1953 JEEP CJ remove seats

'Jeep*
UNIVERSAL SERIES SERVICE
MANUAL

P
f. On vehicles without a transmission brake hold
the brake
shoes
in their relative position and
engage
the parking brake cable
into
the parking

brake
lever.
g. On vehicles without a transmission brake in­
stall
the parking brake strut and spring
between

the parking brake lever and the primary
shoe.

h.
Place the brake
shoes
on the backing plate and

install
the retainer pins, springs and retainers.

i.
Install the anchor pin plate.

j.
Install the lever and
sleeve
on the primary
shoe
then install the secondary return spring, then the
primary
return spring.

Important:
A
"L"
or "R" is located on the hex­

agon
side of the lever crank for identification. The
lever crank marked "R" applies to the primary
shoe
on the
left
rear brake assembly. The lever
crank
marked
"L"
applies to the primary
shoe
on
the right rear brake assembly.
k. Place the upper linkage rod in the
groove
of the
anchor pin and
engage
the hook of the link rod
into

the adjusting lever.

I.
Install the brake drum. Install the wheel and

tire
assembly.
m. Adjust the brakes as described
below.

P-19.
Brake
Shoe
Initial
Adjustment —

a.
Should wheel brake units have
been
disassem­ bled for any reason, an initial adjustment
MUST
be made
before
drum installation.

b.
When the brake parts have
been
installed in
their correct position, initially adjust the adjusting
screw assemblies to a point where approximately Y% [9,53 mm.] of threads are
exposed
between
the

star
wheel and star wheel nut.

Note:
Following the initial adjustment and final
assembly, check brake pedal height to ensure

brake
operation. Then drive the car in reverse and
FIG.
P-12—BRAKE SHOE ADJUSTMENT
1—
Star
Wheel
2—
Lever

3—
Screwdriver
4—
Brake
Adjusting Tool
forward,
making 10 to 15 brake applications prior
to road testing.
This
action balances the adjust­
ment of the four brake units and raises the brake
pedal.
c. Adjustment may be made manually by remov­ing the access
slot
cover and using a brake adjust­
ing
tool
or screw driver to rotate the star wheel
until
the wheel is in the locked position. To tighten, rotate the star wheel in the clockwise direction.
Then
back off the star wheel at least 15 to 20

notches
(clicks).

d.
To back off the star wheel on the brake, insert
ice pick or thin blade screw driver in adjusting screw
slot
to hold lever away from adjusting screw.

Back
off on adjusting screw until wheel and drum

turn
freely. Replace adjusting
hole
cover.

Caution:
DO NOT attempt to back off on ad­
justing screw without holding adjuster lever away from screw as adjuster
will
be damaged.
P-20. Master Cylinder Reconditioning —
Dual
System

Refer
to Fig. P-13.

DISASSEMBLY
a.
Remove the filler cap and empty all fluid.
b.
Remove the snap ring, push rod assembly, and
the primary and secondary piston assemblies. Air pressure applied in the piston
stop
hole
will
help
facilitate the removal of the secondary piston as­
sembly.
c. The residual check valves are located under
the front and rear fluid
outlet
tube
seats.

d.
The
tube
seats
must be removed with the
self-

tapping screws supplied in the repair kit to permit removal of the check valves. Screw the self-tapping
screws
into
the
tube
seats
and place two screw

driver
tips under the screw head and force the
screw upward as shown in Fig. P-14.
e. Remove the expander in the rear secondary cup, secondary cups, return spring, cup protector,
pri­

mary
cup, and washer from the secondary piston.
f. The primary piston, with the rubber cups in­ stalled, is supplied in the repair kit.

CLEANING
a.
After disassembly, immersion of all metal parts
in
clean brake fluid or a brake system cleaner is
recommended. Use air
hose
to blow out dirt and cleaning solvent from recesses and internal pas­

sages.
When overhauling a hydraulic brake unit,
use all parts furnished in the repair kit. Discard
all
old rubber parts.

b.
After cleaning, place
all"
hydraulic
system parts
on clean paper or in a clean pan.

INSPECTION
Inspect all other parts for damage or
excessive

wear.
Replace any damaged, worn, or chipped
parts.
Inspect hydraulic cylinder bore for
signs
of
scoring, rust, pitting, or etching. Any of
these
will
require
replacement of the hydraulic cylinder. 331

BRAKES

12519

FIG.
P-13—DOUBLE
SAFETY MASTER CYLINDER
1— Boot
2— Snap Ming 3"*—Piston Assembly
4—
Backing
Ring 5—
Master
Cylinder Cup 6—
Master
Cylinder Cup
7— Piston
8—
Master
Cylinder Cup 9—
Cup
Protector
10—Spring 11—
Cylinder
Housing
12—
Cover
Gasket
13—
Cover

14—
Washer
Gasket 15—
Washer
16—
Cover
Bolt
17—
Check
Valve Spring 18—
Check
Valve
19—
Tube
Seat
20— Piston Stop
REASSEMBLY

a.
Prior
to reassembly of the master cylinder, dip

all
components
in clean brake fluid and place on
clean paper or in a clean pan.

b.
Install the primary cup washer, primary cup,
cup protector, and return spring on the secondary piston.
c. Install the piston cups in the double
groove
end
of the secondary piston, so the flat j of the cups face each other (lip of cups away from each other).
Install
the cup expander in the lip
groove
of the
end cup.

cL
Coat the cylinder bore and piston assemblies with clean brake fluid
before
installing any parts

in
the cylinder.
e. Install the secondary piston assembly first and then the primary piston which is supplied in the
repair
kit.

f.
Install the push rod assembly, which includes
the push rod,
boot,
and rod retainer, and secure
with the snap ring. Install the primary piston
stop.

g. Place new rubber check valves over the check valve springs and install in the
outlet
holes, spring
first.

Note:
When replacing a
complete
master cylinder
with a service unit, the original push rod must be used. The push rod retainer and snap ring retainer 12617

FIG.
P-14—REMOVING TUBE SEATS 1
—Screwdriver

2— No. 6-32 Self-Tapping Screw

3—
Tube
Seat must be removed and discarded. As the new unit
has the retainers installed it is only necessary to

install
the push rod until a "snap" is heard and the push rod is retained. 332

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

P h.
Install
the tube seats, flat side toward the check

valve,
and press in with tube nuts or the master

cylinder
brake pipe tube nuts.

BLEEDING
a.
Before the master cylinder is installed on the
car,
the unit must be bled.

b.
Support the cylinder assembly in a vise and

fill
both fluid reservoirs with approved brake fluid,

e.
Loosely install a plug in each
outlet
of the

cylinder.
Depress the push rod several times until

air
bubbles cease to appear in the brake fluid.

d.
Tighten the plugs and attempt to depress the piston. The piston travel should be restricted after
all
air is expelled.
e.
Install
the master cylinder on the car and bleed
the hydraulic lines at the wheel cylinder. Refer to
Par.
P-7.

P-21.
Wheel
Cylinder
Reconditioning
•
Refer to Fig. P-15.
Note:
Make sure a replacement brake cylinder
has the same part number as the original cylinder.

FIG.
P-15—WHEEL
BRAKE CYLINDER
1— Boot

2—
Piston

3—
Cylinder
Cup
4—
Cup
Spring
5—
Cylinder

6—
Bleeder
Screw
a.
To remove a wheel cylinder,
jack
up the vehicle

and
remove the wheel, hub, and
drum.
Disconnect
the brake line at the fitting on the brake backing
plate. Remove the brake
shoe
return spring which

will
allow the brake
shoes
at the toe to
fall
clear of the brake cylinder. Remove two screws holding
the wheel cylinder to the backing plate.
b.
Remove the rubber dust covers on ends of

cylinder.
Remove the pistons and piston cups and
the spring.

c.
Wash the parts in clean alcohol.

d.
Examine the cylinder bore for roughness or
scoring.
Check
fit of pistons to cylinder bore.
e. When reassembling the cylinder, dip springs, pistons and piston cups in brake fluid.
Install

spring
in center of the wheel cylinder.
Install

piston cups with the cupped surface towards the

spring
so that the flat surface
will
be against
the piston.
Install
pistons and dust covers.
f.
Install
wheel cylinder to the backing plate and connect brake line and install brake
shoe
return

spring.

g. Replace wheel, hub, and
drum.

h.
Bleed the brake lines (Par. P-7).

P-22. TROUBLE
SHOOTING

P-23.
Squeaky
Brakes

In
most cases, squeaks are entirely eliminated by

correct
adjustment of the brakes. Squeaks may be
caused however, by glazed linings, lining wore thin
to the point of
exposed
rivets or by vibration. A

drum
will
not vibrate when the brake is securing

uniform
contact over the entire lining surface, ex­
cept when due to improper conditions such as the
linings becoming glazed.
Glazed
surface of the

brake
linings may be removed by a stiff
wire
brush.
Occasionally
squeaks are caused by roughened
sur­

face of the
drum,
which can usually be remedied
by rubbing down with emery cloth and by wiping
the brakings surface clean. In extreme cases it may
be necessary to reface the drum in a lathe. Should
this be done, do not remove a metal thickness greater than .030" [0,762 mm.] - .060" [1,52 mm.]

overall
diameter.

P-24. Rattles
in
Brakes

See that the tension of the springs in the brakes

and
attached to the control system are sufficient to

return
brakes and brake mechanism to their normal
position.
Return
springs are so placed that they
keep all slack out of the control system by tension on all joints.

Brakes
will
not rattle inside the
drum
if the springs
holding the
shoes
are kept at the proper tension. 333