1953 JEEP CJ tire type

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

FIG.
G-8—TEMPERATURE SENDING UNIT- HURRICANE
F4
ENGINE
1—Temperature
Sending Unit

b.
Dauntless V-6 Engine.

The
thermo-couple coolant sending unit is mounted
in
the left
rear
area of the intake manifold and is
connected by a single wire to the dash unit of
the instrument cluster.

G-ll.
WATER PUMP

a.
Hurricane
F4 Engine.

The
water pump on the
Hurricane
F4
engine
is a

centrifugal
impeller type of large capacity to
cir­

culate water in the entire cooling system. The double row
ball
bearing (Fig. G-9), is integral with
the shaft and is packed at assembly with a special
high melting point grease which
will
last the life of
the bearing. The bearing is sealed to retain the
lubricant
and prevent
dirt
and dust from entering.

The
bearing and shaft are retained in the water
pump body by the bearing retaining wire. The
water
seal bears against the ground seat on the
pump body and the inside of the impeller, maintain­
ing a constant pressure against both and preventing

water
leakage. A
drain
hole
in the
bottom
of the
pump body precludes any water
seepage
past the

seal
from entering the bearing.
The
impeller and the pulley hub are pressed on
the shaft under high pressure,
b.
Dauntless V-6 Engine.

A
centrifugal-type water pump, shown in
Fig.
G-10,

circulates
coolant through the Dauntless V-6
engine

and
its cooling system.
This
pump is mounted on
the timing chain cover.
Similar
to the
engine
cooling
fan
mounted on its hub, the pump is driven through
a
V-belt from the crankshaft pulley.

Coolant
enters the water pump at its center.
Centri­

fugal force then forces coolant radially outward, through vanes of the pump impeller, and backward
through two discharge passages in the timing chain cover. These passages conduct an equal amount of
coolant to each cylinder bank water jacket.
This

water
pump has a sealed double row
ball
bearing
and
a ceramic water seal, neither of which can be

serviced.
In
event
of bearing or water seal failure, the entire water pump assembly must be replaced.
G-l2.
Water
Pump Inspection

Check
the water pump for leaks, and excessive end play or
looseness
of the shaft in the pump. A

quick
way to check is to work the fan blades up
and
down by hand. If any play is noticed, this
indicates that the bearings are rough. Rough bear­ings should be checked to see if the water pump
should be replaced or rebuilt.

G-13.
Water Pump
Disassembly
—
Hurricane
F4
Engine

•
Refer to Fig. G-9.

a.
Remove the fan belt, fan blades, and fan pulley.

b.
Remove the
bolts
attaching the water pump
to the block. Remove the pump.

c.
Remove the bearing retainer spring.

d.
Remove the pump impeller and pulley with a suitable puller.

e.
Remove the pump seal, bearing and shaft, and

bearing
slinger.

G-l4.
Water Pump Reassembly
—
Hurricane
F4
Engine

•
Refer to Fig. G-9.
Before assembling the water pump, examine water
seal
seat in the pump body and should it be rough,

install
a new pump body.

To
reassemble the unit, insert the long end of the shaft into the pump body from the front end until
the outer end of the bearing is flush against the

FIG.
G-9—WATER
PUMP-
HURRICANE
F4
ENGINE

1—
Fan
and Pump Pulley
2—
Bearing
and Shaft

3—
Bearing
Retainer Spring

A—Pipe
Plug 5—
Pump
Body
6—
Seal
Washer 7—
Pump
Seal
8—
Impeller

9—
Gasket
167

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

H

12955

FIG.
H-8—PRESTOLITE
DISTRIBUTOR—DAUNTLESS V-6 ENGINE 1—
Cap
2—
Rotor

3—
Lubricating
Wick

4—
Snap
Ring
5—
Condenser

6—
Contact
Set 7—
Breaker
Plate
8—
Cam
and Stop Plate 9—
Spring
(2)
10—
Governor
Weight

11— Cam
Spacer

12—
Gear
13—
Gear
Pin
14—
Washer

15—
O-Ring
Seal
16—
Bushing

17—
Distributor
Housing 18—
Vacuum
Chamber
19—
Washer
(Nylon)
20—
—Cap
Clamp
and Rings

21—
—Primary
Lead
22—
Washer
(outer upper,

23—
Washer
(inner upper)

2".—Drive
Shaft
H-14. Governor Mechanism
The
centrifugal advance mechanism consists of

an
automatic cam actuated by two spring con­
trolled centrifugal weights. As the
speed
of the distributor shaft increases with
engine
speed, the

weights
are thrown outward against the pull of the springs.
This
advances the cam causing the contact
points
to
open
earlier and thus advancing the

spark.
The centrifugal
type
governor should be checked for free operation. Hold the governor shaft
and
turn the cam to the
left
as far as possible

and
release it. The cam should immediately return to the original position without drag. Should a distributor
test
fixture be available it is

best
to make a check through the entire advance
range, following the instructions of the fixture manufacturer.

The
vacuum control unit is mounted separately
on the
outside
of the distributor housing on the
V6
Prestolite distributor.
The
vacuum control unit consists of an enclosed
spring-loaded diaphragm linked mechanically to the distributor. The air-tight side of the diaphragm
is connected to the intake manifold side of the

carburetor.
Under part throttle operation, the in­take manifold vacuum is sufficient to actuate the
diaphragm and cause the distributor to rotate in
its mount, thus advancing the spark and increasing fuel
economy.
During acceleration or when the
engine
is pulling heavily, the vacuum is not suf­
ficient to actuate the diaphragm and the distributor
is held in the retarded position by a calibrated

return
spring which bears against the vacuum
diaphragm.

H-15.
Distributor Removal

a.
Remove high-tension wires from the distributor cap terminal towers, noting the order in which
they

are
assembled to ensure correct reassembly.
b. Remove the primary lead from the terminal

post
at the coil.
c. Unlatch the two distributor cap springs and re­
move
the cap.

d.
Note
the position of the rotor in relation to the
base.
This
should be remembered to facilitate re­ installing and timing.
e. Remove the screw holding the distributor to the

crankcase
and lift the assembly from the
engine.

H-16.
Prestolite Distributor Disassembly

Refer
to Fig. H-8 and H-9.

a.
Remove the rotor. b. Remove the condenser.
c. Remove the distributor points.
d.
Remove nylon washer attaching vacuum ad­vance arm to breaker plate, V6 only. Remove two 181

N

REAR
AXLE a.
Place the transmission in neutral.

b.
Raise one wheel off the floor and place a block

in
front and at the
rear
of the
opposite
wheel.

c.
Apply a torque wrench to the axle shaft nut of
the elevated wheel.

d.
Turn
wheel with torque wrench. Disregard

breakaway
torque and observe torque required to
continuously
turn
wheel smoothly. Torque should
read
40 lb-ft [5,53 kg-m.] or more.

N-23. Powr-Lok
Differential Disassembly
/
and Reassembly

Refer
to
Figs.
N-38 and N-39.
The
procedure for overhauling disc type
Powr-Lok

differentials is as follows:

a.
Remove axle shafts following procedure de­
scribed
in Par. N-2.

b.
Remove housing cover and gasket.

c.
Remove the
Powr-Lok
differential from the axle.
Do not remove the ring gear or bearing
cone
and

rollers
unless replacement is to be made.
Mark
the hearing cups so they may later be reassembled

with
the same bearing cones.
Mark
the differential
case halves for correct alignment at reassembly.
Each
pinion mate cross shaft should also be marked
so that each pin cam surface
will
match with the
same
V-ramp
in the case when reassembled.

d.
Separate the case halves. e. Remove the disc and plate
sets.
The illustration
(Fig.
N-39) shows the arrangement of plates and

discs.
When reassembling unit, discs and plates must be reinstalled in this arrangement. Be sure
to keep in mind which way the set
will
face toward the case.

^®(j)(j)CD©
® /'Ml
I
11
11 v

FIG.
N-39—PLATE
ASSEMBLY
ORPER
A—Model
44
B—Model
27 1—
Case
5—Disc

2—
Belleville
Plate
6—Thin
Plate

3—
Belleville
Disc
7—Sidegear
Ring

4—Plate
8—Side
Gear
f. Remove the pinion mate cross shafts, bevel
pinion mate gears, bevel side gears, and side gear

rings.

g.
Clean
all parts thoroughly in kerosene and dry

with
compressed air.

h.
Inspect all parts. Replace any items which ap­

pear
to be worn or damaged.

i.
Inspect the plate surfaces of the case halves, the
side gear rings, and the clutch friction plates and
discs for excessive wear or scoring.

j.
Inspect the pinion mate shaft and ramp
sur­

faces on the case for excessive wear and pitting,

k.
Inspect the pinion gear races that bear on the
side gear rings.

I.
Inspect the corresponding surfaces on the side
gear rings.

m.
Inspect the clutch plates and discs for cracks

and
distortion. In the
event
one or more of the

clutch
plates or discs
needs
replacing, replace the
entire stack of plates and discs on each side of
the pinions. These stacks are supplied in
sets.

The
differential case halves are not serviced. Should replacement be required, it is necesary to replace
the complete differential.

n.
Assemble the clutch friction plates, clutch
fric­

tion discs, and dished plates on the splined hub of each bevel side gear. Make sure the plates and
discs are installed in the proper relationship as shown in Fig. N-39. The dished plates in the plate

and
disc set are always assembled with the convex
side toward the case. As each part is reassembled

in
its proper position, it is necessary that it be lightly coated with
Powr-Lok
lubricant,

o.
Place each differential case
half
on its side and
install
the side gear rings with the plates and discs
assembled. The side gear ring
will
rotate with a slight drag when properly located in the case,
p.
With
the ring gear flange
half
of the differential
case in an upright position, assemble the bevel side gears, pinion mate cross shafts, and bevel pinion
mate gears.
Install
the remaining case
half
on the
ring
gear flange half. Make sure that all markings
coincide.

q.
Install
the differential case
bolts
and
turn
them

in
a few threads.

r.
Using axle shafts from the vehicle, align the
splines of the side gear, and the side gear
ring,

s.
With
these
axle shafts in position, tighten the

differential
case
bolts
evenly. Torque 35 to 45 lb-ft. [4,84 a 6,22 kg-m.].
t. Remove the axle shafts.

u.
Check
for proper assembly.
Each
pinion mate
cross shaft should be tight on its
ramp.
If there is

clearance
between
the cross shaft and the
ramp,

the clearance should be no more than .005" [0,127 mm.].

This
clearance should be equal on all four cross
shaft ends.
v. Reinstall the unit in the axle.

w.
Install
axle shafts as described in Par. N-2.
Other
service operations such as ring gear and
pinion replacement, or pinion and bearing adjust­ ments, are performed in the same manner as de- 302

p
BRAKES

13264

FIG- P-2—DOUBLE
SAFETY BRAKE
MASTER
CYLINDER
With
the Double-Safety brake system type master

cylinder,
failure
in one part of the brake system

does
not result in
failure
of the entire hydraulic
brake system. Failure in the
front
brake system
will

leave the rear brake system
still
operative or
failure
in
the rear system
will
leave the
front
brake system

operative.

A
double hydraulic
cylinder
with
two outlets, two
residual
check valves, two
fluid
reservoirs, and

two
hydraulic pistons (a
primary
and secondary)
are operated in tandem by a single hydraulic push
rod.
The
primary
outlet is connected to the
front

brakes
with
the secondary outlet connected to the rear brakes.

With
the master
cylinder
fluid
reservoirs
filled
and the
front
and rear brake system
bled,
there is a
solid
column
of
fluid
on the
forward
side of both the

primary
and the secondary pistons.

Upon
application
of the brakes, through movement

of
the brake pedal,
fluid
is displaced by the pistons

into
the wheel cylinders to activate both
front
and
rear brakes.
Upon
release
of the brakes,
fluid
re­
turns
from
the rear wheel cylinders through the secondary residual check valve to the secondary

portion
of the master
cylinder
bore.
Fluid
also
returns
from
the
front
wheel cylinders through the

primary
residual check valve to the
primary

portion
of the master
cylinder
bore.

P-3.
Parking
Brakes
— DJ-5, DJ-6

a.
The parking brake is operated by a T-handle

lever
mounted to the
left
of the steering
column
and
suspended
from
the instrument panel. When
the brake lever is
pulled
outward, tension is exerted
on
the parking brake cable leading to the brake.
The
amount of brake
grip
depends
on the number

of
notches the lever is
pulled
out. To set the park­
ing
brake,
pull
out on the parking brake
control
T-handle.
To
release
the brake,
turn
the handle

slightly
and push it
forward.

0

FIG.
P-3—PARKING
BRAKE LINKAGE
—
DJ-5,
DJ-6
1—
Cable
and
Conduit
(Front)
7—Retracting
Spring
Link
13—Brake
Lever
Bracket

2—
Clip
8—Nut
14—Clevis
Pin

3—
Grommet
9—Nut
15—Cotter
Pin
4—
Hand
Brake
Handle
Assembly
10—Equalizer
16—Clevis
Pin

5—
Cable
and
Conduit
(Rear)
11—Adjusting
Rod
17—Cotter
Pin
6—
Retracting
Spring
12—Hand
Brake
Lever
324

p

BRAKES
be either a defective master cylinder or the use of
low grade brake fluid which has expanded because
of heat. Use standard duty brake fluid conforming to
SAE-J1703
specification.

P-7.
Bleeding
Brakes

The
hydraulic
brake system must be bled whenever

a
fluid line has been disconnected or air
gets
into the system. A leak in the system may sometimes
be indicated by the presence of a spongy brake
pedal.
Air trapped in the system is compressible

and
does
not permit the pressure, applied to the
brake
pedal, to be transmitted solidly through to
the brakes. The system must be absolutely free
from
air at all times. When bleeding brakes, bleed
at that wheel with the
longest
line from the master
FIG.
P-5—BLEEDING
BRAKES

1—Bleeder
Screw
cylinder
first, the next
longest
second, etc. During
the bleeding operation the master cylinder must
be kept at least %
full
of hydraulic brake fluid.

To
bleed the brakes, first carefully clean all
dirt

from
around the master cylinder filler plug. If
bleeder tank is used follow the manufacturers in­
structions.
Remove the filler plug and
fill
the master
cylinder
to the lower
edge
of filler neck.
Clean
off

all
bleeder connections at all four wheel cylinders.

Attach
bleeder
hose
and fixture to right
rear
wheel

cylinder
bleeder screw and place end of tube in a
glass jar, and submerged in brake fluid. Open the bleeder valve one-half to three-quarters of a
turn.

See
Fig.
P-5.
Depress the
foot
pedal, allowing it to return very
slowly. Continue this pumping action to force the
fluid
through the line and out of the bleeder
hose
which
carries with it any air in the system. When bubbles cease to appear at the end of the bleeder
hose, close the bleeder valve and remove the hose.
After
the bleeding operation at each wheel cylinder
has been completed,
fill
the master cylinder reser­
voir
and replace the filler plug.
Do not re-use the liquid which has been removed

from
the lines through the bleeding process because
of air bubbles and
dirt.

P-8.
Brake Hoses

a.
Hydraulic
lines (tubing and hose) are the means
of transmitting fluid under pressure between the master cylinder and the wheel cylinders.

Note:
On
some
vehicles a proportioning valve is
located in the
rear
brake line along the inside left
frame
side
rail.
The valve is not serviceable and
must be replaced as an assembly.

Should
replacement be necessary make certain the valve is properly positioned with the centerline of
the hex plug (in the bottom of the valve) in the
vertical
position. Refer to Fig. P-l.

The
hoses
are the flexible links between the wheels

or
axles and the frame or body. The
hoses
must

withstand
the fluid pressures without expansion
and
must be free to flex during spring deflection
and
wheel turns without causing damage to the
hose.

b.
Hydraulic
lines are subject to damage and
deterioration. Hoses should be inspected for cuts,

chafing,
cracks,
twists and
loose
frame supports.

Hydraulic
tubing should be inspected for signs of
leakage (due to faulty flares or
loose
connections);

restrictions
(due to dents or corrosion); and wear (due to friction against other metal parts). Always
use correct type and size of wrench on fittings.

Avoid
damage to female fittings by supporting fit­
ting with tube nut during removal of assembly.

c.
On fittings where gaskets are used, always use
a
new gasket. Copper gaskets take a set and may
not form a
good
seal if reused.

d.
When replacing hydraulic brake hose, attach
hose
to wheel cylinder and securely tighten hose,
then attach
opposite
end to frame fitting or tubing.
Avoid
twists in
hose
when assembling to frame fitting
or
tubing. Hold
hose
end securely with

wrench
while attaching tubing to hose. If
hose
end
clip
is used, make certain clip is assembled properly.

Check
for interference during spring deflection or
rebound and during front wheel turns.

e.
Check
for any possible contact between front

brake
hose
and inner sidewall of tire when the front
wheels are in maximum
turn
position.
Check
for sufficient but not excessive length of
hose
between
the clamp and the wheels by turning the wheels
from
one extreme
turn
position to the otherl
f.
Check
that there is no possibility of any contact between the
tail
pipe and
rear
brake
hose
under
all
operating conditions.
P-9.
Brake Pedal Adjustment

There
should always be at least W [12,7 mm.]
free pedal travel before the push rod
engages
the master cylinder piston.

This
adjustment is accomplished by shortening or 326

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

FIG.
Q-5—REAR
WHEEL

ATTACHING
PARTS —
FLANGED
AXLE

1—
Brake
Backing Plate

2—
Retainer
Ring

3—
Unit-Bearing

4—
Oil
Seal
5—
Retainer
Plate 6—
Brake
Drum
7—
Cup
Plug
8—
Flanged
Axle Shaft
14284

Q-4. Checking
Front
Wheel Bearings

Raise
the front end of the vehicle with a
jack

so that the tires clear the floor.

Grip
the tire and
test
sidewise shake of the wheel.

If
bearings are correctly adjusted, shake of the
wheel
will
be just perceptible and wheel
will
turn

freely with no drag.

If
bearing adjustment is too tight, the rollers may

break
or
become
overheated. Loose bearings may cause
excessive
wear and noise.

If
this
test
indicates bearing adjustment is neces­

sary,
follow
the procedure given in Par. Q-5. Loose
bearings
will
cause sidewise shake that is evident

around
the entire circumference of the wheel. A shake that is evident only when gripping the
wheels
in
a plane parallel to the ground, but not evident

around
the entire circumference, probably indicates
looseness
in the steering linkage.

Q-5.
Front Wheel Bearing Adjustment
With
the vehicle on the
jack,
the following proce­

dure
should be followed to adjust the front wheel
bearings on four wheel-drive vehicles.
a. Remove the hub cap, snap
ring,
capscrews, and
washers that attach the driving
flange
to the hub.

b.
Using the
Front
Axle Shaft Drive Flange Puller

W-163,
pull
the driving flange.
c. Bend the lip of the nut lock washer so that the

locknut
and lock washer may be removed.

d.
Rotate the wheel and tighten the adjustment nut until the wheel binds.

Note:
Front
tire and wheel must be rotated by

hand
as the adjusting nut is
tightened
to ensure positive seating of the bearing.

Then
back off the adjusting nut about one-sixth
turn
making sure that wheel rotates freely without
sidewise shake.
e. Replace the lock washers and locknut. Bend
over the lock washer lip.
f.
Check
the adjustment (Par. Q-4). Reassemble the driving
flange
and hub cap. Make certain the
gasket is properly installed
between
the hub and
the flange.

•
Model DJ-5, DJ-6

On
two-wheel drive vehicles, remove the hub cap
and
the wheel retaining nut cotter pin. Rotate the
wheel and tighten the wheel retaining nut until the wheel binds.
Then
back off nut about one-sixth
turn
or more if necessary making sure wheel ro­

tates
freely without sidewise shake. Replace the cotter pin and hub cap.

Q-6.
Rear
Wheel Bearing Adjustment —

Flanged
Axle Shaft

Vehicles
equipped with the
flange
type
rear
axle
shaft require no wheel bearing adjustment. The flanged axle shaft is equipped with a single row,

pre-adjusted,
tapered roller unit-bearing capable of
accepting thrust in either direction. The unit-

bearing
adjustment is built in at the factory mak­
ing shimming or bearing adjustment unnecessary.

Refer
to Fig. Q-6.

Q-7.
Checking
Rear
Wheel Bearings —
Tapered
Axle

Raise
wheel on which adjustment is to be made
by placing a
jack
under the axle housing.
With
hands,
test
sidewise shake and in and out play
of the wheel. If bearings are correctly adjusted,
shake of wheel
will
be just perceptible and the 337

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

Q
ice, provide maximum safety over all
types
of

terrain,
and furnish the medium on which the
vehicle can be maneuvered with ease. Although
there are other
elements
of tire service, inflation maintenance is the most important and in many
instances the most neglected. The tire pressure should be maintained for safe operation. An under- inflated tire is dangerous as too much flexing can
cause breakage of the casing. Overinflation in time
may
cause a blowout.

Upon
careful inspection of tires, it may be found
that improper wheel alignment, balance, grabbing
brakes,
poor driving habits, fast cornering or other
conditions are the cause of wear. Such conditions
should be corrected.

a.
UNDERINFLATION

Underinflation
distorts the normal contour of the
tire
body and the tire
bulges
or "bellies out" with

an
extreme flexing action.
This
wears the tread at the
edges
more than the center and generates
excessive internal heat, weakening the cords and
resulting
in bruises, broken cords or ply separation.

Underinflation
also leads to rim bruises as in­ sufficient resistance is provided to prevent the tire

from
being jammed against the rim and crushed
or
cut when the tire strikes a
curb,
rock, or rut.

b.
OVERINFLATION

When
a tire is
overinf
lated,
increased tension caused by excessive pressure prevents proper deflection of
the sidewalls.
This
results in wear in the center of the tread and the tire also
loses
its ability to absorb

road
shocks. Under this increased
strain,
cords in the tread area eventually snap under impact, caus­ing a casing break.

c.
MISALIGNMENT
WEAR
Excessive
wheel camber causes the tires to run at an angle to the road when camber is incorrect

it
will
cause excessive wear on one side of the
tire
tread.

Front
wheels should be straight ahead or toe-in slightly. When there is excessive toe-in or
toe-out,

tires
will
revolve with a side motion and scrape
the tread rubber off.
Front
tires
will
show wear on the outside with too great a toe-in condition
and
on the inside with a
toe-out
condition.

d.
BALANCE
Cupping
and bald spotting of tires is associated

with
wear on a vehicle driven mostly at high-way
speeds
without the recommended tire rotation and

with
unbalance conditions.

Q-12.
Tire
Care
Note;
For satisfactory 4-wheel drive operation, a
4-wheel drive vehicle
MUST
be equipped with the same size tires of equal circumference on all
four wheels. The tires must then be inflated to

proper
factory recommended pressures at all times.

Tire
pressure, tire rotation, wheel balance, and wheel alignment are the four vital factors that in­
fluence the
extent
of tire life and the
ease
and safety of vehicle control.
Four
of the most common

tire
troubles are:

a.
Excessive wear around the outer
edges
resulting

from
underinflation.

b.
Excessive wear in the center of the tread re­
sulting from overinflation.

c.
Tire
tread worn on one side indicating wheels
need realigning.
d.
Cuplike
depressions on one side of the tread

indicating
wheels need balancing.

If
the vehicle normally carries a
full
load, two to
four psi. [0,14 a 0,28 kg-m2] can be added to the
recommended air pressures. But, remember that adding air with a light load means a harsher ride,

doesn't
help tires, and wears out shock absorbers. Rotate the tires as shown in Fig. Q-9 for correct
rotation system.

Q-13.
Tire
Removal
and
Installation

To
remove a tire from a drop center rim, first
WEAR
AT SHOULDERS

WEAR
AT CENTER

WEAR
ON ONE
SIDE
FEATHERED
EDGE
BALD
SPOTS

/1TTDN

i

UNDER
INFLATION
OVER
INFLATION
EXCESSIVE
CAMBER

INCORRECT
TOE
WHEEL
UNBALANCED

liF
11

ADJUST
PRESSURE TO
SPECIFICATIONS
WHEN
TIRES ARE
COOL
ADJUST
CAMBER
TO

SPECIFICATIONS
ADJUST
FOR

TOE-IN
DYNAMIC
OR
STATIC

BALANCE
WHEELS

FIG.
Q-8—TIRE
WEAR
PATTERN
339

Q

WHEELS

11463

FIG.
Q-9—TIRE
ROTATION
1—
Right
Front
Tire

2—
Right
Rear
Tire

3—
Spare
Tire
4—
-Left
Rear
Tire

5—
Left
Front
Tire
deflate completely and then force the tire away

from
the rim throughout the entire circumference
until
the bead falls into the center of the wheel

rim.
If the vehicle is equipped with tires that use

an
inner tube, carefully remove the inner tube.
With
the inner tube removed, or on tubeless tires, a tire
removing tool should be used to remove the tire

from
the rim.

Installation
of the tire is made in the same manner
by first dropping one side of the tire into the center
of the rim and with a tire tool raise the bead over
the wheel
rim.
The inner tube can now be installed
on vehicles so equipped.
When
mounting the wheel, alternately tighten op­
posite stud nuts. After the nuts have been tightened

with
the wheel jacked up, lower the
jack
so wheel rests on the floor and retighten nuts. Torque nuts
to 60-75 lb.-ft. [8,3 a 10,4 kg-m.].

Note:
New "wide" tires have been given new sizes
by tire manufacturers. They use a letter as a key
unit
in the name size for the new wide treads.

The
single letter in front of the "70" indicates load rating, or the weight a tire can support safely
when inflated to 32 psi. The number 70 is used to show the
7-to-10
(70 percent) ratio of tire section height to width. The last two-digit number of the new sizes— 15 —
is
the rim diameter.
Radial

ply
tire sizes all contain the letter
"R"
to designate
radial
ply construction.

15-inch
Diameter
New Old

E70-15
7.35-15

F70-15
.7.75-15

G70-15
8.15-15

H70-15
8.45-15
J70-15
.8.85-15

K70-15
. .... .9.00-15

L70-15
9.15-15

You
should explain to customers
these
new tire
designations. Such knowledge
will
act as a re­
minder
never to mix
radial
ply, wide treads or
conventional tires on one axle.
0-14.
WHEEL
AND
TIRE
SPECIFICATIONS
'Jeep'

Universal

V6
Engine

CJ-5,
CJ-6,
CJ-5A,
CJ-6A
'Jeep*

Universal

F4
Engine

CJ-3B,
CJ-5,
CJ-6
DJ-5,
DJ-6

WHEELS:
Rim
Size 15 x
6.00
16 x 4.50
15 x 5.50

K
E
K

Attachment

Type
Stud
Stud Stud

Circle
Dia 5.50 5.50 5.50

5 5
4

Size
H-20
H-20
H-20

Rear
Axle Shaft End Float .001*-.006"
.001"-.006" .001 *-.006"
[0 ,025 a 0,152 mm.)
[0,025 a 0,152 mm.] [0,025 a 0,152 mm.]

TIRES:
Size.
7.35-15

6.00-16
6.85-15

Ply
Rating 4
4 2
Revolutions per Mile @ 30 mph.. . 781 730 803

Inflation
Pressure

Front
20
psi
[1,406 kg-cm2]
20 psi [1,406 kg-cm2] 24 [1,687 kg-cm*]

Rear
24
psi
[1,687 kg-cm*]
20 psi [1,406 kg-cm2] 24 [1,687 kg-cm*] 340