read
voltages
in a 12-volt
circuit,
a DC
ammeter with maximum range of several hundred
amperes, a high-current variable resistance, a
clamping fixture to lock
together
the motor shaft

and
case, and a fully-charged 12-volt battery.

a.
Connect a jumper lead
between
S terminal and
large battery terminal of starter solenoid. Connect
voltmeter
between
either of
these
terminals (posi
tive) and motor frame (negative, ground). Connect
ammeter and variable resistance in series
between
positive terminal of battery and battery terminal
of solenoid.
Install
clamping fixture to lock motor
shaft and case
together
securely.
b.
Initially,
adjust variable resistance to approxi
mately .05 ohm. To complete the
circuit,
connect
negative terminal of battery to motor frame. Ad

just
variable resistance to obtain a voltmeter
read
ing of 4.0 volts. Ammeter reading should be 280
to 320 amperes.

H-121.
Solenoid Starter Switch — Delco

The
solenoid-type switch is mounted directly on
the starting motor.
This
type of switch is energized
by turning the ignition key to the extreme right position. Should the solenoid switch
fail
in service

it
is necessary to install a new assembly.

Should
a starting motor
fail
to deliver maximum power the fault may be due to
voltage
drop at the

starter
switch contacts due to corrosion or burning.

Check
the switch by comparing the
voltage
at the
battery across the terminals. The
voltage
drop
should not exceed .05 volts per 100 amperes.
In
order to remove the starter solenoid, it is neces

sary
to remove the starter assembly.

H-122.
ELECTRICAL
INSTRUMENTS

H-123.
Fuel
Gauge —
CJ-3B

The
fuel
gauge
circuit is composed of the indicating

unit,
mounted on the instrument panel, and the
fuel tank unit, connected by a single wire through the ignition switch.

Should
the
gauge
fail
to register, check all wire con nections to be sure they are tight and clean; also
be sure both units are well grounded. If, after this
check, the
gauge
does
not indicate properly, remove
the wire from the tank unit and connect it to a
new tank unit which must be grounded to the tank

or
frame for
test.
Turn
the ignition switch "ON"
and
move
the float arm through its range of travel,
watching the dash unit to determine if it indicates
correctly.
If it fails to do so the trouble is probably

in
the dash unit and it should be replaced.

Should
a new tank unit be unavailable for this
test,
disconnect tank unit wire at the instrument panel

gauge.
Connect one lead of a 12 V, 1 CP
test
light
to the instrument panel unit terminal and with the
ignition switch
"ON"
ground the other lead. If the
unit is operating correctly the pointer
will
move

approximately three-quarter across the
dial.
Do not attempt to repair either unit; replacement
is the only precedure. 211

Page 212 of 376

JEEP CJ 1953 Service Manual
H

ELECTRICAL
SYSTEM
H-124. Testing Indicators and Gauges

Two
gauges
(fuel and temperature) and two in dicators (oil pressure and battery charge) that are
located in the instrument cluster

H

ELECTRICAL
SYSTEM
H-124. Testing Indicators and Gauges

Two
gauges
(fuel and temperature) and two in dicators (oil pressure and battery charge) that are
located in the instrument cluster are electrically operated.

The
fuel
gauge
is connected by a single wire to a
float-and-slide-rheostat sending unit in the fuel
tank.

The
temperature
gauge
is connected by a single

wire
to a resistance-type sending unit mounted on the engine.

The
battery charge indicator operates when there
is a difference in potential
between
the generator
and
the battery
.The
battery charge indicator lights
when the generator is not charging the battery. The
indicator
light
goes
out when the generator
begins

to charge the battery.

The
oil pressure indicator is connected by a single

wire
to a diaphragm switch located on the engine.
When
engine
oil pressure is low or zero and the
ignition switch is on, the oil pressure indicator
will

light. When
engine
speed is increased slightly above idle speed, raising the oil pressure to approximately 6 psi. [0,2 kg-cm2], the diaphragm switch
will
open the circuit and the indicator light
will
go out.

A
voltage
regulator maintains a constant
voltage
to the
gauges
in normal operation. On early vehicles,
this
voltage
regulator was mounted on the
rear
of
the instrument cluster. On current vehicles, the
voltage
regulator is integral with the fuel
gauge.

Should
trouble
develop
in the
gauges,
first check the regulator (fuel
gauge
on current production vehicle). If the
voltage
to the regulator is below 10 volts system low
gauge
readings
will
result.
Voltage in
excess
of 16 volts
will
not affect
gauge

readings but may result in premature wear of the
regulator contacts. If the
voltage
to the regulator is

within
the above limits, check the electrical con nections to the regulator (or fuel gauge), especially
the ground connection. If the readings of all the
gauges
is too high, or they all read too low, replace
the regulator (or fuel gauge).

If
the temperature
gauge
or heat indicator in the
instrument cluster have failed, the cause may
originate from the jumper bar shorting out against the instrument case.
Check
the jumper bar
between

the temperature
gauge
and heat indicator at the

rear
of the instrument case. On later production vehicles, the jumper bar is covered with an in
sulating
sleeve
to protect it from shorting out
against the instrument case. If the jumper bar

does
not have this
sleeve,
either install one or

wrap
the bar with plastic electrical tape to
half

an
inch [12,7 mm.] from each end. When installing the jumper bar, be sure the curved
segment
is
closest to the fuel
gauge.

Should
only one of the two
gauges
register incor
rectly,
check the lead wire from the
gauge
to the
sending unit for shorts or open connections. Next disconnect the
gauge
from the sending unit, and
connect the
gauge
to a new fuel tank sending unit

which
has been grounded to the vehicle.
If
the
gauge
registers incorrectly when operating the new unit,
replace the
gauge;
if correctly, replace the sending

unit.

Should
a new fuel tank unit not be available for testing, use a 12-volt
test
light in its place. When
the
gauge
is operating correctly, the pointer
will

move
approximately three-quarters across the
dial.

On
some
vehicles, the temperature
gauge
may
register on or
close
to the H (hot)
mark
when
coolant temperature is
190°F.
to
200°F.
[88°C.
a

93°C.].
In such cases, a 25-ohm,
1-watt
resistor
may be installed on the temperature
gauge
which

will
place the pointer just beyond the center
mark
at a coolant temperature of
190°F.
to
200°F.
Install

the resistor
between
the two terminals on the back
of the
gauge.
Insulate the
exposed
leads of the resistor with electrical tape.

If
the oil pressure indicator
does
not indicate cor

rectly,
first check the light bulb. Next check all
connections and lead wires. If, after all possible

defects
are corrected, the indicator light
does
not go on and off properly, then the diaphragm type
switch in the cylinder block should be replaced.

H-12S.
LIGHTING SYSTEM The
wiring of the lighting systems is shown in
the wiring diagrams, which indicate the various units in relation to their positions in the vehicle.
The
wires in the various circuits are of different
colors or are marked by tracers to aid when check
ing individual circuits.

The
lighting circuits of all models are protected by

an
overload circuit breaker mounted on the back of the main light switch and no replaceable fuse is
required.

The
upper and lower headlight beams are con
trolled by a
foot
switch located on the toe board
to the left of the clutch pedal.
H-126.
Main
Light
Switch

This
switch is a dual functioning unit having two

push-pull
positions and a rotary action. When
pulled out to the first position, the front parking
and
tail
lights are turned on. When pulled all the
way out to the second position, the headlights and
tail
lights are turned on. Rotating the switch to
the right dims the instrument cluster lighting.

The
switch may be removed from the instrument
panel by first loosening the set screw in the control
knob and removing the knob. The retaining nut may then be removed and the switch removed
through the
rear
of the instrument panel.
FIG.
H-51—MAIN
LIGHT
SWITCH
(EARLY)

1—
Battery
4—Parking Lights
2—
Rear
Lights 5—Auxiliary

3—
Head
Lights
212

Page 362 of 376

JEEP CJ 1953 Service Manual
u
MISCELLANEOUS
U-12.
STANDARD
AND
RECOMMENDED TOOLS
(Continued)

Tool
Description
CLUTCH

W-296 Fixture — Adjusting

TRANSMISSION

C-3201
- A
Lo-Jack
— Floor Type

AXLE

C-637

Page: < prev 1-8 9-16 17-24

tires alarm length airbag pairing phone auxiliary battery